Bosch FLEXIDOME IP micro 3000i-outdoor User manual

FLEXIDOME IP micro 3000i ‑ outdoor |
FLEXIDOME IP turret 3000i IR ‑ outdoor
NDE‑3502‑F02 | NDE‑3502‑F03 | NDE‑3503‑F02 | NDE‑3503‑F03 |
NTE‑3502‑F02L | NTE‑3502‑F03L | NTE‑3503‑F02L | NTE‑3503‑F03L
en User manual

FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor Table of contents | en 3
Bosch Security Systems B.V. User manual 2020-12 | V01 | F.01U.385.759
Table of contents
1Browser connection 5
1.1 System requirements 5
1.2 Establishing connection 5
1.3 Password Network 6
2System overview 7
2.1 Live page 7
2.2 Playback 7
2.3 Configuration 7
2.4 Dashboard 8
3Operation via the browser 9
3.1 Live page 9
3.2 Playback page 11
3.2.1 Selecting the recording stream 11
3.2.2 Searching for recorded video 12
3.2.3 Exporting recorded video 12
3.2.4 Track list 12
3.2.5 Controlling playback 12
3.3 Dashboard 12
4Configuration 14
4.1 General 14
4.1.1 Identification 14
4.1.2 User Management 14
4.1.3 Date/Time 15
4.1.4 Display Stamping 16
4.1.5 GB/T 28181 18
4.2 Web Interface 18
4.2.1 Appearance 18
4.2.2 'Live' functions 20
4.3 Connectivity 21
4.3.1 Cloud services 21
4.3.2 Accounts 21
4.3.3 DynDNS 22
4.4 Camera 22
4.4.1 Installer Menu 22
4.4.2 Color 26
4.4.3 ALC 27
4.4.4 Enhance 28
4.4.5 Encoder Profile 29
4.4.6 Encoder Streams 30
4.4.7 Encoder Statistics 31
4.4.8 Encoder Regions 31
4.4.9 Privacy Masks 32
4.4.10 Audio 32
4.4.11 Pixel Counter 32
4.5 Recording 33
4.5.1 Storage Management 33
4.5.2 Recording Profiles 34
4.5.3 Maximum Retention Time 36

4en | Table of contents FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor
2020-12 | V01 | F.01U.385.759 User manual Bosch Security Systems B.V.
4.5.4 Recording Scheduler 36
4.5.5 Recording Status 37
4.5.6 Recording Statistics 37
4.5.7 Image Posting 37
4.5.8 SD Card Status 37
4.6 Alarm 38
4.6.1 Alarm Connections 38
4.6.2 Video Content Analysis (VCA) 39
4.6.3 Audio Alarm 43
4.6.4 Alarm E-Mail 43
4.6.5 Alarm Inputs 44
4.6.6 Alarm Outputs 45
4.6.7 Alarm Task Editor 45
4.7 Network 46
4.7.1 Network Services 46
4.7.2 Network Access 46
4.7.3 Advanced 48
4.7.4 Network Management 48
4.7.5 Multicast 50
4.7.6 IPv4 filter 51
4.8 Service 51
4.8.1 Maintenance 51
4.8.2 Licenses 52
4.8.3 Certificates 52
4.8.4 Logging 53
4.8.5 System Overview 53
5Troubleshooting 54
5.1 Physical reset button 54
6Appendices 55
6.1 Copyright notices 55

FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor Browser connection | en 5
Bosch Security Systems B.V. User manual 2020-12 | V01 | F.01U.385.759
1 Browser connection
A computer with Microsoft Internet Explorer is used to receive live images, control the unit,
and replay stored sequences. The unit is configured over the network using the browser.
1.1 System requirements
Our recommendations are:
– Computer with Dual core HyperThreading processor or better
– Graphic card with performance that matches or is better than the resolution of the
camera
– Windows7 or later operating system
– Network access
– Internet Explorer version 11 or later
– or –
Application software, for example, VideoSecurityClient, BoschVideoClient or BVMS.
Note:
To see live images in your browser it might be necessary to download and install the MPEG-
ActiveX from the Bosch download store.
1.2 Establishing connection
The unit must have a valid IP address to operate on your network and a compatible subnet
mask.
By default, DHCP is pre-set at the factory to On plus Link-Local so a DHCP server assigns an
IP address or, if no DHCP server is available, a link-local address (auto-IP) is assigned within
the range 169.254.1.0 to 169.254.254.255.
You can use IP Helper or Configuration Manager to find the IP address. Download the software
from http://downloadstore.boschsecurity.com.
1. Start the Web browser.
2. Enter the IP address of the unit as the URL.
3. During initial installation, confirm any security questions that appear.
Note:
If you cannot connect, the unit may have reached its maximum number of connections.
Depending on the device and network configuration, each unit can have up to 50 web browser
connections, or up to 100 connections via BoschVideoClient or BVMS.
Password protection in the device
The device is password protected across various authorization levels.
You must set a password for the ‘service’ authorization level to get access to the device.
Make sure the password obeys these conditions:
– 8 to 19 characters in length
– Upper and lower case letters
– Minimum of 1 digit
– Minimum of 1 special character
These special characters are not allowed: ‘@’, ‘&’, ‘<’, ‘>’, ‘:’, ‘+’
1. Enter the password in the two text fields.
2. Click Set. If the password is valid, you get access to the device.

6en | Browser connection FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor
2020-12 | V01 | F.01U.385.759 User manual Bosch Security Systems B.V.
1.3 Password Network
If a RADIUS server is used for network access control (802.1x authentication), the unit must
be configured first. To configure the unit, connect it directly to a computer using a network
cable and configure the two parameters, Identity and Password. Only after these have been
configured can communication with the unit via the network occur.

FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor System overview | en 7
Bosch Security Systems B.V. User manual 2020-12 | V01 | F.01U.385.759
2 System overview
When a connection is established, the Live page is initially displayed.
The application bar displays the following icons:
Live Click this icon to view the live video stream.
Playback Click this icon to play back recorded sequences.
This link is only visible if a storage medium has been
configured for recording. (With VRM recording, this
option is not active.)
Configuration Click this icon to configure the device.
Dashboard Click this icon to see detailed system information.
Links Click this icon to navigate to the Bosch download store.
Logout Click this icon to log out of the device.
Click this icon to get context-sensitive help for the page
you are browsing.
2.1 Live page
The Live page is used to display the live video stream and control the unit.
2.2 Playback
The Playback page is used for playing back recorded sequences.
2.3 Configuration
The Configuration page is used to configure the unit and the application interface.
Making Changes
Each configuration screen shows the current settings. You can change the settings by entering
new values or by selecting a predefined value from a list field.
Not every page has a Set button. Changes to pages without a Set button are set immediately.
If a page does show a Set button, you must click the Set button for a change to take effect.
i
Notice!
Save each change with the associated Set button.
Clicking the Set button saves the settings only in the current field. Changes in any other fields
are ignored.
Some changes only take effect after the unit is rebooted. In this case, the Set button changes
to Set and Reboot.
1. Make the desired changes.

8en | System overview FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor
2020-12 | V01 | F.01U.385.759 User manual Bosch Security Systems B.V.
2. Click the Set and Reboot button. The camera reboots and the changed settings are
activated.
2.4 Dashboard
The Dashboard page is used to display detailed information about the device.
The Dashboard is only visible in the application bar if the Show 'Dashboard' option is enabled
by a service-level user in the Configuration -> Web Interface -> Appearance page.

FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor Operation via the browser | en 9
Bosch Security Systems B.V. User manual 2020-12 | V01 | F.01U.385.759
3 Operation via the browser
3.1 Live page
After the connection is established, the Live page is initially displayed. It shows the live video
image on the right of the browser window. Depending on the configuration, various text
overlays may be visible on the live video image.
Other information may also be shown next to the live video image. The items shown depend
on the settings on the 'Live' functions page.
Connection
In the Connection group, you can configure the Stream option.
Image selection
To view a live stream:
1. On the left side of the browser, expand the Connection group if necessary.
2. Click the Stream drop-down arrow to see the options.
3. Select the stream you wish to view.
ROI
If Stream 2 is set to SD ROI, the ROI and Pre-positions groups become available.
– Navigate to Configuration -> Camera -> Encoder Streams
– Set Stream 2 to SD ROI
– Click Set to save the settings
– Go back to the Live page
– In the Connection group, click the Stream drop down arrow to see the options
– Select Stream 2
The ROI and Pre-positions groups are now enabled.
To use the ROI functionality, follow these steps:
– On the left side of the browser, expand the ROI group if necessary.
– Use the controls to move around the image.
– Click + to zoom and - to zoom out.
Pre-Positions
Six pre-position files can be defined for views generated by the region of interest (ROI)
controls.
1. On the left side of the browser, expand the Pre-positions group if necessary.
2. Use the ROI controls to define a particular view.
3. To store this view, click the icon of one of the six pre-position buttons.
– If a pre-position is already stored, a dialog box displays a message. Click OK to
overwrite or Cancel to cancel the operation
4. To recall a stored pre-position, click a pre-position button.
Digital I/O
Depending on the configuration of the unit, the alarm input and the output are displayed next
to the image. Expand the Digital I/O group if necessary.
The alarm symbol is for information and indicates the status of an alarm input:
– The symbol lights when the input alarm is active.
The alarm output allows the operation of an external device (for example, a light or a door
opener).
– To activate the output, click the checkmark symbol.
– The symbol lights when the output is activated.

10 en | Operation via the browser FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor
2020-12 | V01 | F.01U.385.759 User manual Bosch Security Systems B.V.
Recording status
The hard drive icon below the live camera image changes during an automatic recording.
The icon lights up and displays a moving graphic to indicate a running recording. If no
recording is taking place, a static icon is displayed.
Full-screen display
Click the full-screen icon to view the selected stream in full-screen mode; press Esc
on the keyboard to return to the normal viewing window.
Saving snapshots
Individual images from the displayed live video stream can be saved locally in JPEG format on
the computer's hard drive. The storage location depends on the configuration of the camera.
– Click the photo camera icon to save a single image.
Recording live video
Video sequences from the displayed live video stream can be saved locally on the computer's
hard drive. The sequences are recorded at the resolution specified in the encoder
configuration. The storage location depends on the configuration of the camera.
1. Click the recording icon to record video sequences.
– Saving begins immediately. The red dot on the icon indicates that a recording is in
progress.
2. Click the recording icon again to stop recording.
Start Video Security app
To start the Video Security app, click .
Show latest event
Click the Show latest event icon to watch the last recorded important events.
The Playback page opens.
Storage, CPU and network status
When accessing the unit with a browser, the local storage, processor and network status icons
are shown in the upper right of the window.
When a local storage card is available, the memory card icon changes color (green, orange or
red) to indicate the local storage activity. If you hover over this icon with the mouse the
storage activity is shown as a percentage.
If you hover over the middle icon, the CPU load is shown.
If you hover over the right-hand icon, the network load is shown.
This information can help with problem solving or when fine tuning the unit. For example:
– if the storage activity is too high, change the recording profile,
– if the CPU load is too big, change the VCA settings,
– if the network load is too big, change the encoder profile to reduce bitrate.

FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor Operation via the browser | en 11
Bosch Security Systems B.V. User manual 2020-12 | V01 | F.01U.385.759
Status icons
Various overlays in the video image provide important status information. The overlays provide
the following information:
Decoding error
The frame might show artifacts due to decoding errors.
Alarm flag
Indicates that an alarm has occurred.
Communication error
A communication error, such as a connection failure to the storage medium, a protocol
violation or a timeout, is indicated by this icon.
Gap
Indicates a gap in the recorded video.
Watermark valid
The watermark set on the media item is valid. The color of the check mark changes according
to the video authentication method that has been selected.
Watermark invalid
Indicates that the watermark is not valid.
Motion alarm
Indicates that a motion alarm has occurred.
Storage discovery
Indicates that recorded video is being retrieved.
3.2 Playback page
Click Playback in the application bar to view, search or export recordings. This link is
only visible when a direct iSCSI or memory card is configured for recording (with Video
Recording Manager (VRM) recording this option is not active).
On the left side of the screen, there are four groups:
–Connection
–Search
–Export
–Track list
3.2.1 Selecting the recording stream
On the left side of the browser, expand the Connection group if necessary.
To view a recording stream:
1. Click the Recording arrow to see the options.
2. Select recording stream 1 or 2.

12 en | Operation via the browser FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor
2020-12 | V01 | F.01U.385.759 User manual Bosch Security Systems B.V.
3.2.2 Searching for recorded video
On the left side of the browser, expand the Search group if necessary.
1. To limit the search to a particular time range, enter the date and times for the start and
stop points.
2. Select an option from the drop-down box to define a search parameter.
3. Click Search.
4. The results are shown.
5. Click a result to play it back.
6. Click Back to define a new search.
3.2.3 Exporting recorded video
On the left side of the browser, expand the Export group if necessary.
1. Select a track in the track list or in the search results (or click on the timeline below the
video window and drag the buttons to mark the sequence you want to export).
2. The start and stop date and time are filled-in for the selected track. If required, change
the times.
3. In the Time lapse drop-down box, select the original or a condensed speed.
4. In the Location drop-down box, select a target.
5. Click Export to save the video track.
Note:
The target server address is set on the Network / Accounts page.
3.2.4 Track list
The Track list shows all the available recordings.
3.2.5 Controlling playback
The time bar below the video image allows quick orientation. The time interval associated with
the sequence is displayed in the bar in gray. Arrows indicate the position of the image
currently being played back within the sequence.
The time bar offers various options for navigation in and between sequences.
– If required, click in the bar at the point in time at which the playback should begin.
– Change the time interval displayed by clicking the plus or minus icons or use the mouse
scroll wheel. The display can span a range from six months to one minute.
– Click the alarm jump buttons to go from one alarm event to the next or to the previous
one. Red bars indicate the points in time where alarms were triggered.
Controls
Control playback by means of the buttons below the video image.
The buttons have the following functions:
– Start/Pause playback
– Select the playback (forward or backward) speed using the speed regulator
– Step forward or backward frame-by-frame when paused (small arrows)
3.3 Dashboard
The Dashboard page shows information on 4 topics:
–Device status
–Recording status
–Connection Status
–Services
You can also download a .JSON file with information about the device:

FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor Operation via the browser | en 13
Bosch Security Systems B.V. User manual 2020-12 | V01 | F.01U.385.759
1. At the bottom of the page, locate the Export button
2. Click the Export button
3. Select a location in your hard drive to store the file

14 en | Configuration FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor
2020-12 | V01 | F.01U.385.759 User manual Bosch Security Systems B.V.
4 Configuration
4.1 General
4.1.1 Identification
Device name
Assign a unique name to assist in identification. This name simplifies the management of
multiple devices in more extensive systems.
The name is used for remote identification, for example, in the event of an alarm. Choose a
name that makes it as easy as possible to identify the location unambiguously.
Device ID
Each device should be assigned a unique identifier that can be entered here as an additional
means of identification.
Video name
Each video channel can be given a name. Click the + sign to add an extra line.
Host name
Enter the host name registered for the device.
Initiator extension
Add text to an initiator name to make identification easier in large iSCSI systems. This text is
added to the initiator name, separated from it by a full stop. (You can see the initiator name in
the System Overview page.)
Click Set to apply the changes.
4.1.2 User Management
A password prevents unauthorized access to the device. You can use different authorization
levels to limit access.
Proper password protection is only guaranteed when all higher authorization levels are also
protected with a password. Therefore, you must always start from the highest authorization
level when assigning passwords.
You can define and change a password for each authorization level if you are logged into the
“service” user account.
Authentication modes
The section Authentication modes provides information about the authentication modes set
in the camera. A checkmark appears in the checkbox to the left of the mode if the mode is set.
If the mode is not set, the phrase “No certificate installed” appears to the right of the mode
name.
This device has three authentication modes:
–Password indicates a password is set for the camera. It prevents unauthorized access to
the device, and can use different authorization levels to limit access.
Proper password protection is only guaranteed when all higher authorization levels are
also protected with a password. Therefore, you must always start from the highest
authorization level when assigning passwords.
You can define and change a password for each authorization level if you are logged into
the service user account.
–Certificate. A check mark in this check box indicates that at least one certificate is loaded
onto the device.
The Trusted certificate is a root certificate for Bosch Security Systems that proves that
the device meets the following criteria:

FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor Configuration | en 15
Bosch Security Systems B.V. User manual 2020-12 | V01 | F.01U.385.759
– It originates from a Bosch factory that is a secure environment.
– It has not been tampered with.
The Trusted certificate is issued by Escrypt. Escrypt is a Bosch company and Certificate
Authority (CA).
–Active Directory server (AD FS). A check mark in this check box indicates that the device
uses an active directory server.
Creating a new user
To create a new user, click Add in the section below Authentication modes.
In the box User, fill in the fields:
1. User name: Enter a name with a minimum of 5 and a maximum of 31 characters.
2. Group, select the appropriate authorization level:
– live is the lowest authorization level. At this level, it is only possible to view the live
video image, and switch between the different live image displays.
– user is the middle authorization level. At this level, it is possible to operate the
device and playback recordings, but configuration changes are not possible.
– service is the highest authorization level. Entering the correct password gives access
to all the functions, and allows all configuration settings to be changed.
3. Type, select either:
–Password for a new password.
Use a minimum of 8 and a maximum of 19 characters. The password must have
upper-case and lower-case letters, one or more numerical digits and one or more of
these special characters ! ? ” # $ % ( ) { } [ ] * - = . , ; ^ _ | ~ \
Special characters such as space @ : < > ‘ & + are not valid.
In this case, enter the new password a second time to eliminate typing mistakes.
–Certificate for a certificate that the new user is authorized to use.
4. Click Set to confirm and create a new user.
4.1.3 Date/Time
Date format
Select the required date format.
Device date/Device time
If there are multiple devices operating in your system or network, it is important to
synchronize their internal clocks. For example, it is only possible to identify and correctly
evaluate simultaneous recordings when all devices are operating on the same time.
1. Enter the current date. Since the device time is controlled by the internal clock, it is not
necessary to enter the day of the week – it is added automatically.
2. Enter the current time or click Sync to PC to apply the system time from your computer
to the device.
Note:
It is important that the date/time is correct for recording. An incorrect date/time setting could
prevent correct recording.
Device time zone
Select the time zone in which the system is located.

16 en | Configuration FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor
2020-12 | V01 | F.01U.385.759 User manual Bosch Security Systems B.V.
Daylight saving time
The internal clock can switch automatically between normal and daylight saving time (DST).
The unit already contains the data for DST switch-overs for many years in advance. If the date,
time and zone have been set up correctly, a DST table is automatically created.
If you decide to create alternative daylight saving time dates by editing the table, note that
values occur in linked pairs (DST start and end dates).
First, check the time zone setting. If it is not correct, select the appropriate time zone and
click Set.
1. Click Details to edit the DST table.
2. Click Generate to fill the table with the preset values from the unit.
3. Click one of the entries in the table to make changes. The entry is highlighted.
4. Click Delete to remove the entry from the table.
5. Choose other values from the list boxes under the table, to change the selected entry.
Changes are immediate.
6. If there are empty lines at the bottom of the table, for example after deletions, add new
data by marking the row and selecting values from the list boxes.
7. When finished, click OK to save and activate the table.
Time server address
The unit can receive the time signal from a time server using various time server protocols and
then use it to set the internal clock. The device polls the time signal automatically once every
minute.
Enter the IP address of a time server.
Overwrite by DHCP
Select this checkbox to have the DHCP server give the time server date.
Time server type
– Select Time protocol if the server uses the RFC 868 protocol.
– Select the protocol that is supported by the selected time server. It is recommended to
select the SNTP protocol. This protocol provides high accuracy and is required for special
applications and future function extensions.
– Select the TLS protocol if the server uses the RFC 5246 protocol.
Click Set to apply the changes.
4.1.4 Display Stamping
Various overlays or stamps in the video image provide important supplementary information.
These overlays can be enabled individually and arranged on the image in a clear manner.
Camera name stamping
Select the position of the camera name overlay in the drop-down box. It can be displayed at
the Top, at the Bottom, or at a position of choice using the Custom option, or it can be set to
Off for no overlay information.
If the Custom option is selected, enter values in the X and Y position fields.
Optionally, tick the Underlay with full-width bar box to place a full-width background-bar
beneath the time stamp.
Logo
To place a logo on the image, select and upload an uncompressed .bmp file with a maximum
size of 300x300 pixels and 256 colors to the camera. Its position on the image can then be
selected.

FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor Configuration | en 17
Bosch Security Systems B.V. User manual 2020-12 | V01 | F.01U.385.759
Logo position
This option becomes available when the Camera name stamping option is enabled. Select:
–Off : This option is disabled.
–To the left of the name: The logo will be positioned to the left of the Camera name
stamping
–To the right of the name: The logo will be positioned to the right of the Camera name
stamping
–Logo only: The logo will be shown without the Camera name stamping.
Time stamping
Select the position of the time and date overlay in the drop-down box. It can be displayed at
the Top, at the Bottom, or at a position of choice using the Custom option, or it can be set to
Off for no overlay information.
If the Custom option is selected, enter values in the X and Y position fields.
Display milliseconds
If necessary, display milliseconds for Time stamping. This information can be useful for
recorded video images; however, it does increase the processor's computing time. Select Off
if displaying milliseconds is not needed.
Live video indicator
Select On to display the Live video indicator, an icon that pulses on the OSD to show that the
video stream is live.
Select Off to hide the Live video indicator.
Alarm mode stamping
Select On in the drop-down box for a text message to be displayed in the event of an alarm. It
can be displayed at a position of choice using the Custom option, or it can be set to Off for no
overlay information.
If the Custom option is selected, enter values in the X and Y position fields.
Alarm message
Enter the message to be displayed on the image in the event of an alarm. The maximum text
length is 31characters.
Transparent background
Check this box to make transparent the stamp background on the image.
Text color
Select the color for the alarm message to be displayed in.
Background color
Select the background color for the alarm message to be displayed in.
If you have enabled the Transparent background option, the background color is not
displayed in the OSD.
Stamping size
Select the desired font size of the overlays on the OSD: Normal or Large.
Video authentication
Select from the Video authentication drop-down box a method for verifying the integrity of
the video.
If you select Watermarking, all images are marked with an icon. The icon indicates if the
sequence (live or saved) has been manipulated.
If you want to add a digital signature to the transmitted video images to ensure their integrity,
select one of the cryptographic algorithms for this signature.

18 en | Configuration FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor
2020-12 | V01 | F.01U.385.759 User manual Bosch Security Systems B.V.
Signature interval [s]
For certain Video authentication modes, enter the interval (in seconds) between insertions of
the digital signature.
Click Set to apply the changes.
4.1.5 GB/T 28181
This page allows you to set the parameters for conformance to the GB/T28181 national
standard “Security and protection video monitoring network system for information transport,
switch and control”. This standard is specifically for China.
Enable
Select this checkbox to enable the system to use the other parameters on this page in
accordance with the GB/T 28181 national standard.
H.264 elementary stream
Select this checkbox to select or to enable the H.264 elementary stream.
Registration timeout
Enter a value (in milliseconds) for the registration timeout. The default is 3600.
Heartbeat timeout
Enter the value (in seconds) for the heartbeat timeout. The default is 15.
Server ID
Enter the ID of the server.
Server IP address
Enter the server IP address.
Server port
Enter the number of the server port. The default is 0.
Device ID
Enter the ID of the device.
Device port
Enter the number of the device port. The default is 5060.
Password
Enter the appropriate password.
Alarm device ID
Enter the ID of the alarm device.
Click Set to apply the changes.
4.2 Web Interface
4.2.1 Appearance
You can adapt the appearance of the web interface and change the website language to meet
your requirements.
You can use GIF or JPEG images to replace the company and device logos. The image can be
stored on a web server.
Make sure that a connection to the web server is always available to display the image. The
image files are not stored on the device.
To use the original graphics, delete the entries in the Company logo and Device logo fields.
Website language
Select the language for the user interface.

FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor Configuration | en 19
Bosch Security Systems B.V. User manual 2020-12 | V01 | F.01U.385.759
Company logo
To replace the company's logo in the top-right part of the window, enter the path to a suitable
image in this field. The image file must be stored on a web server.
Device logo
To replace the device name in the top-left part of the window, enter the path to a suitable
image in this field. The image file must be stored on a web server.
Show VCA metadata
When video content analysis (VCA) is activated, additional information is displayed in the live
video stream. With the MOTION+ analysis type, for example, the sensor fields in which motion
is recorded are marked with yellow rectangles.
Using EssentialVideoAnalytics, the outlines of detected objects are displayed in following
colors:
– Red: Objects that generate an alarm event under the current settings appear on the
camera image inside a red outline.
– Orange: An object that has triggered one alarm event but does not generate another
appears inside an orange outline (example: object has crossed a line). During forensic
search, an object that triggers an alarm event has an orange outline from the beginning.
– Yellow: Objects that are detected as moving but do not generate an alarm event under
the current settings appear inside a yellow outline.
Show VCA trajectories
When video content analysis (VCA) is activated, check this item to show additional information
that traces the path of objects, if the corresponding analysis type provides this data.
Show overlay icons
Select this check box to show overlay icons on the live video image.
Show VCA items
Select this checkbox to show VCA items on the live video image.
Shows alarm fields, lines and routes configured for the video analytics in the following colors:
– Green: Fields, lines and routes used in a task are displayed in green. They can be edited
but not deleted.
– Red: Fields, lines and routes currently in alarm mode are displayed in red.
Show 'Dashboard'
Select this checkbox to enable the Dashboard in the application bar.
Secure cookies
Select this checkbox to secure the cookies sent through the camera.
i
Notice!
If cookies are secured, authentication forwarding to MPEG ActiveX and the Video Security
App is prohibited.
Video player
Select the type of player to be used for live mode viewing.
Latency mode
Select the required latency mode:
–Low delay: Default mode. Provides marginal buffering to display fluent video under
normal network conditions.
–Smooth video: Allows the buffer to automatically adjust to cover network jitter, inducing
higher latency.

20 en | Configuration FLEXIDOME IP micro 3000i - outdoor | FLEXIDOME
IP turret 3000i IR - outdoor
2020-12 | V01 | F.01U.385.759 User manual Bosch Security Systems B.V.
–No buffering: Shows video as it is received by the decoder with minimum latency. Allows
the video to jerk if there is network jitter.
Video buffer
The value shown is calculated from the Latency mode setting. It cannot be changed.
JPEG resolution
You can specify the size of the JPEG image on the Live page. Options are Small, Medium,
Large, 720p, 1080p, and “Best possible” (default).
JPEG interval
You can specify the interval at which the individual images should be generated for the M-
JPEG image on the Live page.
JPEG quality
You can specify the quality at which the JPEG images appear on the Live page.
Click Set to apply the changes.
4.2.2 'Live' functions
You can adapt the Live page functions to meet your requirements. Choose from a variety of
different options for displaying information and controls.
1. Select the check boxes for the functions to be displayed on the Live page. The selected
elements are checked.
2. Check to see if the desired items are shown.
Transmit audio
When selected, the audio from the camera (if set to On on the Audio page) is sent to the
computer. This setting applies only to the computer on which the selection is made.
Transmitting audio data requires additional network bandwidth.
Lease time [s]
The lease time in seconds determines the time beyond which a different user is authorized to
control the camera after no further control signals are received from the current user. After
this time interval, the camera is automatically available for another user.
Auto logout time [min]
Set a time frame (in minutes) for the automatic logout. Default value is 0 (no automatic
logout).
Show alarm inputs
The alarm inputs are displayed next to the video image as icons along with their assigned
names. If an alarm is active, the corresponding icon changes color.
Show alarm outputs
Alarm outputs are shown next to the video image as icons along with their assigned names. If
an output is switched, the icon changes color.
Allow snapshots
Specify whether the icon for saving individual images should be displayed below the live
image. Individual images can only be saved if this icon is visible.
Allow local recording
Specify whether the icon for saving video sequences locally should be displayed below the live
image. Video sequences can only be saved locally on your hard disk if this icon is visible.
I-frames-only stream
When this checkbox is enabled, the I-frames stream option on the Connection tab of the Live
page becomes available.