Bosch VBN-5085 User manual

DINION 5000 AN
VBN-5085
en Installation Manual

DINION 5000 AN Table of Contents | en 3
Bosch Security Systems Installation Manual AM18-Q0644 | v1.0 | 2013.03
Table of Contents
1Safety 5
1.1 Safety precautions 5
1.2 System ground/Safety ground 5
1.3 Important safety instructions 6
1.4 Important notices 7
1.5 FCC information 8
1.6 UL certification 9
1.7 Bosch notice 9
2 Introduction 10
2.1 Features 10
3 Installation 11
3.1 Unpacking 11
4 Connection and mounting 12
4.1 Power connection 12
4.1.1 Low voltage cameras 12
4.1.2 High voltage cameras 13
4.2 Video connections 14
4.2.1 Output Video signal 14
4.3 Alarm and relay connector 15
4.4 Lens mounting 16
4.5 Back focus adjustment 17
4.6 Mounting the camera 19
5 Configuration 20
5.1 Menus 20
5.1.1 Top level menus 20
5.1.2 Menu navigation 21
5.2 Pre-defined modes 22
5.3 Day/Night switching 23
5.4 Camera control communication (Bilinx) 23
5.5 Main menu structure 24
5.5.1 Mode submenu 24

4en | Table of Contents DINION 5000 AN
AM18-Q0644 | v1.0 | 2013.03 Installation Manual Bosch Security Systems
5.5.2 Exposure submenu 25
5.5.3 Day/Night submenu 27
5.5.4 Enhance / Dynamic Engine submenu 29
5.5.5 Color submenu 31
5.5.6 VMD submenu 32
5.5.7 Image Adjustment submenu 33
5.6 Install menu structure 34
5.6.1 Language submenu 35
5.6.2 Lens Wizard submenu 35
5.6.3 Synchronization submenu 37
5.6.4 Alarm I/O submenu 38
5.6.5 Connections submenu 39
5.6.6 Test signal submenu 39
5.6.7 Camera ID submenu 40
5.6.8 Privacy masking submenu 41
5.6.9 Flip submenu 41
5.6.10 Defaults submenu 42
6Troubleshooting 43
6.1 Resolving problems 43
6.2 Customer service 44
7 Maintenance 45
7.1 Repairs 45
7.1.1 Transfer and disposal 45
8 Technical Data 46
8.1 Specifications 46
8.1.1 Dimensions 48
8.1.2 Accessories 49

DINION 5000 AN Safety | en 5
Bosch Security Systems Installation Manual AM18-Q0644 | v1.0 | 2013.03
1Safety
1.1 Safety precautions
1.2 System ground/Safety ground
System (video) ground is indicated by the symbol .
Safety (power) ground is indicated by the symbol .
The system ground is only used to comply with safety standards
or installation practices in certain countries. Bosch does not
recommend connecting system ground to safety ground unless
it is explicitly required. However, if the system ground and
safety ground are connected and grounding loops are causing
interference in the video signal, use an isolation transformer
(available separately from Bosch).
DANGER!
High risk: This symbol indicates an imminently hazardous
situation such as "Dangerous Voltage" inside the product.
If not avoided, this will result in an electrical shock, serious
bodily injury, or death.
WARNING!
Medium risk: Indicates a potentially hazardous situation.
If not avoided, this could result in minor or moderate bodily
injury.
CAUTION!
Low risk: Indicates a potentially hazardous situation.
If not avoided, this could result in property damage or risk of
damage to the unit.
CAUTION!
Connecting System ground to Safety ground may result in
ground loops that can disrupt the CCTV system.

6en | Safety DINION 5000 AN
AM18-Q0644 | v1.0 | 2013.03 Installation Manual Bosch Security Systems
1.3 Important safety instructions
Read, follow, and retain for future reference all of the following
safety instructions. Heed all warnings on the unit and in the
operating instructions before operating the unit.
1. Cleaning - Generally, using a dry cloth for cleaning is
sufficient but a moist, fluff-free cloth or leather shammy
may also be used. Do not use liquid cleaners or aerosol
cleaners.
2. Heat Sources - Do not install the unit near any heat
sources such as radiators, heaters, stoves, or other
equipment (including amplifiers) that produce heat.
3. Water - Never spill liquid of any kind on the unit.
4. Lightning - Take precautions to protect the unit from
power and lightning surges.
5. Controls adjustment - Adjust only those controls specified
in the operating instructions. Improper adjustment of
other controls may cause damage to the unit.
6. Power sources - Operate the unit only from the type of
power source indicated on the label.
7. Servicing - Unless qualified, do not attempt to service this
unit yourself. Refer all servicing to qualified service
personnel.
8. Replacement parts - Use only replacement parts specified
by the manufacturer.
9. Installation - Install in accordance with the manufacturer's
instructions and in accordance with applicable local codes.
10. Attachments, changes or modifications - Only use
attachments/accessories specified by the manufacturer.
Any change or modification of the equipment, not
expressly approved by Bosch, could void the warranty or,
in the case of an authorization agreement, authority to
operate the equipment.

DINION 5000 AN Safety | en 7
Bosch Security Systems Installation Manual AM18-Q0644 | v1.0 | 2013.03
1.4 Important notices
Disposal - Your Bosch product was developed and
manufactured with high-quality material and components that
can be recycled and reused. This symbol means that
electronic and electrical appliances, which have reached the
end of their working life, must be collected and disposed of
separately from household waste material. Separate collecting
systems are usually in place for disused electronic and
electrical products. Please dispose of these units at an
environmentally compatible recycling facility, per European
Directive 2002/96/EC
WARNING!
Power disconnect for high voltage versions: A unit has power
supplied whenever the power cord is inserted into the power
source. The power cord plug is the main power disconnect for
the unit. For pluggable equipment, install the socket outlet near
the equipment so it is easily accessible.
WARNING!
All-pole power switch: Incorporate an all-pole power switch,
with a contact separation of at least 3 mm in each pole, into the
electrical installation of the building.
CAUTION!
Fuse rating: The branch circuit protection must be secured with
a maximum fuse rating of 16 A. This must be in accordance with
NEC800 (CEC Section 60).
CAUTION!
The Low Voltage power supply unit must comply with EN/UL
60950. The power supply must be a SELV-LPS unit or a SELV -
Class 2 unit (Safety Extra Low Voltage - Limited Power Source).

8en | Safety DINION 5000 AN
AM18-Q0644 | v1.0 | 2013.03 Installation Manual Bosch Security Systems
1.5 FCC information
FCC & ICES Information
(U.S.A. and Canadian Models Only)
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
– reorient or relocate the receiving antenna;
– increase the separation between the equipment and
receiver;
– connect the equipment into an outlet on a circuit different
from that to which the receiver is connected;
– consult the dealer or an experienced radio/TV technician
for help.
Intentional or unintentional modifications, not expressly
approved by the party responsible for compliance, shall not be
made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult
the dealer or an experienced radio/television technician for
corrective action.
The user may find the following booklet, prepared by the
Federal Communications Commission, helpful: How to Identify
and Resolve Radio-TV Interference Problems. This booklet is
available from the U.S. Government Printing Office,
Washington, DC 20402, Stock No. 004-000-00345-4.

DINION 5000 AN Safety | en 9
Bosch Security Systems Installation Manual AM18-Q0644 | v1.0 | 2013.03
1.6 UL certification
Disclaimer
Underwriter Laboratories Inc. ("UL") has not tested the
performance or reliability of the security or signaling aspects of
this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UL's Standard(s) for Safety for Information
Technology Equipment, UL 60950-1. UL Certification does not
cover the performance or reliability of the security or signaling
aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR
CERTIFICATIONS WHATSOEVER REGARDING THE
PERFORMANCE OR RELIABILITY OF ANY SECURITY OR
SIGNALING-RELATED FUNCTIONS OF THIS PRODUCT.
1.7 Bosch notice
More information
For more information please contact the nearest Bosch Security
Systems location or visit www.boschsecurity.com

10 en | Introduction DINION 5000 AN
AM18-Q0644 | v1.0 | 2013.03 Installation Manual Bosch Security Systems
2 Introduction
2.1 Features
The DINION 5000 Day/Night WDR camera is a high-
performance, smart, surveillance color camera. It uses a wide
dynamic range 960H CCD sensor for outstanding picture
performance.
The camera is easy to install and ready to use, and offers the
best solution for demanding scene conditions. Features
include:
– 1/3-inch 960H CCD sensor with wide dynamic range
– True Day/Night performance with switchable IR filter
– 720TVL sensor resolution
– High Dynamic Range
– Privacy zones
– Detail enhancement
– Bilinx (bi-directional coaxial communication)
– Wide operating temperature range
–Lenswizard
– Six pre-programmed operation modes
– Dynamic noise reduction
– Multiple language on-screen display
– Built-in test pattern generator

DINION 5000 AN Installation | en 11
Bosch Security Systems Installation Manual AM18-Q0644 | v1.0 | 2013.03
3 Installation
3.1 Unpacking
Unpack carefully and handle the equipment with care.
The packaging contains:
– DINION 5000 camera
– CCD protection cap (mounted on camera)
– Alarm I/O connector
– Power connector
– Important safety instructions
– Quick install instructions
– CD-ROM
– Installation instructions
If equipment has been damaged during shipment, repack it in
the original packaging and notify the shipping agent or supplier.
WARNING!
Installation should only be performed by qualified service
personnel in accordance with the National Electrical Code
NEC800 (CEC Section 60) or applicable local codes.
CAUTION!
The camera module is a sensitive device and must be handled
carefully.

12 en | Connection and mounting DINION 5000 AN
AM18-Q0644 | v1.0 | 2013.03 Installation Manual Bosch Security Systems
4 Connection and mounting
4.1 Power connection
4.1.1 Low voltage cameras
Figure 4.1 Low voltage power connection
Connect power from a 24 VAC or 12 VDC class 2 power supply
as follows:
– Use AWG16 to 22 stranded wire or AWG16 to 26 solid
wire; cut back 5 mm (0.2 in) of insulation.
– Remove the 3-pole connector from the camera body.
– Loosen the screws and insert the wires.
Note
The central connection for System (video) ground is
optional. Connecting System ground to Safety ground may
result in ground loops that can disrupt the CCTV system.
– Tighten the screws and reconnect the 3-pole connector to
the camera.
CAUTION!
Before proceeding, disconnect the power from the power
supply cable. Ensure that the voltage of the unit matches the
voltage and type of the power supply being used.
12 VDC
24 VAC
VIDEO
+
ALARM
1
2
3
4
5
6
5 mm

DINION 5000 AN Connection and mounting | en 13
Bosch Security Systems Installation Manual AM18-Q0644 | v1.0 | 2013.03
Note
For a DC supply the polarity is important. Incorrect polarity
does not damage the camera but it will not switch on. For an
AC supply maintain a consistent wiring polarity in multiple
camera systems to help avoid potential camera video rolling.
4.1.2 High voltage cameras
Figure 4.2 High voltage power connection
Connect the power cable of a high voltage camera to a 230 VAC
power supply outlet.
VIDEO
ALARM
1
2
3
4
5
6

14 en | Connection and mounting DINION 5000 AN
AM18-Q0644 | v1.0 | 2013.03 Installation Manual Bosch Security Systems
4.2 Video connections
Figure 4.3 BNC connectors
4.2.1 Output Video signal
The camera has a BNC connector to connect the video coax
cable with a male BNC connector. A UTP adapter (VDA-455UTP)
is available as an optional accessory to allow a UTP video cable
to be connected to the BNC connector.
VIDEO
ALARM
1
2
3
4
5
6
Video BNC

DINION 5000 AN Connection and mounting | en 15
Bosch Security Systems Installation Manual AM18-Q0644 | v1.0 | 2013.03
4.3 Alarm and relay connector
Figure 4.4 Alarm and relay connector pins
– Max. wire diameter AWG 22-28 for both stranded and
solid; cut back 5 mm (0.2 in) of insulation.
– Alarm output relay switching capability: Max voltage 30VAC
or +40 VDC. Max 0.5 A continuous, 10 VA.
– Alarm in: TTL logic, +5V nominal, +40 VDC max, DC coupled
with 22 kOhm pull-up to +3.3 V.
– Alarm in: configurable as active low or active high.
– Max. 42 V allowed between camera ground and each of the
relay pins.
Pin Alarm socket
1 Alarm in
2notused
3 Relay out contact 2
4 Alarm in ground
5notused
6 Relay out contact 1
ALARM
1
2
3
4
5
6
5 mm
(0.2 in)

16 en | Connection and mounting DINION 5000 AN
AM18-Q0644 | v1.0 | 2013.03 Installation Manual Bosch Security Systems
4.4 Lens mounting
The camera accepts CS-mount lenses. C-mount lenses can be
mounted using the lens adapter ring. DC-iris lenses are
recommended for the best picture performance.
Note
If a short circuit is detected on the lens connector, the on-
screen display (OSD) failure message LENS SHORT CIRCUIT is
shown. The lens circuit is automatically disabled to avoid
internal damage. Remove the lens connector and check the pin
connections.
CAUTION!
To avoid damaging the CCD sensor when using a C-mount lens,
make sure the supplied lens adapter ring is mounted onto the
camera before mounting the lens.
Lenses weighing more than 0.5 kg (1.1lbs) must be separately
supported.
Figure 4.5 Mounting a lens Figure 4.6 Lens connector
Pin DC iris lens
1Damp-
2Damp+
3Drive+
4Drive-
Bosch
Bosch

DINION 5000 AN Connection and mounting | en 17
Bosch Security Systems Installation Manual AM18-Q0644 | v1.0 | 2013.03
4.5 Back focus adjustment
To optimize picture sharpness in both bright and low-level
lighting, adjust the back focus. Use the camera's unique Lens
Wizard. This ensures that the object of interest always remains
in focus, even when focusing at the maximum lens iris opening
(for example, at night).
– When back focusing varifocal lenses, adjust to obtain a
sharp picture in both wide-angle and tele positions for
both far and near focus.
– When back focusing zoom lenses, ensure the object of
interest remains in focus throughout the entire zoom range
of the lens.
To adjust back focus:
1. Open the slide door panel at the side of the camera.
1. Unlock the back focus locking button.
2. Press and hold the center key for more than 1 second until
the Install menu appears.
3. Select Len Wizard and move cursor to the Set Back Focus
Now item.
4. Turn the back focus adjustment as required.
Bosch

18 en | Connection and mounting DINION 5000 AN
AM18-Q0644 | v1.0 | 2013.03 Installation Manual Bosch Security Systems
5. Lock the back focus locking button.
6. Press and hold the center key for more than 1 second until
all the menus disappear.
7. Close the side door panel.
Bosch
Bosch

DINION 5000 AN Connection and mounting | en 19
Bosch Security Systems Installation Manual AM18-Q0644 | v1.0 | 2013.03
4.6 Mounting the camera
The camera can be mounted either from the top or from the
bottom (1/4" 20 UNC thread). The bottom mounting is isolated
from ground to prevent ground loops.
Figure 4.7 Mounting a camera
Note:
A wide range of accessories is available for indoor and outdoor
mounting.
CAUTION!
Do not point the camera/lens into direct sunlight as this may
damage the sensors.

20 en | Configuration DINION 5000 AN
AM18-Q0644 | v1.0 | 2013.03 Installation Manual Bosch Security Systems
5 Configuration
The camera normally provides an optimal picture without the
need for further adjustments. Advanced set-up options are
available in a menu system for getting the best results under
special circumstances.
The camera implements your changes immediately so that
before and after settings are easily compared.
5.1 Menus
5.1.1 Top level menus
There are two upper level menus: a Main menu and an Install
menu. The menus have functions that can be selected directly
or submenus for more detailed set-up.
– To access the Main menu, press the menu/select button
(center) for less than 1 second. The Main menu appears on
the monitor. The Main menu allows you to select and set-
up the picture enhancement functions. If you are not happy
with your changes, you can always recall the default values
for the mode.
– The camera also has an Install menu in which the
installation settings can be set. To access the Install menu,
press the menu/select button (center) for longer than 2
seconds.