BOSER Technology HS-7165 User manual

HS-7165
Intel® Mobile Dual-Core processor
PICMG1.3 Full-size SBC
•1066/800MHz FSB•CompactFlash•
•DVI-I/CRT/LVDS•Dual GB LAN•
•Audio•SATA•RS-232/422/485•4 COM•
•7 USB2.0•WDT•H/W Monitor•

Copyright Disclaimers
The accuracy of contents in this manual has passed thorough checking and review before
publishing. BOSER Technology Co., Ltd., the manufacturer and publisher, is not liable for
any infringements of patents or other rights resulting from its use. The manufacturer will
not be responsible for any direct, indirect, special, incidental or consequential
damages arising from the use of this product or documentation, even if advised of
the possibility of such damage(s).
This manual is copyrighted and BOSER Technology Co., Ltd. reserves all
documentation rights. Unauthorized reproduction, transmission, translation, and
storage of any form and means (i.e., electronic, mechanical, photocopying, recording)
of this document, in whole or partly, is prohibited, unless granted permission by BOSER
Technology Co., Ltd.
BOSER Technology Co., Ltd. reserves the right to change or improve the contents of
this document without due notice. BOSER Technology Co., Ltd. assumes no
responsibility for any errors or omissions that may appear in this manual, nor does
it make any commitment to update the information contained herein.
T
T
Tr
r
ra
a
ad
d
de
e
em
m
ma
a
ar
r
rk
k
ks
s
s
BOSER is a registered trademark of BOSER Technology Co., Ltd.
ISB is a registered trademark of BOSER Technology Co., Ltd.
Intel is a registered trademark of Intel Corporation.
Award is a registered trademark of Award Software, Inc.
AMI is a registered trademark of AMI Software, Inc.
All other trademarks, products and or product names mentioned herein are
mentioned for identification purposes only, and may be trademarks and/or
registered trademarks of their respective companies or owners.
© Copyright 2010 BOSER Technology Co., Ltd.
All Rights Reserved.
Edition 1.3, October 06, 2010

Table of Contents
Chapter 1 General Description ..................................1
1.1 Major Features....................................................................... 2
1.2 Specifications ........................................................................ 2
1.3 Board Dimensions................................................................. 4
Chapter 2 Unpacking ..................................................5
2.1 Opening the Delivery Package............................................. 5
2.2 Inspection............................................................................... 5
Chapter 3 Hardware Installation ..............................7
3.1 Before Installation ................................................................. 7
3.2 Board Layout ......................................................................... 8
3.3 Jumper List ............................................................................ 9
3.4 Connector List ....................................................................... 9
3.5 Configuring the CPU ........................................................... 10
3.6 System Memory ................................................................... 10
3.7 VGA Controller .................................................................... 10
3.8 Serial ATA Connector ......................................................... 13
3.9 Serial Port Connectors ....................................................... 13
3.10 Ethernet Connector............................................................. 15
3.11 USB Port............................................................................... 15
3.12 CMOS Data Clear................................................................. 16
3.13 Parallel Port.......................................................................... 16
3.14 Power and Fan Connectors................................................ 17
3.15 Keyboard/Mouse Connectors ............................................ 17
3.16 System Front Panel Control ............................................... 18
Connector CN16 Orientation.................................................................................18
3.17 Watchdog Timer .................................................................. 18
3.18 Audio Connectors ............................................................... 20
3.19 External PCIe Slot ............................................................... 21
3.20 CompactFlashConnector................................................ 21
3.21 8-bit GPIO Function............................................................. 23

Chapter 4 AMI BIOS Setup..................................... 25
4.1 Starting Setup...................................................................... 25
4.2 Using Setup ......................................................................... 26
4.3 Main Menu............................................................................ 27
4.4 Advanced Settings .............................................................. 28
4.5 Advanced PCI/PnP Settings............................................... 31
4.6 Boot Settings ....................................................................... 32
4.7 Security Settings ................................................................. 33
4.8 Advanced Chipset Settings................................................ 34
4.9 Exit Options ......................................................................... 35
Chapter 5 Software Utilities.....................................37
5.1 Chipset Driver Installation.................................................. 37
5.2 VGA Driver Installation ....................................................... 40
5.3 LAN Driver Installation........................................................ 43
5.4 Audio Driver Installation..................................................... 45

Declaration of Conformity -- CE Mark
BOSER Technology hereby acknowledges that compliance testing in
accordance with applicable standards of the EU’s EMC Directive,
89/336/EEC, was successfully completed on a sample of the equipment
identified below:
Equipment Class: Information Technology Equipment
Product Model Series: HS-7165
This Product Complies With: EN55022: Class A for Radiated emissions
EN50082-2: Heavy Industrial EMC Immunity
We, the undersigned, hereby declare that the equipment specified above
conforms to the above directives and standards.
Manufacturer:
BOSER TECHNOLOGY CO., LTD.

Safety Instructions
Integrated circuits on computer boards are sensitive to static electricity. To
avoid damaging chips from electrostatic discharge, observe the following
precautions:
Do not remove boards or integrated circuits from their anti-static packaging
until you are ready to install them.
Before handling a board or integrated circuit, touch an unpainted portion of
the system unit chassis for a few seconds. This helps to discharge any static
electricity on your body.
Wear a wrist-grounding strap, available from most electronic component
stores, when handling boards and components. Fasten the ALLIGATOR clip
of the strap to the end of the shielded wire lead from a grounded object.
Please wear and connect the strap before handle the HS-7165 to ensure
harmlessly discharge any static electricity through the strap.
Please use an anti-static pad when putting down any components or parts or
tools outside the computer. You may also use an anti-static bag instead of
the pad. Please inquire from your local supplier for additional assistance in
finding the necessary anti-static gadgets.
NOTE: DO NOT TOUCH THE BOARD OR ANY OTHER SENSITIVE
COMPONENTS WITHOUT ALL NECESSARY ANTI-STATIC
PROTECTIONS.

1
Chapter 1
General Description
The HS-7165 is an Intel® GM45/ICH9-M chipset-based board
designed, the board supports Intel® Mobile Dual-Core processor. The
HS-7165 is an ideal all-in-one PICMG1.3 single board computer.
Additional features include an enhanced I/O with CF, DVI-I/CRT/LVDS,
dual GB LAN, audio, SATA, 4 COM, and 7 USB2.0 interfaces.
The Intel® GM45 integrated Intel® Gen5.0 GMA 4500MHD Graphics
shared system memory up to 352MB with DVMT5.0 supports
CRT/Panel displays up to 2048 x 1536. It also supports 24-bit
single/dual channel LVDS interface.
System memory is also sufficient with the two 240-pin DIMM sockets
up to 4GB DDR2 SDRAM.

2
Additional onboard connectors include seven advanced USB2.0 ports
providing faster data transmission. And two RJ-45 connectors for
10/100/1000 Based Ethernet uses. To ensure the reliability in an
unmanned or standalone system, the watchdog timer (WDT) onboard
HS-7165 is designed with software that does not need the arithmetical
functions of a real-time clock chip. If any program causes unexpected
halts to the system, the onboard WDT will automatically reset the CPU
or generate an interrupt to resolve such condition.
1.1 Major Features
The HS-7165 comes with the following features:
¾Socket P for Intel® Mobile Dual-Core processor, supports
1066/800/667MHz FSB
¾2 x DIMMs up to 4GB DDR2 SDRAM
¾Intel® GM45/ICH9-M system chipset
¾Intel® GM45 integrated VGA for CRT & LVDS
¾2 x 10/100/1000 Mbps Ethernet
¾High Definition audio codec
¾Supports CF, 4 x SATA, 4 x COM, 7 x USB2.0
¾Supports 24-bit LVDS, 8-bit GPIO, H/W Monitor function
¾Option for DVI-I display
1.2 Specifications
zSystem
CPU:
Intel® Mobile Dual-Core processor, supports Merom 65nm and Penryn
45nm (Socket P)
FSB:
1066/800/667MHz FSB
BIOS:
AMI PnP Flash BIOS
System Chipset:
Intel® GM45/ICH9-M
I/O Chipset:
Winbond W83627UHG
System Memory:
2 x 240-pin DIMM sockets DDR2 800MHz up to 4GB
Storage:
1 x Type II CF socket
Watchdog Timer:
Software programmable time-out intervals from 1~255 sec. or 1~255min.

3
H/W Status Monitor:
Monitoring temperatures, voltages, and cooling fan status
Power Function
Supports ATX power mode
Operating Temperature
0~60 degrees C
Operating Humidity
0~95%, non-condensing
Size (L x W)
338 x 126 mm
zI/O Interface
MIO:
3 x RS-232
1 x RS-232/422/485
7 x USB2.0 (6 x internal, 1 x external)
1 x Parallel
4 x SATA
1 x 6-pin header for PS/2 KB/MS
GPIO:
8-bit general purpose input/output port
zDisplay
Chipset:
Intel® GM45 integrated Intel® GMA 4500MHD
Display Memory:
Shared system memory up to 352MB with DVMT5.0
LVDS:
24-bit single/dual channel
DVI Chipset:
Integrated Intel® GMA 4500MHD
Resolution:
2048 x 1536 @ 60Hz
zAudio
Chipset:
RealTek ALC262 High Definition audio codec
Audio Interface (w/pin header):
MIC In, Line Out
zEthernet
Chipset:
Dual RealTek RTL8111C 10/100/1000 Mbps LAN
Ethernet Interface:
2 x RJ-45

4
1.3 Board Dimensions

5
Chapter 2
Unpacking
2.1 Opening the Delivery Package
The HS-7165 is packed in an anti-static bag. The board has
components that are easily damaged by static electricity. Do not
remove the anti-static wrapping until proper precautions have been
taken. Safety Instructions in front of this manual describe anti-static
precautions and procedures.
2.2 Inspection
After unpacking the board, place it on a raised surface and carefully
inspect the board for any damage that might have occurred during
shipment. Ground the board and exercise extreme care to prevent
damage to the board from static electricity.
Integrated circuits will sometimes come out of their sockets during
shipment. Examine all integrated circuits, particularly the BIOS,
processor, memory modules, ROM-Disk, and keyboard controller chip
to ensure that they are firmly seated. The HS-7165 delivery package
contains the following items:
HS-7165 Board x 1
Utility CD Disk x 1, including User’s Manual
Cables (as following table)
Jumper Bag x 1

6
Cables Package
NO. Description QTY.
1 SATA cable 50cm (w/Lock) 1
2 COM DB9*2-10P(2.54) 30cm w/bracket 1
3 Print DB25-26P(2.54) 30cm w/bracket 1
4 SPK 8P(2.54) phone jack*2 27cm w/bracket 1
5 SATA power cable 15cm 1
6 USB 1-to-2 cable w/bracket 20cm 1
7 6P(JST2.0)-Mini DIN*2 cable 20cm w/bracket 1
It is recommended that you keep all the parts of the delivery package
intact and store them in a safe/dry place for any unforeseen event
requiring the return shipment of the product. In case you discover any
missing and/or damaged items from the list of items, please contact
your dealer immediately.
Option Accessories
NO. Description
1 USB 1-to-2 cable w/bracket 20cm
2 SATA cable 50cm (w/Lock)
3 SATA power cable 15cm
4 COM DB9*2-10P(2.54) 30cm w/bracket
5 H=23mm CPU Cooler

7
Chapter 3
Hardware Installation
This chapter provides the information on how to install the hardware
using the HS-7165. This chapter also contains information related to
jumper settings of switch, and watchdog timer selection etc.
3.1 Before Installation
After confirming your package contents, you are now ready to install
your hardware. The following are important reminders and steps to
take before you begin with your installation process.
1. Make sure that all jumper settings match their default settings
and CMOS setup correctly. Refer to the sections on this chapter
for the default settings of each jumper. (JP4 short 1-2)
2. Go through the connections of all external devices and make
sure that they are installed properly and configured correctly
within the CMOS setup. Refer to the sections on this chapter
for the detailed information on the connectors.
3. Keep the driver CD in good condition for future reference and
use.

8
3.2 Board Layout

9
3.3 Jumper List
Jumper Default Setting Setting Page
JP2 Panel Voltage Select: +3.3V Short 2-3 10
JP4 Clear CMOS: Normal Operation Short 1-2 16
JP10 Short 1-2
JP11 Short 1-2
JP12
FSB Frequency Select: Auto Detect
Short 2-3
10
JP13 Short 1-2
JP14 Short 1-2
JP15 Short 1-2
JP16
CF or SATA 3 Connector Select: SATA
Short 1-2
13/17
JP18 Short 1-2
JP19
Onboard Display or External PCIe x16
Select: Onboard Display Open 10/17
CN13 COM 4 Use RS-232 or RS-422/485 Select:
RS-232 Open 13
3.4 Connector List
Connector Definition Page
CN3/CN4 LVDS Panel Connector 10
CN6/CN5 DDRII Socket 10
CN7/CN8/CN9/CN32 SATA 0~SATA 3 Connector 13
CN10 8-bit GPIO 23
CN12 Parallel Port 16
CN14 RS-422/485 Connector (3x2 header) 13
CN16 System Front Panel Connector 18
CN17 CompactFlash Connector 21
CN18 Internal 6-pin KB/MS Connector 17
CN19/CN20 RJ-45 Connector 15
CN23 DVI-I Connector 10
CN24 MIC In/Audio Out Connector 20
CN25/CN26/CN33 Internal USB2.0 Ports 15
CN27 15-pin CRT Connector 10
CN31/CN30/CN29/CN28 COM 1~COM 4 Connector 13
CN34 External USB2.0 Port 15
FN1/FN2 CPU Fan Power Connector 17
JP1 Inverter Power Connector 10
PW1 4-pin ATX Power Connector 17

10
3.5 Configuring the CPU
The HS-7165 embedded with Intel® Mobile Dual Core processor,
supports Merom 65nm and Penryn 45nm (Socket P).
zJP10/JP11/JP12: FSB Frequency Select
Settings
Options JP10 JP11 JP12
CPU Driven (default) Short 1-2 Short 1-2 Short 2-3
1066MHz FSB Open Short 2-3 Short 2-3
800MHz FSB Open Open Short 2-3
667MHz FSB Short 2-3 Open Short 2-3
13
13 13
3.6 System Memory
The HS-7165 provides two 240-pin DIMM sockets at locations
CN6/CN5. It supports DDR2 up to 4GB SDRAM.
3.7 VGA Controller
The HS-7165 provides four types of connection for display device.
CN27 is a 15-pin CRT connector. CN3/CN4 are the LVDS interface
connectors onboard reserved for flat panel installation. HS-7165 also
provides DVI-I connector at location CN23.
zJP18/JP19: Onboard Display or External PCIe x16 Bus Select
CRT Version
Settings
Options JP18 JP19
CRT Function (default) Short 1-2 x
External PCIe x16 Short 2-3 x
13

11
DVI-I Version
Settings
Options JP18 JP19
DVI-I Function (default) Short 1-2 Open
External PCIe x16 Short 2-3 Short
13
zCN27: 15-pin CRT Connector
PIN Description PIN Description
1 Red 2 Green
3 Blue 4 N/C
5 GND 6 GND
7 GND 8 GND
9 VCC 10 GND
11 N/C 12 DDCDA
13 HSYNC 14 VSYNC
15 DDCCL
1
7123914
5
611281341015
zCN3/CN4: LVDS Interface Connector
PIN Description PIN Description
1 VLCD 2 VLCD
3 GND 4 GND
5 A0-/B0- 6 A0+/B0+
7 A1-/B1- 8 A1+/B1+
9 A2-/B2- 10 A2+/B2+
11 CLK1-/CLK2- 12 CLK1+/CLK2+
13 A3-/B3- 14 A3+/B3+
1
2
13
14
NOTE: LVDS cable should be produced very carefully. A0- & A0+ have to
be fabricated in twister pair (A1- & A1+, A2- & A2+ and so on)
otherwise the signal won’t be stable. Please set the proper voltage
of your panel using JP1 before proceeding on installing it.

12
zJP1: Inverter Power In Connector
PIN Description
1 +12V
2 +12V
3 VCC
4 BK_EN
5 LCD_EN
6 GND
NOTE: If use CN3 only, it just supports 24-bit single channel LVDS panel;
If you want to use 48-bit dual channel LVDS panel, please use CN3
and CN4 combined.
The HS-7165 has an onboard jumper that selects the working voltage
of the flat panel connected to the system. Jumper JP2 offers two
voltage settings for the user.
zJP2: Panel Voltage Select
Options Settings
+3.3V (default) Short 2-3
+5V Short 1-2
13
zCN23: DVI-I Connector
PIN Description PIN Description
1 - DATA2 2 DATA2
3 GND 4 -DATA4
5 DATA4 6 DDCCLK
7 DDCDATA 8 VSYNC
9 -DATA1 10 DATA1
11 GND 12 -DATA3
13 DATA3 14 VCC5
15 GND 16 HPDET
17 -DATA0 18 DATA0
19 GND 20 -DATA5
21 DATA5 22 GND
23 CLK 24 -CLK
25 RED 26 GREEN
27 BLUE 28 HSYNC
29 GND 30 GND

13
3.8 Serial ATA Connector
You can connect the Serial ATA device that provides you high speeds
transfer rates (300MB/sec.).
zCN7/CN8/CN9/CN32: Serial ATA Connector
PIN Description
1 GND
2 SATATXP
3 SATATXN
4 GND
5 SATARXN
6 SATARXP
7 GND
17
zJP13/JP14/JP15/JP16: CF or SATA 3 Connector Select
Settings
Options JP13 JP14 JP15 JP16
SATA 3 (default) Short 1-2
CF Short 2-3
1
3
1
3
1
3
1
3
3.9 Serial Port Connectors
The HS-7165 offers 16C550 compatible UARTs with Send/
Receive 16-byte FIFO serial ports.
zCN31/CN30/CN29/CN28: COM 1 ~ COM 4 Connector (5x2
Header)
PIN Description PIN Description
1 DCD 2 DSR
3 RXD 4 RTS
5 TXD 6 CTS
7 DTR 8 RI
9 GND 10 Don’t Use
19
102

14
zCN14: RS-422/485 Connector (3x2 Header, COM 4)
PIN Description PIN Description
1 TX- 2 TX+
3 RX+ 4 RX-
5 GND 6 N/C 15
62
NOTE: The terminal resistance of RX & TX is set at 180 Ω .
zCN13: COM 4 use RS-232 or RS-422/485 Select
Options Settings
RS-232 (default) Open
RS-485 Transmit Only (*1) Short 1-2, 3-4, 5-7, 8-10
RS-485 by –RTS (*-1) Short 1-2, 3-4, 7-9, 8-10
RS-422/485 Full Duplex (*2) Short 1-2, 3-4, 6-8
19
102
NOTE: *1: 2-wires RS-485 function
*2: 4-wires point-to-point full duplex function
4-wires point-to-point full duplex RS-422/485
Typical RS-485 2-wires Mutildrop Network