Lanner electronics IAC-F694 Series User manual

IAC-F694 Series
Dual Pentium III Full-size SBC
with VGA, Two 100Base-T Ethernet
for Socket 370 Processors

COPYRIGHT©
This document is copyrighted by the original manufacture. The original manufacturer
reserves the right to make modifications to the product(s) described in this manual at any
time without notice. This manual may not, in whole or in part, be photocopied,
reproduced, transcribed, translated, or transmitted in whatever form without the written
consent of the manufacturer, except for copies retained by the purchaser for backup
purposes. All rights are reserved.
TRADEMARKS
Pentiumis a registered trademark of Intel Corporation.
The following are trademarks or registered trademarks of their respective companies:
IBM, Intel, AMD, Cyrix, Award, AMI, S3, Microsoft, Windows, Windows NT, Novell, SCO,
PC/104, PICMG, ALI, UMC, SMC, Winbond. Products mentioned in this manual are for
identification purposes only. All names of products or services appearing in this manual
are the trademarks or registered trademarks of their respective organizations and
companies.
Copyright 2002
Ver. No. 1.0
LEI-UM-IAC-F694 Series
Date: 9.24.2002

TABLE OF CONTENTS
CHAPTER 1 INTRODUCTION 1
1.1 SPECIFICATIONS 2
1.2 PACKING CHECK LIST 3
CHAPTER 2 JUMPER SETTING AND CONNECTORS 4
2.1 BOARD OUTLINE OF IAC-F694 SERIES 4
2.2 INSTALLING AND UPGRADING THE CPU 5
2.3 JUMPER SETTING OVERVIEW 6
2.4 JUMPER LOCATIONS FOR IAC-F694 SERIES 7
2.6 JUMPER SETTINGS SUMMARY FOR IAC-F694 8
2.7 JUMPER SETTINGS FOR IAC-F694 SERIES 9
2.7 I/O CONNECTOR LOCATIONS FOR IAC-F694 SERIES 12
2.8 I/O CONNECTOR SUMMARY FOR IAC-F694 13
2.9 I/O CONNECTORS DESCRIPTION 14
CHAPTER 3 AWARD BIOS SETUP 21
3.1 RUNNING AWARD BIOS 21
3.2 CMOS SETUP UTILITY 22
3.3 STANDARD CMOS SETUP 24
3.4 BIOS FEATURES SETUP 26
3.5 CHIPSET FEATURES SETUP 29
3.6 INTEGRATED PERIPHERALS 32
3.7 POWER MANAGEMENT SETUP 35
3.8 PNP/PCI CONFIGURATION 40
3.9 PC HEALTH STATUS 42
3.10 FREQUENCY / VOLTAGE CONTROL 43
3.11 LOAD FAIL-SAFE DEFAULTS 44
3.12 LOAD OPTIMIZED DEFAULTS 44
3.13 SET SUPERVISOR / USER PASSWORD 45
3.14 SAVE & EXIT SETUP 45
3.15 EXIT WITHOUT SAVING 45

TABLE OF CONTENTS
CHAPTER 4 DRIVERS SUPPORT 46
4.1 DRIVER DISKETTE LIST 46
APPENDIX A HOW TO USE WATCH-DOG TIMER 47
APPENDIX B TECHNICAL REFERENCE 48
GLOSSARY 50
TERMS AND CONDITIONS
RMA SERVICE REQUEST FORM

~ 1 ~
CHAPTER 1.
INTRODUCTION
The IAC-F694 Series is a Duel Pentium III PICMG Single Board Computer specifically
designed for Socket 370 with VGA, two 10/100Base-TX Ethernet. This makes the
IAC-F694 Series a perfect solution for not only popular Networking Devices like Firewall,
Gateway, Router, and e-Server, but also CTI (Computer Telephony Integration) equipments
such as PBX, Digital Logger, etc.
With VIA 694X/686B chipsets, IAC-F694 Series supports Ultra DMA-33/66/100 for faster
hard drive transmission speeds and contains health monitoring hardware. The health
monitoring IC keeps an eye on the CPU and releases an audio alarm when detecting
abnormal operating voltage & temperature or malfunction of the cooling fans. For
boosting operation, this motivated card also supports sockets for a Flash Disk and three
DIMMs support up to 1.5GB SDRAM.
Other on-board features include two serial ports (RS-232 and RS-232/422/485), one
multi-mode parallel (ECP/EPP/SPP) port, a floppy drive controller, a keyboard interface
and a PS/2 mouse interface. The built-in high speed PCI IDE controller supports both PIO
and bus master modes. Supporting up to two floppy disks, this board also can connect up
to two IDE devices. Its 8-layer printed circuit board combined with noise-tolerant and low
power consumption CMOS technology allow the IAC-F694 Series to withstand many harsh
industrial environments.
IAC-F694 Series is a high power & full engine Single Board Computer CPU card , carefully
designed to be a feature-rich SBC CPU card at a reasonable price, this board elegantly
meets industry needs and saves time and money by waiving the hassle of going through
the extra effort and cost of additional I/O cards. Being standards-compliant, it is proved to
be a quality product with high performance and stability in a long run.

INTRODUCTION
~ 2 ~
1.1 SPECIFICATIONS
❏Processor : Dual IntelPentium III/ One CeleronProcessor in
Socket 370, support FSB 66/100/133 MHz CPU
❏Chipset : VIA 694X/686B chipset
❏System Memory/RAM : Three 168-pin DIMM sockets, support up to 1.5 GB
SDRAM
❏BIOS : Awardlicensed BIOS ( 2M bit Flash ROM )
❏Flash Memory Disk : Reserved socket for DiskOnChip from M-System,
support up to 144 MB flash memory disk
❏AGP VGA Controller : ATI Rage XL
❏Ethernet Controller : Two Intel 82559 chip, support two 10/100M Base-T,
on-board RJ-45 connector, and wake on LAN function.
❏IDE Drive Interface : Two PCI IDE port that support up to four IDE devices
and Ultra DMA-33/66/100
❏Floppy Drive Interface : One FDD port, support up to two floppy devices
❏Serial Port : Two COM ports, one RS-232 and one RS-232/422/485
❏Parallel Port : One multi-mode parallel port ( SPP / EPP / ECP )
❏Bus Interface : PICMG bus
❏RTC Battery : Internal RTC with Li battery
❏Keyboard/Mouse Connector: One 6-pin mini-Din PS/2 keyboard/mouse connector and
5-pin keyboard header
❏Watchdog Timer : Hardware/Software Watchdog Timer, support 16-level
time-out intervals
❏Digital I/O : 4-bit digital I/O header
❏Universal Serial Bus : Support two USB connectors
❏IR Interface : Support IrDA header
❏Health Monitoring : System integrated Health Monitor function
❏Operating Temperature : 0 °C ~ 60 °C
❏Storage Temperature : -20 °C ~ 70 °C
❏Humidity : 5 %~95%RH, noncondensing
❏Dimensions : 338.5 x 122 mm ±0.5 mm
❏Net Weight : 300g (0.66 pounds)
❏EMI/EMS : EN 50081-1/1994>EN 55022/1997>EN 00-3-2/1995
>EN 61000-3-3/1995, EN 50082-1/1994>IEC
1000-4-2/1995, IEC 1000-4-3/1995, IEC 1000-4-4/1995
❏Ording Information :
IAC-F694A : Dual-CPU/VGA/LAN*2
IAC-F694B : Single-CPU/VGA/LAN*2
CPU Fan : High-quality CPU Fan

INTRODUCTION
~ 3 ~
1.2 PACKING CHECK LIST
Inspect the product package for the following items before installation. If there is anything
missing, please contact our authorized reseller.
Item Qty Remark
IAC-F694 1 pc IAC-F694 Dual Pentium III Full-Size SBC
IDE Cable 1 pc DMA-66 IDE cable
FDD cable 1 set 34-pin to 34-pin standard header flat ribbon cable
LPT cable 1 pcs 26-pin standard header to 25-pin female D-Sub
Keyboard and Mouse cable 1 pcs 6-pinmale Mini-Din to 5-pin Din/ 6-pin Mini-Din
ATX Feature Cable 1 pc 4-pin to 4-pin
COM3/COM4 Cable 1 pc Two COM Cable. with Bracket
Drivers Utility 1 pc CD-ROM
User‘s manual 1 pc IAC-F694 user’s manual

~ 4 ~
JUMPER SETTING AND CONNECTORS
The figure below shows the jumpers and connectors location on the IAC-F694 Series.
2.1 Board Outline of IAC-F694 Series
CHAPTER 2.
VGA1
PKM1
LAN1
CPU
KCN1
LPT1FDC1IDE1 / IDE2DIMM3 DIMM2
DIMM1
1
JP2 3
FAN2
13
10
PLRS1
1
1
SWD1
2 1
ISP1
8
DIO1
1
2
10 9
A
TXC1
1
4
SDOC1
1 2
109
SC2T1
1
2 5
6
1
TWD1
9
4
12
USBC1
1 2
109
2
10
COM1/COM2
2
10
SC2T2
1 9
4 12
3
1
JP3
CMOS1
1 3
CPU
FAN1
13
LAN2
IRDA1
1

JUMPER SETTING AND CONNECTORS
~ 5 ~
2.2INSTALLING AND UPGRADING THE CPU
To upgrade to a higher power CPU, simply remove the old CPU and install a new one. Make
sure to set the jumpers for the new CPU type and speed.
WARNING!
Disconnect the power cord from your system when you intend to
work on it or when you plan to open the chassis of your industrial
computer. Do not make connections when the power is turned on
because the sensitive electronic components could be damaged
by the sudden rush of power. Please only allow experienced
electronic technicians to do this job.
STATIC ELECTRICITY PRECAUTION!
Caution! Computer components are very sensitive to damage
from static electric discharge. Always ground yourself to remove
static charge build-up before touching the boards in the computer.
Use a grounding wrist strap at all times. Place all electroni
c
components on anti-static pad for static-dissipation or in
static-shielded bag when they are not in the chassis.
CAUTION!
Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the batter
y
manufacturer’s instructions or accepted environmental regulator
y
standards.

JUMPER SETTING AND CONNECTORS
~ 6 ~
2.3 JUMPER SETTING OVERVIEW
In order to select the operation modes of your system, configure and set the jumpers on your
single board computer to match the need of your application. To set a jumper, a black plastic
cap containing metal contacts is placed over the jumper pins as designated by the required
configuration as listed in this section. A jumper is said to be “ on ” or “ 1-2 ” when the black
cap has been placed on two of its pins, as show in the figure below:
A pair of needle-nose pliers is recommended when working with jumpers. If you have any
doubts about the best hardware configuration for your application, contact your local sales
representative before you make any changes. In general, you simply need a standard cable
to make most connections.