Advantech PCE-5127 Installation and operation manual

PCE-5127/7127 Startup Manual 1
Before you begin installing your card, please make sure that
the following items have been shipped:
1. 1 PCE-5127/7127 PICMG 1.3 Single Host Board
2. 1 PCE-5127/7127 startup manual
3. 1 CD with utility
4. 1 user note for full-sized CPU card
5. 2 Serial ATA HDD data cables
6. 2 Serial ATA HDD power cables
7. 1 COM + printer ports cable kit
8. 1 4-port USB cable kit
9. Keyboard and mouse Y cable
10. 1 jumper package
11. 1 warranty card
If any of these items are missing or damaged, please con-
tact your distributor or sales representative immediately.
Note 1: For detailed contents of PCE-5127/7127, please
refer to information on the enclosed CD-ROM (in
PDF format).
Note 2: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at: get.
adobe.com/reader (Acrobat is a trademark of
Adobe)
Note 3: PCE-7127G2-CN don’t support printer port,
Hardware monitor and IPMI. 1701260305 (Print
port+COM cable) is excluded in package
PCE-5127/7127 LGA1155 Intel®CoreTM i7/i5/i3/ Pen-
tium®/Xeon®PICMG 1.3 Single Host Board with
(ECC) DDR3 / Dual GbE LAN
Startup Manual
General
• LGA1155 Intel®Core™ i7/i5/i3/Pentium®/Xeon®
• BIOS: AMI 64 Mb SPI BIOS
• Chipset:
- PCE-7127: Intel C216
- PCE-5127: Intel Q77
• System memory:
- PCE-7127G2: Supports dual channel DDR3 1333/1600
8GB per DIMM with ECC; Max. capacity is up to 16GB
- PCE-5127G2: Supports dual channel DDR3
1333/1600 8GB per DIMM without ECC; Max. capacity
is up to 16GB
• SATA ports:
- PCE-7127G2: Supports 2 SATA3.0 and 4 SATA2.0 with
Raid 0, 1, 5, 10.
- PCE-5127G2: Supports 2 SATA3.0 and 4 SATA2.0 with
Raid 0, 1, 5, 10.
Note 1: SATA3.0: 600MB/sec; SATA2.0:300MB/sec
Note 2: PCE-5127/7127 does NOT support any IDE ports.
• Serial ports: Two RS-232 with pin Headers
• Parallel port: One parallel port, supports SPP/EPP/ECP
mode. PCE-7127 CN version don’t support printer port
• Keyboard/mouse connector: Supports one standard
PS/2 keyboard and mouse connector and one external
6-pin header
• Watchdog timer: 255 level timer intervals
• USB 2.0:
- PCE-7127G2: 9*USB2.0 (Pin-header*4+USB Type A*1+
4 on backplane)
- PCE-5127G2: 9*USB2.0 (Pin-header*4+USB Type A*1+
4 on backplane)
• USB 3.0:
- PCE-7127G2: 3*USB3.0 (Pin-Header*2+Rear*1)
- PCE-5127G2: 3*USB3.0 (Pin-Header*2+Rear*1)
• GPIO: One programmable 8-bit GPIO pin-header
VGA Interface
• Chipset: Intel®HD Graphics
• Shared system memory is subject to OS
Ethernet Interface
• Chipset supports:
- LAN 1: Intel
®
82579LM for all SKUs
- LAN 2: Intel
®
82583V for PCE-5127G2 and
PCE-7127G2-CN
Intel
®
82574L for PCE-7127G2
• Connection: 2 on-board RJ-45 connector with LED
indicators
Specications
Packing List
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://support.advantech.com.tw/support/default.
aspx
This manual is for the PCE-5127/7127 Series Rev. A1.
Part No. 2006512701
Printed in China
2nd Edition,
Sep. 2014

2 PCE-5127/7127 Startup Manual
Specications
Mechanical and Enviromental
• Dimensions: (L x W): 338 x 122 mm
• Power supply voltage: +3.3 V, +5 V, +12 V
• Power requirements:
CPU: Processor: Intel
®
Core™ i7-3770;
Memory: 2 DDR3 1333 MHz 4 GB DIMMs
Voltage: +12 V, +5 V, +3.3 V, +5 VSB, -12 V, -5 V
Current: 5.37A, 0.98A, 1.44A, 0.42A, 0.01A, 0A
Operating temperature: 0 ~ 60° C (depending on CPU)
• Weight: 0.5 kg (weight of board)
The board has a number of jumpers that allow you to con-
figure your system to suit your application. The table below
lists the function of each of the jumpers and connectors.
Connectors
Label Function
LPT1
Parallel port, Parallel port x 1, supports
SPP/EPP/ECP mode. (PCE-7127 CN
version don’t support LPT)
LAN1 Intel
®
82579LM for all SKUs
LAN2
Intel(R)82583V for PCE-5127G2 and
PCE-7127G2-CN
Intel(R)82574L for PCE-7127G2
VGA1 VGA connector
KBMS1 PS/2 keyboard and mouse connector
KBMS2 External keyboard/mouse connector
COM1 Serial port: COM1; RS-232 (9-pin Box
Header)
COM2 Serial port: COM2; RS-232 (9-pin Box
Header)
JIR1 Infrared connector
JFP3
(Keyboard
Lock and
Power LED)
Power LED
Suspend: Fast ash (ATX/AT)
System On: ON (ATX/AT)
System Off: OFF (AT)
System Off: Slow flash (ATX)
JFP2 External speaker / SATA HDD LED
connector
JFP1 Power Switch / Reset connector
JCASE1 Case Open
CPUFAN1 CPU FAN connector (4-pin)
LANLED1 LAN1/2 LED extension connector
HDAUD1 HD audio extension module connector
USB12 USB port 1, 2
USB8 USB port 2
USB56 USB port 4, 5
USB7 USB port 6
USB910 USB port 8, 9
S ATA 1 Serial ATA1
S ATA 2 Serial ATA2
S ATA 3 Serial ATA3
S ATA 4 Serial ATA4
S ATA 5 Serial ATA5
S ATA 6 Serial ATA6
CPU1 CPU Socket
DIMMA1 Memory connector channel A
DIMMB1 Memory connector channel B
GPIO1 GPIO pin header (SMD pitch-2.0 mm)
LPC1 COM port module expansion pin-header
Jumpers
Label Function
JCMOS1 CMOS clear
JMECLR1 Clear ME data
JWDT1 Watchdog timer output selection
JOBS1 HW Monitor Alarm
JCMOS1/JMECLR1: Clear CMOS/ME data
Closed Pins Result
1-2 Keep CMOS/ME data*
2-3 Clear CMOS/ME data
Jumpers and Connectors
Jumpers and Connectors
Closed Open

PCE-5127/7127 Startup Manual 3
The drivers for the PCE-5127/7127 are located on the
software installation CD. Please click through the folder and
follow the screen instructions to install them.
Caution! The computer is supplied with a battery-powered
realtime clock circuit. There is a danger of explo-
sion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended
by the manufacturer. Discard used batteries ac-
cording to manufacturer’s instructions.
This device complies with the requirements in Part 15 of
the FCC rules. Operation is subject to the following two
conditons:
1. This device may not cause harmful interference;
2. This device must accept any interference received,
including interference that may cause undesired opera-
tion.
H/W monitor alarm (JOBS1)
Function Jumper Setting
Closed Enable OBS alarm*
Open Disable OBS alarm
JWDT1: Watchdog timer output option
Closed Pins Result
1-2 Reserved
2-3 System reset*
* Default Setting
Jumpers and Connectors
Declaration of Conformity
Figure 1: Board Layout: Jumper and Connector Locations
Board Layout
Software Installation
COM2
COM1
LAN1
LAN2
USB8
VGA1
KBMS1
KBMS2
LPC1
JIR1+ JOBS1+JWDT1 JCASE1
GPIO1
HD
AUDIO1
CPU1
CPU FAN1 DIMMB1
DIMMA1
SATA
1~6
USB910
USB56 USB7
USB12
LPT1
LANLED1
JFP1~3
DVI1
JCMOS1 JMECLR1
SPI_CN1
JERP1