bouncepad Sumo User manual

Sumo
Assembly
Instructions

Contents
In the Box
Tools Required
Configuration Options
Configuration A
Configuration B
A1
B1
A20
B19

1
In the Box
1Sumo Case
2Sumo Stalk
4Case Clamping Plate
3Surface Clamping Plate
5Case Keys x2
8T30 Security Driver Bit
10 M6 x 40mm
1 5/8” Socket Set-screw x5
9Nyloc Nuts x5M6
7M6 Split Washers x5
6M6 x 12mm
15/32” Button-head Security Screw x4

7
10
6
9
Need advice if you’re
using custom fixings?
Give us a call.
8
2
4
3
5
Key Number

A D E F G
Tools Required
APencil
CDrill
BTape Measure
GSocket Screwdriver
D6mm
1/4” Drill Bit
E16mm
5/8” Drill Bit
F10mm Spanner
CB

Configuration Options

Fixing From Below
A
If fixing your Sumo from below
your mounting surface follow: A
The mounting surface must not
be thicker than 25mm or 1” for
this option.
Configuration

Fixing From Above
B
If fixing your Sumo from above
your mounting surface follow: B
Configuration
Screws must be no shorter than
30mm or 1 1/4” for this option.
*(screws not supplied)

Ensure that you follow the
correct section for your chosen
mounting configuration.

The mounting surface must not
be thicker than 25mm or 1” for
this option.
Fixing From Below
A Configuration

A1
B
A
A2
If your Sumo Stalk Base Rotation is configured to off, follow
steps + . Mark out the positions for the Mounting Holes.
Please note that your chosen rotate configuration will determine
the minimum distance you can mount Sumo from a wall.
A2A1
0º
Rotate
Plan
View
Minimum Distance: 30mm

Rear Edge of Mounting Surface or Wall
E D
D
D
D
D
Align Base
using Cable Slot
0º
Rotate
30mm - Minimum Distance
Screen Direction
Cable Slot
A2

If your Sumo Stalk Base is configured for a 70°Rotation
follow + . Mark out the positions for the Mounting Holes.
Please note that your chosen rotate configuration will determine
the minimum distance you can mount Sumo from a wall.
A3 A4A3
B
A
A4
Minimum Distance: 30mm
70º
Rotate
Plan
View

Rear Edge of Mounting Surface or Wall
E
D
D
D
D
D
Align Base
using Cable Slot
70º
Rotate
30mm - Minimum Distance
Cable Slot
Screen Direction
Screen Direction
Screen Centre Position
A4

If your Sumo Stalk Base is configured for a 180°Rotation
follow + . Mark out the positions for the Mounting Holes.
Please note that your chosen rotate configuration will determine
the minimum distance you can mount Sumo from a wall.
A5 A6A5
B
A
A6
Minimum Distance: 135mm
180º
Rotate
Plan
View

Screen Centre Position
Screen Direction
Screen Direction
Rear Edge of Mounting Surface or Wall
Cable Slot
E
D
D
D
D
D
Align Base
using Cable Slot
180º
Rotate
135mm - Minimum Distance
A6

If your Sumo Stalk Base is configured for a 270°Rotation
follow + . Mark out the positions for the Mounting Holes.
Please note that your chosen rotate configuration will determine
the minimum distance you can mount Sumo from a wall.
A7 A8A7
B
A
A8
Minimum Distance: 180mm
270º
Rotate
Plan
View

Rear Edge of Mounting Surface or Wall
E
D
D
D
D
D
Align Base
using Cable Slot
270º
Rotate
180mm - Minimum Distance
Cable Slot
Screen Direction
Screen Direction
Screen Centre Position
A8

Drill the mounting holes in your surface using the
appropriate Below Surface Mounting Template for your
rotate configuration - these guidelines can be found on the
previous pages of this booklet.
A9
C
E
D

A10 Attach the socket set-screws into the base of the Sumo
Stalk. These screws must be tightened by hand to the full depth
of the internal thread - do not over tighten.
2
10