Bounty Hunter Land Star User manual

OWNER’S MANUAL
The Land Star is a professional metal detector. The concepts and
terminology can be quite unfamiliar if you are new to the hobby.
To understand it quickly and to get the most enjoyment possible
from your detector, we strongly recommend that you:
1) Turn the Sensitivity knob to a low setting if you get false
signals. A little practice is required to understand when and how
you can use the sensitivity at or near 100%.
2) Do not use indoors. This detector is for outdoor use only. Many
household appliances emit electromagnetic energy, which can
interfere with the detector. If conducting an indoor
demonstration, turn the sensitivity down and keep the search
coil away from all floors, walls and metal objects.
3) Read this manual.
Most importantly, review the Summary of Operating Modes (10)
and the Quick-Start Demo (6).
4) Use 9volt ALKALINE batteries only.

2
TABLE OF CONTENTS
TERMINOLOGY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
BATTERIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
QUICK-START DEMO . . . . . . . . . . . . . . . . . . . . . . . . . . .6
BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . .7, 8, 9
GROUND BALANCING . . . . . . . . . . . . . . . . . . . . . . . . . .9
SUMMARY OF OPERATING MODES . . . . . . . . . . . . . .10
LCD TARGET DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . .11
DEPTH & BATTERY INDICATORS . . . . . . . . . . . . . . . .12
SENSITIVITY ADJUSTMENT . . . . . . . . . . . . . . . . . . . .12
AUDIO TARGET IDENTIFICATION . . . . . . . . . . . . . . .13
IN THE FIELD TECHNIQUES
Motion Modes . . . . . . . . . . . . . . . . . . . . . . . . .14 & 15
No-Motion Modes . . . . . . . . . . . . . . . . . . . . . .16 & 17
Pinpointing with All-Metal Mode . . . . . . . . . . . . . . . .16
TROUBLE SHOOTING GUIDE . . . . . . . . . . . . . . . . . . .18
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

TERMINOLOGY
ELIMINATION
Reference to a metal being "eliminated" means that the detector will not emit a tone,
nor light up an LCD indicator, when a specified object passes through the coil’s
detection field.
DISCRIMINATION
When the detector emits different tones for different types of metals, and when the
detector "eliminates" certain metals, we refer to this as the detector "discriminating"
among different types of metals. Discrimination is a fixed-start-point elimination system.
NOTCH
Notching is the elimination of an item, or range of items, within the metallic spectrum.
We "notch-out" an object selectively. Objects to the left and right on the metallic
spectrum are retained. Notching creates a variable rejection window.
RELIC
A relic is an object of interest by reason of its age or its association with the past.
Many relics are made of iron, but can also be made of bronze or precious metals.
IRON
Iron is a common, low-grade metal that is often an undesirable target in certain metal
detecting applications. Examples of undesirable iron objects are old cans, pipes,
bolts, and nails.
Sometimes, the desired target is made of iron. Property markers, for
instance, can contain iron. Valuable relics can also be composed of iron; cannon
balls, old armaments, and parts of old structures and vehicles can also be
composed of iron.
FERROUS
Metals which are made of, or contain, iron.
PINPOINTING
Pinpointing is the process of finding the exact location of a buried object. Long-buried
metals can appear exactly like the surrounding earth, and can therefore be very hard
to isolate.
PULL-TABS
Discarded pull-tabs from beverage containers are the most bothersome trash items
for treasure hunters. They come in many different shapes and sizes. We have
incorporated special features into the detector to let you automatically eliminate the
most common types, using the AutoNotch Mode. Since there are many different
types, some must be "Notched-Out" manually.
GROUND BALANCE
Ground Balancing is the ability of the detector to ignore, or "see through," the earth’s
naturally occurring minerals, and only sound a tone when a metal object is detected.
WATERPROOF
The search coil can be submerged in water. The control housing and cable-to-housing
connection must, however, stay dry.
COINSHOOTING
Finding buried coins is the most popular metal detecting application. The most valuable
are very old; take care in unearthing them to avoid damage.
CACHE HUNTING
Pronounced “cash”. A cache is a buried or hidden valuable stored inside a case, strong
box, or bag.
3

4
EASY ASSEMBLY
Search Coil
Search
Coil
Cable
Upper
Stem
Control
Housing
Plug
Lower
Stem
Assembling your Land Star Metal De-
tector is easy and requires no tools. Just
follow these steps:
●
1Using the supplied bolt and knurled
knob, attach the search coil to the
lower stem.
●
2Twist stem locking nut counter
clockwise. Press the button on the
upper end of the lower stem and slide
the lower stem into the upper stem.
Adjust the stem to a length that
lets you maintain a comfortable
upright posture, with your arm
relaxed at your side. Tighten the
stem locking nut.
●
3Wind the search coil cable around
the stem. Leave enough slack in the
cable to let you adjust the coil when
you are hunting on uneven ground.
Then tighten the knob at the end of
the search coil.
Note: To adjust the coil,
simply loosen the knob.
●
4Insert the coil’s plug into the
matching connector on the control
housing. Be sure the holes and
pins line up correctly.
Caution:
• Do not force the plug in.
Excess force will cause damage.
• To disconnect the cable, pull on the
plug. Do not pull on the cable.
Lower
Stem
Stem
locking
nut
Upper
Stem
Connector
on back of
control housing
Bolt Knurled
Knob
Bottom view
Bottom side

5
BATTERIES
IMPORTANT: Always use ALKALINE batteries for optimal performance.
Always remove the batteries for prolonged storage.
CHECK THE BATTERIES if your detector exhibits any of the following
symptoms:
●
1The unit does not turn on.
●
2Low speaker volume.
●
3Unable to tune detector with the discriminate knob.
The Low Battery indicator light will come on and stay on whenever the
batteries need replacing. It should flash momentarily when the Power
Switch is turned on.
IMPORTANT: Your Land Star metal detector requires two 9-Volt
ALKALINE batteries.
Follow these steps to install the batteries.
●
1Carefully remove the battery compartment door by pressing the release
clip on the right side of the door.
●
2Snap one battery onto each of the terminals and place the batteries in-
side the compartment.
●
3 Replace the compartment door by carefully inserting opposite side of clip first.
Then press down on clip side until battery door snaps into place.
Release
Clip Alkaline Batteries

QUICK-START DEMO
I. SUPPLIES NEEDED
• Nickel • Quarter
• Dime • A Nail or other iron object
• A Zinc Penny
(dated after 1982)
II. POSITION THE DETECTOR
a. Place the detector on a table, with the search
coil hanging over the edge.
(or better, have a friend hold the
detector, with the coil off
the ground)
b. Keep the search coil away from
walls, floors, and metal objects.
c. Remove watches, rings and other jewelry
or metal objects from hands and wrists.
d. Turn off appliances or lights that cause electromagnetic interference.
e. Pivot search coil to a position parallel to the ground.
III. POWER UP
a. Turn the detector on and turn
the sensitivity knob to the
3:00 position.
b. Move the Disc/Notch Knob
100% counterclockwise.
IV. WAVE OBJECTS OVER SEARCH COIL
a. Wave coins with flat surface parallel to coil. This is how you’ll find them
buried in the ground.
b. Notice the different tones.
c. Watch the LCD indicator for depth and target identification.
V. DISCRIMINATE
a. Wave the nail and slowly turn the Disc/Notch Knob clockwise until the
nail is eliminated.
b. Continue eliminating objects one-by-one, by turning the Disc/Notch Knob
clockwise as you wave each object. Stop turning after the zinc penny is
eliminated.
c. The objects will be eliminated in this order:
1) Nail 2) Nickel 3) Penny
VI. NOTCH
a. Press the Notch button.
b. Position the Disc/Notch Knob so that the penny is eliminated.
c. Notice that the nickel is now detected. The penny has been "notched-out."
VII. ENTER ALL METAL MODE
a. Press ALL METAL touch pad.
b. Move an object into the coil’s field. In A/M mode, the object will emit a
monotone sound whenever a metal object is within the search coil’s field.
c. If volume (hum) increases, press GROUND TRAC button to stabilize.
6

7
TURN THE DETECTOR ON
Click the left knob to the on position.
The detector automatically enters the DISCRIMINATION Mode.
MOTION ALL-METAL Mode
To operate in this mode:
• Turn the right knob, Disc/Notch, 100% counterclockwise, to the off
position.
• Press the DISC button.
• Reduce the Sensitivity Control to the 2:00 or 3:00 position.
• Sweep the coil over the surface of the ground.
The detector will emit one of three tones, depending on the type of metal
detected.
The top display will indicate the type of metal targeted.
The bottom display will indicate the depth, in inches, of coin-sized objects.
A worthwhile target is evidenced by a consistent tone, and a repeatable
target and depth indication as you sweep back and forth over the same spot
on the ground. Non-repeatable tones indicate the presence of trash objects
or highly oxidized metals.
You can increase the level of sensitivity, depending on the ground
conditions. If the detector emits false signals, simply reduce the Sensitivity
until the false signals cease. The detector will work well with the Sensitivity
in the 2:00 or 3:00 position, but higher Sensitivity settings will increase depth
detection.
DISCRIMINATION Mode
To operate in this mode:
• Press the DISC button.
• Reduce the Sensitivity Control
to the 2:00 or 3:00 position.
• Sweep the coil over the
surface of the ground.
• Turn the right knob,
Disc/Notch, to eliminate
unwanted items from
detection as illustrated to the
right:
BASIC OPERATION

8
BASIC OPERATION
continued
NOTCH Mode
To operate in this mode:
• Press the NOTCH button.
• Use the Disc/Notch Knob to eliminate medium tone trash items from
detection, but still retain low and high tone valuables.
AUTONOTCH Mode
To operate in this mode:
• Press the AUTONOTCH button.
• Most pull-tabs and medium tone trash items are automatically
eliminated.
• The Disc/Notch Knob operates as in the NOTCH mode.
NO-MOTION ALL-METAL MODE
To operate in this mode:
• Hold the search coil over the ground surface, about 1/2 inch.
• Press the All-Metal Button.
The detector will emit only one monotone sound, regardless of the type
of metal detected.
If the detector emits a constant tone, press GROUND-TRAC with the
search coil just above the ground surface. Make sure that the ground area
chosen for tuning the detector does not contain metal; if unsure, switch into
DISC mode, turn off DISCRIMINATION and verify that the detector does not
emit tones as you sweep the coil over the chosen spot.
Ground conditions can change over short distances. Until you become
familiar with the detector’s volume level, retune the detector periodically by
pressing the GroundTrac button.
Temperature changes also require retuning, by pressing the Ground Trac
button. If the detector emits a constant tone, or loses sensitivity, retune. If
you have stored the detector indoors and move outdoors immediately to a
different temperature environment and begin detecting, retune the detector
periodically until the coil temperature stabilizes. This retuning is only
necessary in the ALL-METAL Mode.
To change into any mode at any time, simply press the desired button.
The GroundTrac button only functions when in the All-Metal Mode.

9
BASIC OPERATION
continued
MANUAL GROUND BALANCING
Your Land Star Metal Detector has a pre-set ground balance and a
manual adjustment knob.
When searching in the ALL METAL mode, it is important that the detector
be ground balanced to offset the effects of any minerals present in the
soil or to balance the effects of salt water when you search near the
ocean. This is how you can adjust the ground balance.
1. Turn GB knob 100% clockwise.
2. Hold searchcoil several inches above the ground.
3. If you’re not in ALL METAL mode, momentarily press the ALL METAL
button. If you’re already in ALL METAL mode, momentarily press the
GROUND TRAC button.
4. Lower the searchcoil to within about an inch of the ground. In most
soils, the sound volume will increase.
5. Turn the GB knob slowly counterclockwise until the sound is almost,
but not quite, gone.
6. You are now ground balanced and ready to search.
NOTE: If you want to ground balance a little more accurately, do the
following additional steps:
7. Raise the searchcoil again, several inches above the ground.
8. Momentarily press the GROUND TRAC button.
9. Lower the searchcoil to within about an inch of the ground. If the sound
goes up, carefully turn the ground balance knob slightly
counterclockwise until the sound almost goes away. If the machine is
quite, carefully turn the ground balance knob slightly clockwise until you
just barely hear sound.

10
SUMMARY OF OPERATING MODES
I. NO-MOTION ALL-METAL MODE
• Deepest Seeking Mode
• No motion is required
• All metals will be detected
• One tone only
• Manual Ground Balance: User must first ground balance the detector using the Ground Balance Knob.
To Operate: 1) Press All-Metal button.
2) Balance with GroundBalance button.
3) Press GroundTrac button, and re-tune as necessary.
Applications: Pinpointing Objects located in motion modes
Relic Hunting
Cache Hunting
Household applications: finding lost items, locating property markers
II. MOTION ALL-METAL MODE
• Motion Required
• All metals will be detected
• Three-tone Audio Target Identification
To Operate: 1) Press DISC button.
2) Keep Disc/Notch Knob 100% counterclockwise.
3) Reduce Sensitivity Knob in event of false signaling.
Applications: Relic Hunting
Cache Hunting
Household applications: finding lost items, locating property markers
III. DISCRIMINATION MODE
• Motion Required
• Three-tone audio target identification
• Disc/Notch Knob allows user to eliminate unwanted items.
• Discrimination is a cumulatively target elimination system.
• As you turn the knob farther clockwise, more objects are eliminated, including the first items
eliminated.
• Reduce Sensitivity if the detector emits false or non-repeatable signals.
• Automatic Ground Balance: detector automatically adjusts to ground mineralization as you
sweep the coil.
To Operate: 1) Press DISC button
2) Move Disc/Notch Knob to desired setting.
3) Reduce Sensitivity Knob in event of false signaling.
Applications: Coin-Shooting
Jewelry Hunting
IV. NOTCH MODE
• Automatically eliminates all ferrous objects.
• Disc/Notch Knob allows user to eliminate medium-tone trash items, but retain low and
high-tone valuables.
To Operate: 1) Press NOTCH button.
Other Operations and Applications: same as Discrimination Mode.
V. AUTONOTCH MODE
• Automatically eliminates all ferrous objects.
• Automatically eliminates most pull-tabs.
• Disc/Notch Knob allows user to eliminate medium-tone trash items, but retain low and
high-tone valuables.
To Operate: 1) Press AUTONOTCH button
Other Operations and Applications: same as Discrimination Mode.

11
LCD TARGET DISPLAY
-Motion modes only
READING THE DISPLAY
The LCD Target Display is accurate in
the Motion Modes only.
The Liquid Crystal Display (LCD) shows
the PROBABLE identification of the
targeted metal, as well as the PROBABLE
depth of the target, in inches.
Pass the search coil repeatedly over a
target, and observe the target readout.
The detector will register a repeated,
unchanging target identification when a
buried target has been located and
identified. If, upon repeated passes over
the same spot, the target identification
reads inconsistently, the target is probably
a trash item, or oxidized metal. With
practice, you will learn to unearth only the
repeatable signals.
The segment identifications are highly
accurate, when detecting the objects
described on the label. For example, if
you pass the coil repeatedly over a nickel,
your detector will repeatedly register a
nickel. However, if you repeatedly register
a nickel, for an unknown buried object,
you could be detecting some other
metallic object with the same magnetic
signature as a nickel.
GOLD TARGETS Gold objects will
register on the left side of the LCD scale.
Gold flakes will register under Iron/Foil
Small gold items will register under Pull
Tab.
Medium-sized gold items will register
under S-caps.
Large gold items will register as Zinc 1¢.
SILVER TARGETS: Silver objects will
register to the right of the scale, under
25¢, 50¢, or $1, depending on the size
of the object. The larger the object, the
farther to the right it will register.
IRON/FOIL: All but very large iron and
aluminum objects will register on the
far-left side of the scale. This could
indicate a worthless item such as a nail,
or a more valuable historic iron relic.
PULL TAB: All older pull tabs from
beverage cans will register here. Most
newer pull tabs will register here. Many
gold rings will also register here.
5¢: Nickels and newer pull tabs register
here.
S-CAPS: Older screw caps from glass
bottles will register here. Large gold
rings, like a class ring, could also register
here. Some non-U.S. coins of recent
vintage will also register here.
1¢ ZINC: Newer pennies (post-1982)
will register here. Many non-U.S. coins
of recent vintage will also register here.
10¢: Dimes and pre-1982 pennies will
register here. Older, pre-1982, pennies
are composed of copper, which has a
metallic signature similar to a dime.
Caution: The target indications are visual
references. Many other types of metal can
fall under any one of these categories. You
will experience a trash-to-treasure ratio
when treasure hunting. The more you
practice, the lower you will push your trash-
to-treasure ratio. While the Land Star will
eliminate or indicate the presence of most
common trash items, it is impossible to
accurately classify ALL buried objects. The
LCD provides a visual reference to minimize
the detection of trash objects. By using the
target ID in conjunction with discrimination
control and the three-tone audio
identification system (discussed later), you
can further reduce the trash-to-treasure ratio.

12
BATTERY INDICATOR:
The LOW BATT indicator will flash as
the unit is powered on. If the
indicator comes on and stays on,
replace the batteries.
DEPTH INDICATOR:
The Depth Indicator is accurate for
coin-sized objects. It indicates the
depth of the target, in inches. Large
and irregularly-shaped objects will
yield less reliable depth readings
When passing over an object, the
depth indicator will light up and stay
illuminated until another object is
scanned. Pass repeatedly over the
suspected target and pause briefly at
the end of each sweep to read your
display. Repeated indication at the
same depth level indicates an accurate
target detector. If the depth indication
varies with each sweep, try sweeping
at different angles; there may be more
than one target present. With practice,
you will learn the difference between
accurate readings, multiple targets,
and highly erratic readings which
evidence trash or irregularly shaped
objects.
SENSITIVITY ADJUSTMENT:
The principle use for the SENSITIVITY
knob is to eliminate
ELECTROMAGNETIC INTERFERENCE
(EMI). EMI is both naturally-occurring
and man-made. Common sources of
EMI are power lines, both suspended
and buried, and broadcasting
antennas. Machinery, when in
operation, can also produce EMI.
EMI comes from most household
appliances, so YOUR DETECTOR
CAN BEHAVE VERY ERRATICALLY
INDOORS. If you want to test it
indoors, turn off the TV and
microwave. If you have lights with
dimmer switches, also turn these off;
dimmer switches can produce lots of
EMI.
If your detector falses with the
SENSITIVITY knob in the 100%
clockwise position, reduce the
sensitivity until the chatter stops
(usually to the 1:00 or 3:00 position).
If you suspect the presence of deeper
targets underneath a shallower target,
reduce the SENSITIVITY to eliminate
the detection of the deeper target to
properly locate and identify the
shallower target.
BATTERY/ DEPTH INDICATORS & SENSITIVITY ADJUSTMENT
Depth indicator locked on 8 inches

13
AUDIO TARGET ID
-Motion modes only
In the DISC, NOTCH or AUTONOTCH
modes, the detector emits three
distinct tones, which classify metal
objects into categories
IRON & STEEL:
In the DISCRIMINATION mode most
iron and steel objects will induce a low
tone. Highly oxidized iron can induce a
high tone, depending on the
Disc/Notch control setting. For
instance, some rusted bottle caps will
induce a high tone and indicate to the
right of the LCD target display. A very
large iron object, like a manhole cover,
can induce a high tone.
GOLD:
Gold objects will induce a low or
medium tone, depending on their
sizes. Very small gold objects will
indicate on the left-most segment.
Large gold objects will read under the
Zinc segment. If you are gold
prospecting, you will usually be
looking for natural gold in an area
which it does not contain much trash,
and can therefore ignore the specific
segment descriptions.
PULL TABS:
Pull tabs are the most bothersome
trash items for detectorist. Most will
induce a medium tone. Most will be
eliminated automatically in the AUTO
NOTCH mode, or alternatively be
manually “notched out” in NOTCH
mode with the Disc/Notch control. The
older pull tabs (those not attached to
the can after opening) are sometimes
broken in half; these broken tabs can
induce low tones. Highly oxidized pull
tabs can also induce high tones.
It can be very difficult to differentiate
pull tabs from gold rings. When they
both induce medium tones, you might
notice a “double beep” from a gold
ring but a “single beep” from pull tabs.
To achieve this distinction, sweep the
search coil very slowly, and at different
angles. Two tones might signal as the
detector passes over each side of the
round ring.
COPPER, SILVER & BRASS:
Most valuable coins are composed of
these metals and will usually induce a
high tone. Valuable objects other than
coinage can also be composed of
copper, silver and brass.
Audio Target Identification (ATI) classifies metals into three categories.
LOW TONE
Nails & Bottle Caps,
Gold & Nickel
MEDIUM TONE
Old & New Pull Tabs, Zinc,
Pennies (Post 1982), Larger
Gold Objects
HIGH TONE
Copper, Silver & Brass
Copper Pennies (Pre 1982)

14
IN THE FIELD TECHNIQUES
- Motion modes
PINPOINTING
Accurate pinpointing takes practice
and is best accomplished by
“X-ing” the target area.
1. Once a buried target is indicated
by a good tone response,
continue sweeping the coil over
the target in a narrowing
side-to-side pattern.
2. Take visual note of the place on
the ground where the “beep”
sounds.
3. Stop the coil directly over this
spot on the ground.
4. Now move the coil straight
forward and straight back
towards you a couple of times.
5. Again make visual note of the
spot on the ground at which
the “beep” sounds.
6. If needed, “X” the target at
different angles to “zero in” on
the exact spot on the ground at
which the “beep” sounds.
7. Use All-Metal mode (p16) for
more accurate pinpointing.
COIL MOVEMENT
When swinging the coil, be
careful to keep it level with the
ground about one inch from the
surface. Never swing the coil like
a pendulum.
CORRECT
WRONG
The
coil
should
be swung
in a
half-
circle
movement
as
illustrated
here.
Repeat this
motion
every step
you take to
guarantee that
the area is being
covered thoroughly.

15
IN THE FIELD TECHNIQUES
- Motion modes
After selecting your operating mode,
swing the search coil gently side-to-
side, slightly overlapping each sweep
as you move forward. Make sure you
keep your search coil approximately 1
inch above the ground as you search.
Raising it in the sweep, or at the ends
of your sweep, will cause false read-
ings. Move slowly; hurrying will only
cause you to miss targets.
Most good objects will respond
with a good repeatable signal.
If a signal does not
repeat after swinging
the coil directly
over
the suspected target a
few times, it is more
than likely trash
metal. False signals
can be caused by
trashy ground,
electrical
interference,
or by large
irregular
trash
objects. These signals are easily
recognized by their often broken or
non-repeatable nature.
The Land Star is a very sensitive
and deep-seeking detector. It will
respond loudly to many targets that
other detectors would only detect
with a weak signal. Because of
this, trash-induced signals and
other sources of interference may
cause signals that seem confusing.
The key to managing these false
signals is to dig only those targets
that emit a strong repeatable signal.
As you sweep the search coil
back and forth over the ground,
learn to recognize the difference
between the signals that occur at
random and signals that are
stable and repeatable.
When searching very trashy
ground, it is best to scan small
areas with slow, short overlapping
sweeps. To prevent erratic signals
and difficult pinpointing in trashy
areas, use the Bounty Hunter
4-Inch Gold Nugget Coil.
WHAT
READS
LIKE THIS
…MAY
ACTUALLY
BE THIS

16
IN THE FIELD TECHNIQUES
- No-motion modes
In the No-Motion All-Metal Mode, coil sweep technique is not important. Rather,
user retuning is critical.
The detector does not automatically adjust to changing ground and
environmental conditions; the operator is required to make the adjustment. If
the detector sounds a constant tone over all areas of the ground, retune the
detector by pressing the GroundTrac button.
RETUNING
Keep the coil still, just above the ground surface, and press the GroundTrac button.
Make sure that the spot on the ground you chose for tuning did not contain
metal; pass over the area with the coil again to insure that the detector does
not emit a tone.
TEMPERATURE CHANGE
If the detector moves from one temperature environment to another, or if the
temperature changes, you must retune the detector until the temperature
stabilizes. If you move from a cooler to a warmer environment, the detector may
emit a constant tone; if so, retune. If you move from a warmer to cooler
environment, the detector may lose sensitivity; if so, retune.
PINPOINTING
How To Pinpoint Targets Using The ALL-METAL Mode
When you’ve discovered a target you wish to dig, do the following:
1. Hold the searchcoil about half an inch above the ground, off to the side of
where you think the target probably is.
2. Tap the ALL METAL touchpad button. This will put you into the All Metal
Pinpoint mode. NOTE: unlike the other modes, this mode does not require
the searchcoil to be in motion to detect a target.
3. Lift the searchcoil slightly, and pass it over the target. The sound will be
loudest over the center of the target.
To Narrow It Down Further:
4. Now that you know about where the target is, again lower the searchcoil to
about half an inch above the ground, near the center of the target but not
right over the top. Tap the button again. The sound will instantly go away.
5. Lift the searchcoil slightly and move it horizontally over the target. The audi-
ble response zone will be much narrower. If you move the searchcoil
around right and left and also forward and back, making an “X” pattern over
the target, you can determine the location of the target usually within an inch
or two.
NOTE: if at any time it seems like the signal may be drifting, just tap the
Ground-Trac button. This restores the signal to its zero level.

17
IN THE FIELD TECHNIQUES
- No-motion modes
Detection Field
The No-Motion Mode’s detection field depends on the size of the target.
Large Objects
After detecting a target, lift the coil off the ground to a distance where you
hear the faintest tone. Move the coil over the ground at this height. If the
tone does not fade, you have detected a large or irregularly shaped object.
Outline the object with slow coil movements.
If you can outline an area larger than the size of the inside coil, you then have
a large target, or several targets.
Large objects can be detected when they enter the range of the outside coil.

ADDITIONAL ACCESSORIES AVAILABLE
MAXIMIZE YOUR METAL DETECTING EXPERIENCE WITH THESE
BOUNTY HUNTER ACCESSORIES
4 INCH COIL
Great for searching in
trashy areas with its
smaller target area. Also
perfect for gold prospecting
and fitting into tight spaces.
10 INCH COIL
For maximum depth
detection.
HEADPHONES
Increase battery life and
find more deeply buried
objects, evidenced by faint
signals sometimes
undetected with the
standard speaker.
CARRY BAG
Custom-sized to carry your
detector.
COIL COVERS
Protect your coil from wear
& tear. 4 inch, 8 inch, 10
inch.
www.detecting.com
18

19
SYMPTOM CAUSE SOLUTION
Detector chatters
or beeps erratically
Constant low tone
or constant repeating
tones
LCD does not lock
on to one target ID
or emits multiple
tones
No power, no
sounds
• Use detector
outdoors only
• Move away
from
power lines
• Keep 2 detectors
at least 20’
apart
• Only dig up
repeatable signals
• Reduce sensitivity
until erratic
signals cease
• Replace batteries
• Use only 9V
alkaline batteries
• Move coil slowly
at different
angles
• Reduce sensitivity
• Replace batteries
• Check connections
• Using detector
indoors
• Using detector near
power lines
• Using 2 detectors in
close proximity
• Highly oxidized
buried object
• Environmental
electromagnetic
interference
• Discharged batteries
• Wrong type of
batteries
• Multiple targets
present
• Highly oxidized
target
• Sensitivity set
too high
• Dead batteries
• Batteries connected
improperly
• Cord not connected
securely
TROUBLE SHOOTING

TREASURE HUNTER’S CODE OF ETHICS:
1. Respect the rights, property, and privacy of others.
2. Do not enter private property without permission.
3. Do not damage property, buildings, or vegetation.
4. Make yourself aware of federal, state, and local laws which
may govern the use of metal detectors in certain areas.
5. Do not damage historical or archeological treasures.
6. If you find something the rightful owner of which can be
identified, make the effort to return it.
7. ALWAYS refill any holes you may have dug.
First Texas Products, LP
1100 Pendale Road
El Paso, TX 79907
[phone] REVISED 10/03
Copyright© 2003 by First Texas Products, L.P.
All rights reserved, including the right to reproduce this book, or parts thereof, in any form, except for the
inclusion of brief quotations in a review.
Published by First Texas Products, L.P.
Bounty Hunter®is a registered trademark of First Texas Products, L.P.
www.detecting.com
Bounty Hunter Metal Detectors are warranted
against defects in workmanship or materials under
normal use for five years from date of purchase to
the original user. Liability in all events is limited to
the purchase price paid. Liability under this
Warranty is limited to replacing or repairing, at our
option, any Bounty Hunter Detector returned,
shipping cost prepaid, to First Texas Products, LP.
Damage due to neglect, accidental damage or
misuse of this product is not covered by this
warranty.
FIRST TEXAS PRODUCTS, LP
5-YEAR LIMITED WARRANTY