Brähler Systems DIGIMIC DExt User manual

Quick Guide
DIGIMIC DExt
Extension power supply unit
Extension power supply unitExtension power supply unit
Extension power supply unit
Article no.: 05.0025

DIGIMIC DExt Quick Guide
Quick GuideQuick Guide
Quick Guide
2
BRÄH ER Systems GmbH
Auf der Alten Burg 6
53639 Königswinter
T
+4
9 (0)
224
4
930
-
0
F [phone] [e-mail]
www.braehler-systems.com
05.0025 190220 V1.0 BRÄH ER Systems verbessert ständig seine Produkte und behält sich daher technische Änderungen ohne Ankündigung vor
Introduction
IntroductionIntroduction
Introduction
With the DExt from the DIGIMIC family it is
possible to extend the DIGIMIC system.
The number of units controlled by the DCen32 is
limited by the power consumption of the devices.
The DExt, which supplies longer device chains
with additional power, provides a remedy. Almost
infinitely long chains are possible. In addition, the
distance between the control centre and the first
unit can be significantly extended - up to 100m per
DExt.
Depending on the type, the number of
units per chain varies: DIGIMIC CS up to
40 units, CMic and CMic ID up to 25,
DDol up to 14 (examples).
The DExt is connected to other devices of the DIGIMIC family via CAT5e cables or better.
It is not allowed to be mixed different device types of the DIGIMIC family in one chain.
Connection from the previous
desk or from the control panel
Connection to
the next desk
mains connection
ED power display
Example system
drawing

DIGIMIC DExt Quick Guide
Quick GuideQuick Guide
Quick Guide
3
BRÄH ER Systems GmbH
Auf der Alten Burg 6
53639 Königswinter
T
+4
9 (0)
224
4
930
-
0
F [phone] [e-mail]
www.braehler-systems.com
05.0025 190220 V1.0 BRÄH ER Systems verbessert ständig seine Produkte und behält sich daher technische Änderungen ohne Ankündigung vor
Connection
Connection Connection
Connection
To put the DExt into operation, connect the DExt to the last unit of the preceding chain or to the central unit
using the RJ45 plug...
… and with the first unit of the next chain.
Connect the DExt to the mains plug and connect it to the power supply. Only use suitable cables for this
purpose. The DExt has an automatic on/off switch - this means the unit will not start until it receives power
from an upstream console or central unit. The yellow ED (Power) indicates correct operation (if the mains
plug is plugged in and an upstream unit is sending power).
The DExt is ready for use immediately and does not
need to be configured separately.
To switch off the DExt, disconnect the mains plug
from the power supply or switch off the upstream
device.
The DExt connectors are only suitable for other devices of the DIGIMIC family. Do not connect
any other devices.
In case of malfunctions, contact a technician, do not attempt to repair, unscrew or similar the
DExt by yourself.
Connection from
previous
unit
or from the central unit
Connection to
next unit

DIGIMIC DExt Quick Guide
Quick GuideQuick Guide
Quick Guide
4
BRÄH ER Systems GmbH
Auf der Alten Burg 6
53639 Königswinter
T
+4
9 (0)
224
4
930
-
0
F [phone] [e-mail]
www.braehler-systems.com
05.0025 190220 V1.0 BRÄH ER Systems verbessert ständig seine Produkte und behält sich daher technische Änderungen ohne Ankündigung vor
Further information about our products can be found on the Internet under:
www.braehler.com
© 2019
Copyright by BRÄH ER Systems GmbH, Königswinter
All rights reserved, in particular (also in extracts) those of translation, reprinting, reproduction by copying or
similar procedures.
BRÄH ER Systems reserves the right to make technical changes without prior notice.
Brähler Systems GmbH
Auf der Alten Burg 6
53639 Königswinter, Germany
T [phone]
F [phone]
[email protected]om