Bradley Bradex 2902-2800 User manual

2902-2800, 2902-2873, 2902-2874
Adjustable Motor, Adjustable Sensor-Operated Warm Air Hand Dryer
Washroom Accessories
Document No. 8256
© 2012 Bradley
P.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 800.BRADLEY (800.272.3539) Fax: [phone]
bradleycorp.com
Orders composed of products indicated as Bradex®will be available to ship in three days
after receipt of order at the factory. There is no pricing penalty for this service from Bradley.
Page 1 of 2
This information is subject to change without notice. 4/5/2012
Standard Model 2902-280000 (cast iron white
porcelain) Bradex®
Standard Model 2902-287300 (steel-white epoxy)
Bradex®
Standard Model 2902-287400 (stainless steel-satin
finish) Bradex®
Product Materials
2902-2800 COVER: 3⁄16" (4.5 mm) thick one-piece cast iron; white porcelain
enamel coating.
2902-2873 COVER: 1⁄16" (1.5mm) thick one-piece steel; white epoxy finish.
2902-2874 COVER: 1⁄16" (1.5mm) thick one-piece stainless steel; satin finish.
Cover fixed to the base plate with two vandal-proof lock screws and lock with
special key wrench.
ADJUSTABLE MOTOR: universal-type with high-speed, universal brush, fully
adjustable (3,800–8,200 RPM) potentiometer, Class A; Aluminium centrifugal
double asymmetrical inlet fan wheel; aluminum scroll fan and safety thermal cut-off.
HEATING ELEMENT: waved wire NiCr heating element mounted on a mica frame
that incorporates a self-resetting thermal cut-off at 302ºF.
ADJUSTABLE SENSOR OPERATION: electronic infrared detection sensor with
fully adjustable (2"–8") potentiometer. Includes polycarbonate viewing windows.
Automatic shut-off after 60 seconds.
BASE PLATE: 1⁄8" (3 mm) thick aluminum, with four Ø5⁄16" (8 mm) holes for wall
mounting. Includes silent blocking to dampen mechanical vibrations.
Installation
Verify all rough-in dimensions prior to installation. Hand dryers require a
dedicated circuit and must be properly grounded. GFI Circuit protection is
recommended. One side of dryer should be mounted to a stud.
Operation
Place hands 3"–6" below nozzle to activate air flow. Dryer will
stop two seconds after hands are removed from air flow.
Recommended for very high traffic areas.
®
ADA Compliant
Consult local and national accessibility codes for proper
installation guidelines.
Conformity and compliance to local and national codes is
the responsibilty of the installer.
Guide Specification
Surface-mounted ADA-compliant hand dryer shall have a thick cast iron cover
with white porcelain enamel coating (2902-2800) or steel cover with white epoxy
coating (2902-2873) or stainless steel cover with satin finish (2902-2874). Hand
dryer shall include aluminium base plate, fully adjustable (2"– 8") infrared sensor
potentiometer and fully adjustable (3800 - 8200 RPM) universal-type motor
potentiometer with resilient mounts and sealed, lubricated ball bearings. Dryer
shall operate at 64−70 dB while delivering 43−70 CFM of air at 106ºF–111ºF
(41ºC−44ºC) and 4,920−9,840 LFM velocity during user-controlled drying cycle.
Dryer shall have a total power of 800–1,150 W (1.07–1.54 Hp) with a consumption
of 9.5–4.8 A.
Overall dimensions: 10½"H x 11½"W x 4"D (267mm x 292mm x
102mm).
Weight: 7.9 lb (3.58 kg)
Product Specifications
Voltage: 100–120 V, 208 V, 220−240 V Consumption: 9.5–4.8 A
Motor: 1⁄3HP (250 W) RPM: 3,800–8,200
Nominal power: 1,150 W (1.54 Hp) Heating element: 900 W (1.20 Hp)
Effective airflow: 36–58 CFM Nominal airflow: 43–70 CFM
Noise level at 79": 64–70 dB Airspeed: 4,920–9,840 LFM
Frequency: 50/60 Hz Insulation: Grounding required
Temperature (at 4"
distance / 70ºF): 106ºF–111ºF (41ºC–44ºC)
Certificates: UL 499 / CSA C22.2 /
VDE GS / VDE EMC
Drying time: 10–15 seconds Mounting: Surface. ADA-compliant
Protection level: IP23 Splash Protection

2902-2800, 2902-2873, 2902-2874
Adjustable Motor, Adjustable Sensor-Operated Warm Air Hand Dryer
Washroom Accessories
Document No. 8256
© 2012 Bradley
P.O. Box 309, Menomonee Falls, WI 53052-0309
Phone: 800.BRADLEY (800.272.3539) Fax: [phone]
bradleycorp.com
Orders composed of products indicated as Bradex®will be available to ship in three days
after receipt of order at the factory. There is no pricing penalty for this service from Bradley.
Page 2 of 2
This information is subject to change without notice. 4/5/2012
11-5/8"
(295mm)
7¾"
(197mm)
9¼"
(235mm)
4"
(102mm)
10-5/8"
(270mm)
Model 2902-280000
4"
(102mm)
11½"
(292mm)
9¼"
(235mm)
7¾"
(197mm)
10½"
(267mm)
Models 2902-287300
and 2902-287400 All dimensions ± 4%.
9¼"
(235mm)
7¾"
(197mm)
4½"
(114mm)
Mounting Template Front View
ؼ"
(7mm)
Ø1"
(25mm)
Surface-mounted electrical
knockout located in lower
left corner of cover
Surface-mounted electrical
knockout located in lower
left corner of cover
Dim. "A"
to finished
floor
Dim. "A" Key Surface: For Dim. "A" Top of Unit Bottom of Unit
Sensor top to finished
floor
48" (1219mm) 57¾" (1467mm) 47¹⁄₈" (1197mm)
45" (1143mm) 54¾" (1391mm) 44¹⁄₈" (1121mm)
42" (1067mm) 51¾" (1314mm) 41¹⁄₈" (1045mm)
40" (1016mm) 49¾" (1264mm) 39¹⁄₈" (994mm)
Rough wall opening:
Surface Mount: No rough opening, see overall dimensions
Dimensions