Braeburn 140404 User manual

®
140404 4 Zone
Expandable Panel
Installer Manual
140404-100-03
Warning Read all of the instructions before proceeding
Can cause electrical shock or equipment damage. Always turn off power to the heating/air
conditioning system prior to installing or adjusting the expandable zone panel. Wire the entire
panel before applying transformer power.
This panel is designed for professional installation, and is to be installed and configured as
described in this manual. Any other use is not recommended and will void the warranty.
Install disconnect and overload protection on circuits as required by code authorities having
jurisdiction for the installation.
Voltage Hazard
Caution
Expandable up to 32 Zones
Up to 4 Heat / 2 Cool
Conventional or Heat Pump
Store this manual for future reference.

Specifications
1
Storage temperature:
-40˚–167˚F (-40˚–75˚C)
Operating temperature:
-22˚–167˚F (-30˚–75˚C)
Voltage:
24 VAC, Nominal 60Hz
18-30 VAC Maximum
Operating humidity:
5–95% RH
Panel Power:
6 VA @ 24 VAC
Current Draw Max:
100 VA @ 24 VAC
Current Draw Per Zone:
50 VA Max
2.1”
8”
8”
10.2”
Protection:
Electronic self resetting current
limiting for panel power and
damper zones
Configuration:
Conventional and Heat Pump
equipment up to 4 Heating Stages
and 2 Cooling Stages
Maximum Zones:
4 Zones Main Panel + 14 Two
Zone Expanders = 32 Total
Zones Maximum
Dimensions:
See Figure 1
Figure 1
Table of Contents
1 Specifications .....................................................................................................................2
2
Suitable Mounting Locations ...............................................................................................3
3
Wiring .............................................................................................................................4-9
4 Configuration ....................................................................................................................10
5 System Check-Out ............................................................................................................13
6 Operation ...............................................................................................................................14
7 ErrorConditions .................................................................................................................17
8 Adding More Zones ...........................................................................................................19
9 Warranty ..........................................................................................................................22
2

Suitable Mounting Locations
2
Mount the Zone Panel near the HVAC equipment. The panel can be mounted in any orientation on a wall,
stud, roof truss, or the return-air plenum. For appearance, mount the panel level. Remove the panel cover
and use the base as a template to drill mounting holes (see Figure 2). Attach the panel with appropriate
screws. Use mounting anchors as needed for drywall or plaster installations.
Figure 2
3
EM HEAT
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 1
PO
COMM
PC
DAMPER
ZONE 1
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 2
DAMPER
ZONE 2
PO
COMM
PC
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 3
PO
COMM
PC
DAMPER
ZONE 3
24V
24C
POWER
24 VAC
EXPANSION
COM1
COM2
GND
COM3
COM4
EXPANSION
COM1
COM2
GND
COM3
COM4
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 4
PO
COMM
PC
DAMPER
ZONE 4
Rh
Rc
Y1
Y2
G
G2
W1/E/AX1
W2/AX2
W3/O/B
L
C
E
QUIPMENT
FA1
FA2
FIRE
ALARM SENSORS
SA1
SA2
ODT1
ODT2
SENSORS
drill holes
drill holes

Wiring the Panel
3
Always turn off power to the heating/air conditioning system prior to installing or adjusting the Zone Panel. Wire the
entire panel before applying transformer power. Use the following general wiring instructions for all systems. Specific
wiring will vary depending on the equipment and type of system (conventional or heat pump). NOTE: Up to 2 wires
can be inserted into each terminal. To release wires, press down on top of wiring terminal and gently pull out wire(s).
EM HEAT
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 1
PO
COMM
PC
DAMPER
ZONE 1
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 2
DAMPER
ZONE 2
PO
COMM
PC
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 3
PO
COMM
PC
DAMPER
ZONE 3
24V
24C
POWER
24 VAC
EXPANSION
COM1
COM2
GND
COM3
COM4
EXPANSION
COM1
COM2
GND
COM3
COM4
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 4
PO
COMM
PC
DAMPER
ZONE 4
Rh
Rc
Y1
Y2
G
G2
W1/E/AX1
W2/AX2
W3/O/B
L
C
E
QUIPMENT
FA1
FA2
FIRE
ALARM
SENSORS
SA1
SA2
ODT1
ODT2
SENSORS
4
8
2
1
6
8
2
8
2
8
2
7
3
4
5
6
11 910 Figure 3

EM HEAT
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 1
PO
COMM
PC
DAMPER
ZONE 1
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 2
DAMPER
ZONE 2
PO
COMM
PC
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 3
PO
COMM
PC
DAMPER
ZONE 3
24V
24C
POWER
24 VAC
EXPANSION
COM1
COM2
GND
COM3
COM4
EXPANSION
COM1
COM2
GND
COM3
COM4
R
Y1
Y2
W1/E/AX1
W2/AX2
O/B/W3
G
L
C
T
HERMOSTAT
Z
ONE 4
PO
COMM
PC
DAMPER
ZONE 4
Rh
Rc
Y1
Y2
G
G2
W1/E/AX1
W2/AX2
W3/O/B
L
C
E
QUIPMENT
FA1
FA2
FIRE
ALARM
SENSORS
SA1
SA2
ODT1
ODT2
SENSORS
Terminal Qty. Function Description
PANEL 24V 1 INPUT 24 VAC Transformer Power 100 VA Maximum
POWER 24C 1 INPUT 24 VAC Transformer Common
DAMPERS PO 4 OUTPUT 24 VAC Power Open Zone Damper Terminal
COMM 4 OUTPUT Zone Damper Common Terminal
PC 4 OUTPUT 24 VAC Power Close Zone Damper Terminal
SUPPLY SA1 1 INPUT Plenum Supply Air Sensor Terminal 1 (No Polarity)
AIR SA2 1 INPUT Plenum Supply Air Sensor Terminal 2 (No Polarity)
OUTDOOR ODT1 1 INPUT Outdoor Air Sensor Terminal 1 (No Polarity)
AIR ODT2 1 INPUT Outdoor Air Sensor Terminal 2 (No Polarity)
FIRE FA1 1 INPUT Normally Closed or Open Dry Pair (No Polarity)
ALARM FA2 1 INPUT Normally Closed or Open Dry Pair (No Polarity)
EXPANSION COM1 2 PANEL Expander Panel Communication
COM2 2 PANEL Expander Panel Communication
GND 2 PANEL Expander Panel Communication Ground
COM3 2 PANEL Expander Panel Communication
COM4 2 PANEL Expander Panel Communication
EQUIPMENT Rh 1 INPUT 24 VAC Equipment Transformer Power Connection
Rc 1 INPUT
24 VAC Cooling Equipment Transformer (Dual Transformer Systems Only)
Y1 1 OUTPUT 1st Stage Compressor
Y2 1 OUTPUT 2nd Stage Compressor
G 1 OUTPUT 1st Stage Fan Control
G2 1 OUTPUT 2nd Stage Fan Control
W1/E/AX1 1 OUTPUT
[W1] 1st Stage Conventional Heat [E] Emergency Heat [AX1] 1st Stage Auxiliary Heat
W2/AX2 1 OUTPUT [W2] 2nd Stage Conventional Heat [AX2] 2nd Stage Auxiliary Heat
W3/O/B 1 OUTPUT [W3] 3rd Stage Conventional Heat [O] Cool Active Reversing Valve
[B] Heat Active Reversing Valve
L 1 INPUT System Malfunction Indicator
C 1 INPUT 24 VAC Transformer Common
THERMOSTAT R 4 OUTPUT 24 VAC Thermostat Power
Y1 4 INPUT 1st Stage Compressor Call
Y2 4 INPUT 2nd Stage Compressor Call
W1/E/AX1 4 INPUT [W1] 1st Stage Conventional Heat Call [E] Emergency Heat Call
[AX1] 1st Stage Auxiliary Heat Call
W2/AX2 4 INPUT [W2] 2nd Stage Conventional Heat Call [AX2] 2nd Stage Auxiliary Heat Call
O/B/W3 4 INPUT [O] Cool Active Reversing Valve Call [B] Heat Active Reversing Valve Call
[W3] 3rd Stage Conventional Heat Call
G 4 INPUT Fan Call
L 4 OUTPUT System Malfunction Indicator
C 4 OUTPUT 24 VAC Transformer Common
RESET BUTTON Press once to restart panel
Hold for 5 seconds to reset panel and restore all factory defaults
Rc/Rh TERMINAL JUMPER (J1) Open jumper for dual transformer installations
WIRE STRIP GUIDE Wires should be stripped 3/8 inch minimum
EXPANDABLE ZONE PANEL WIRING TERMINALS
5
1
2
3
4
5
6
7
8
9
10
11

Damper Wiring
3.1
Always turn off power to the heating/air conditioning system prior to installing or adjusting the zone panel. Wire
the entire panel before applying transformer power.
Use the following general wiring instructions for all systems. Specific wiring will vary depending on the equipment
and type of system (conventional or heat pump).
Install the system dampers using the instructions provided by the manufacturer. Connect the dampers to the zone
panel as shown for either a 2-wire or 3-wire damper. The sum of all dampers powered by the zone panel should
not exceed 100 VA at 24 VAC. Use a slave relay if additional damper power is required.
ALWAYS PROVIDE DISCONNECT AND OVERLOAD PROTECTION AS REQUIRED
Max. damper VA per Zone 50 VA @ 24 VAC
M
M
PO
COM
PC
Zone Panel 2-Wire Damper
PO
C
PC
PO
COM
PC
Zone Panel 3-Wire Damper
Thermostat Wiring
3.2
Install the system thermostats using the instructions provided by the manufacturer. Connect the thermostats to
the zone panel as shown. Do not mix conventional and heat pump thermostats on the same system. You can mix
single stage and multi-stage thermostats as long as they are all conventional or heat pump.
ALWAYS PROVIDE DISCONNECT AND OVERLOAD PROTECTION AS REQUIRED
1 HEAT / 1 COOL
R 24 VAC Power
W1 Heat Call
Y1 Cooling Call
G Fan Call
C 24 VAC Transformer Common
2 HEAT / 2 COOL
R 24 VAC Power
W1 Heat Call Stage 1
W2 Heat Call Stage 2
Y1 Cooling Call Stage 1
Y2 Cooling Call Stage 2
G Fan Call
C24 VAC Transformer Common
CONVENTIONAL THERMOSTATS (for use on conventional or heat pump systems)
3 HEAT / 2 COOL
R 24 VAC Power
W1 Heat Call Stage 1
W2 Heat Call Stage 2
W3 Heat Call Stage 3
Y1 Cooling Call Stage 1
Y2 Cooling Call Stage 2
G Fan Call
C24 VAC Transformer Common
6

3 HEAT / 2 COOL
R 24 VAC Power
W1 Heat Call Stage 1
W2 Heat Call Stage 2
W3 Heat Call Stage 3
Y1 Cooling Call Stage 1
Y2 Cooling Call Stage 2
G Fan Call
C24 VAC Transformer Common
1 HEAT / 1 COOL - No Auxiliary Heat
R 24 VAC Power
O/B Changeover Valve [Note 2]
Y1 Compressor Call (1st Stage Heating/Cooling)
G Fan Call
C 24 VAC Transformer Common [Note 1]
2 HEAT / 2 COOL - No Auxiliary Heat
R 24 VAC Power
O/B Changeover Valve [Note 2]
L Optional System Fault Monitor
Y1 Compressor Call Stage 1 (1st Stage Heating/Cooling)
Y2 Compressor Call Stage 2 (2nd Stage Heating/Cooling)
G Fan Call
C24 VAC Transformer Common [Note 1]
HEAT PUMP THERMOSTATS (for use on heat pump systems only)
2 HEAT / 1 COOL - With Auxiliary Heat
R 24 VAC Power
O/B Changeover Valve [Note 2]
L Optional System Fault Monitor
W2 Auxiliary Heat Relay (2nd Stage Heating)
Y1 Compressor Call (1st Stage Heating/Cooling)
E Emergency Heat Call
GFan Call
C24 VAC Transformer Common [Note 1]
3 HEAT / 2 COOL - With Auxiliary Heat
R 24 VAC Power
O/B Changeover Valve [Note 2]
L Optional System Fault Monitor
AX1 Auxiliary Heat Relay (3rd Stage Heating)
Y1 Compressor Call (1st Stage Heating/Cooling)
Y2 Compressor Call (2nd Stage Heating/Cooling)
EEmergency Heat Call
GFan Call
C24 VAC Transformer Common [Note 1]
4 HEAT / 2 COOL - With Auxiliary Heat
R 24 VAC Power
O/B Changeover Valve [Note 2]
L Optional System Fault Monitor
AX1 Auxiliary Heat Relay (3rd Stage Heating)
AX2 Auxiliary Heat Relay (4th Stage Heating)
Y1 Compressor Call (1st Stage Heating/Cooling)
Y2 Compressor Call (2nd Stage Heating/Cooling)
EEmergency Heat Call
GFan Call
C24 VAC Transformer Common [Note 1]
NOTES
[1] Wiring to the C terminal is required only for thermostat power.
[2] O (Cool active) or B (Heat active) must match the zone panel
installer settings.
Thermostat Wiring
3.2
7

Supply Air Sensor Wiring
3.3
Install the supply air sensor in the supply air plenum at least 2-3 feet after
the heat exchanger and coil. Make sure there are no zone dampers before the
supply air sensor. Connect the supply air sensor to the zone panel as shown.
SA1
SA2
Transformer Wiring
3.4
Install the transformer using the instructions provided by the manufacturer. Size the
transformer to the damper requirements. The zone panel has built-in, self-resetting
fuses. The maximum damper power per panel is 100 VA at 24 VAC. Connect the
transformer to the zone panel as shown.
NOTE: Additional dampers or dampers with a higher current draw will require the
use of a separate slave relay.
ALWAYS PROVIDE DISCONNECT AND OVERLOAD PROTECTION AS REQUIRED
24V
24C
CC
HOT
Dedicated
Zoning Transformer
Zone
Panel
Conventional Equipment Wiring
3.5
NOTE: For a heat pump system, see Section 3.6.
Connect a conventional heating system to the zone panel as shown. For a single stage heating and cooling
system, the 2nd and 3rd stage connections are not used. For a system using a dual transformer, remove
jumper Rc to Rh (see Figure 3, page 4). Make sure the neutrals (common) are connected. ALWAYS PROVIDE
DISCONNECT AND OVERLOAD PROTECTION AS REQUIRED
8
1 HEAT / 1 COOL Equipment
Set Equipment Type to SSC
Rh 24 VAC Power (Heating Transformer)
[Note 3]
Rc Cooling Transformer [Note 3]
W1 Heat Call
Y1 Cooling Call
G Fan Call
C24 VAC Transformer Common
2 HEAT / 2 COOL Equipment
Set Equipment Type to MSC
Rh 24 VAC Power (Heating Transformer)
[Note 3]
Rc Cooling Transformer [Note 3]
W1 Heat Call Stage 1
W2 Heat Call Stage 2
Y1 Cooling Call Stage 1
Y2 Cooling Call Stage 2
G Fan Call
C24 VAC Transformer Common
3 HEAT / 2 COOL Equipment
Set Equipment Type to MSC
Rh 24 VAC Power (Heating Transformer)
[Note 3]
Rc Cooling Transformer [Note 3]
W1 Heat Call Stage 1
W2 Heat Call Stage 2
W3 Heat Call Stage 3
Y1 Cooling Call Stage 1
Y2 Cooling Call Stage 2
G Fan Call
C24 VAC Transformer Common
NOTES
[3] Remove J1 jumper for dual transformer systems. Transformer common must come from cooling transformer.

Heat Pump Equipment Wiring
3.6
NOTE: For Conventional Systems, see Section 3.5
Connect a single or multi-stage heat pump system to the zone panel as shown. A conventional thermostat
may be used with a heat pump system, however, emergency heat will be controlled by the panel emergency
heat switch or the optional remote emergency heat switch. For a single stage system, the auxiliary heat
control is not used. ALWAYS PROVIDE DISCONNECT AND OVERLOAD PROTECTION AS REQUIRED
1 HEAT / 1 COOL - No Auxiliary Heat
Set Equipment Type to SSH
Rh 24 VAC Power (Heating Transformer)
Rc Connected to Rh with Jumper
O/B Changeover Valve [Note 4]
Y1 Compressor Call (1st Stage Heating/Cooling)
G Fan Call
C24 VAC Transformer Common
2 HEAT / 2 COOL - No Auxiliary Heat
Set Equipment Type to MSH
Rh 24 VAC Power (Heating Transformer)
Rc Connected to Rh with Jumper
O/B Changeover Valve [Note 4]
L Optional System Fault Monitor
Y1 Compressor Call Stage 1 (1st Stage Heating/Cooling)
Y2 Compressor Call Stage 2 (2nd Stage Heating/Cooling)
G Fan Call
C24 VAC Transformer Common
2 HEAT / 1 COOL - With Auxiliary Heat
Set Equipment Type to MSH
Rh 24 VAC Power (Heating Transformer)
Rc Connected to Rh with Jumper
O/B Changeover Valve [Note 4]
L Optional System Fault Monitor
W2 Auxiliary Heat Relay (2nd Stage Heating) [Note 5]
Y1 Compressor Call Stage 1 (1st Stage Heating/Cooling)
E Emergency Heat Call
G Fan Call
C24 VAC Transformer Common
3 HEAT / 2 COOL - With Auxiliary Heat
Set Equipment Type to MSH
Rh 24 VAC Power (Heating Transformer)
Rc Connected to Rh with Jumper
O/B Changeover Valve [Note 4]
L Optional System Fault Monitor
AX1 Auxiliary Heat Relay (3rd Stage Heating)
Y1 Compressor Call (1st Stage Heating/Cooling)
Y2 Compressor Call (2nd Stage Heating/Cooling)
EEmergency Heat Call
GFan Call
C24 VAC Transformer Common
9
4 HEAT / 2 COOL - With Auxiliary Heat
Set Equipment Type to MSH
Rh 24 VAC Power (Heating Transformer)
Rc Connected to Rh with Jumper
O/B Changeover Valve [Note 4]
L Optional System Fault Monitor
AX1 Auxiliary Heat Relay (3rd Stage Heating)
AX2 Auxiliary Heat Relay (4th Stage Heating)
Y1 Compressor Call (1st Stage Heating/Cooling)
Y2 Compressor Call (2nd Stage Heating/Cooling)
EEmergency Heat Call
GFan Call
C24 VAC Transformer Common
NOTES
[4] O (cool active) or B (heat active) is selected in the installer
settings menu.
[5] Install a field supplied jumper between the W2/AX2 and
W1/E/AX1 terminals if there is no separate emergency heat
relay installed.

Configuration
4
Use the following instructions to configure the zone panel. The zone panel is factory set for a 1 Heat / 1 Cool
Conventional System with Conventional Thermostats (Heat Call on W, Cool Call on Y). If the zone panel is installed
on other systems, you will need to make configuration changes described in this section.
To start configuration:
1. Press SETUP and hold for 3 seconds.
10
2. The panel backlight will turn on and the display
will change.
3. Change setting if needed by pressing SELECT.
4. To save and advance to the next setting press
the NEXT button.
5. Repeat steps 3-4 as necessary.
6. Press HOLD FOR BACK for 3 seconds to go back a step.
7. Press HOLD FOR EXIT for 3 seconds to exit setup menu.

Configuration
4
The configuration settings must be properly set in order for this zone panel to operate correctly. The Installer
Settings will automatically adjust so that settings that do not apply to this installation will be skipped.
All settings are shown below with comments.
No. Installer Setting Display Factory Setting Comments
(Notes follow table) Indicator Default Options (More information follows this table)
1 System Type SYSTEM SSC SSC Select for 1H/1C conventional equipment [Note 9]
MSC Select for 2H/1C up to 3H/2C conventional equipment [Note 9]
SSH Select for 1H/1C Heat Pump equipment
MSH Select for 2H/1C up to 4H/2C Heat Pump Equipment
2 Thermostat Type TSTAT TP CON CON Select for all thermostats conventional type
HP Select for all thermostats heat pump type
3 1st Stage Fan Control FAN 1 GAS GAS Select for 1st Stage fan controlled by equipment
EL Select for 1st Stage fan controlled by panel
4 Auxiliary Fan Control AUX FAN EL GAS Select for auxiliary fan controlled by equipment
EL Select for auxiliary fan controlled by panel
5 Reversing Valve Control REV VAL O O Select for cool active reversing valve
B Select for heat active reversing valve [Note 7]
6 Auxiliary Stage COMP LOC OFF OFF Select for Compressor runs with Auxiliary Heat Call
Compressor Heat ON Select for Compressor is off with Auxiliary Heat Call
Lockout
7 Zone Fan Purge Time PURGE 90 300 Select for 300 second purge into calling zone at call end
240 Select for 240 second purge into calling zone at call end
180 Select for 180 second purge into calling zone at call end
120 Select for 120 second purge into calling zone at call end
90 Select for 90 second purge into calling zone at call end
60 Select for 60 second purge into calling zone at call end
30 Select for 30 second purge into calling zone at call end
0 Select for no purge into calling zone at call end
8 Supply Air Sensor Control SA SENS YES YES Select for Active Supply Air Sensor
NO Select for Inactive Supply Air Sensor [Note 5]
9 Plenum High Limit Cutout PLENUM 170
100 to 180 Select the maximum Supply Air Temperature the system
SET HI LIMIT can reach before shutting off all heating stages [Note 6]
10 Plenum Low Limit Cutout PLENUM 45
30 to 60 Select the minimum Supply Air Temperature the system
SET LO LIMIT can reach before shutting off all cooling stages [Note 6]
11
(continued)

No. Installer Setting Display Factory Setting Comments
(Notes follow table) Indicator Default Options (More information follows this table)
11 Short Cycle Protection SCP 55 to 0 Selects a compressor short cycle protection delay of 5,
4, 3, 2 or zero minutes after a compressor call
12
Outdoor Sensor Compressor COM BAL NO NO Disables Compressor Balance Point Control
Balance Point 0 to 50 Selects a Compressor Balance Point of 0 to 50° F
[Note 1, 2]
13 Outdoor Sensor Auxiliary AUX BAL NO NO, Disables Auxiliary Heat Balance Point Control
Heat Balance Point 40 to70 Selects an Auxiliary Heat Balance Point of 40 to 70° F
[Note 1, 2]
14 Equipment Staging STAGING ZON ZON Select to stage on number of zones calling (Setting 15)
TIM Select to stage on Zone Panel Timer
TST Select to stage on Thermostat Staging Calls [Note 8]
15 Equipment Staging Lock STAGLOK 2 2 - # of Selects the number of zones that must call before the
zones equipment will upstage Zone Count (setting 14 = ZON)
16
Second Stage Fan Control G2 FAN ZON ZON Select to Turn on Second Stage Fan on number of calling
zones (Setting 17)
STG Select to Turn on Second Stage Fan when second stage
is activated
17 Second Stage Fan G2 ZONES 2 2 - # of Select the number of zones that must call before the
zones second stage fan will turn on
18 Priority Zone PRIORTY 1 OFF Select to have opposite calls answered in any zone
1 to 4 Select zone 1 to 4 to limit calls so equipment will only
service call matching last call of zone 1-4
19 Opposite Mode Timer OP MODE 15 15 to 60 Select the number of minutes to delay system changeover
when zones are calling for heat and others zones are
calling for cooling.
20 Zone to Activate EM HEAT 1 NO Select to allow Emergency Heat from Thermostats
Emergency Heat 1 to 4 Select to match the Zone on the main panel allowed to
call emergency heat. [Note 3]
21 Fire Alarm FIRE ALM NI NI Select for a normally inactive (Open) fire relay
Normal Active / NA Select for a normally active (Closed) fire relay
Normal Inactive [Note 4]
12
NOTES - Configuration
[1] Only available if MSH system type is selected.
[2] Only available if outdoor sensor is connected.
[3] Thermostat type must be heat pump.
[4] All equipment and fans will shut down and all dampers will power close
[5] Disable will not show plenum temperature and will prevent staging by temperature.
[6] Only available if supply air sensor is enabled.
[7] O/B selection on equipment must match thermostat O/B selection.
[8] Multi-stage thermostats must be used.
[9] Set thermostats to conventional.

System Checkout
5
After the wiring and configuration is complete, built in automatic zone panel tests may be used to verify
equipment, damper, and panel operation.
To start the panel Test Mode:
1. Ensure all wiring is complete and power has been applied to the main and expansion panels
2. Press TEST for 3 seconds and release
3. Press SELECT to turn the test on and off
4. Press NEXT to move on to the next test
5. Press HOLD FOR EXIT for 3 seconds to exit test mode
The following tests are available in Test Mode:
Expansion Panel Zone Communication Test
(only if expander panels are connected)
This test will confirm or add expansion stages to the main zone
panel. Each recognized zone is shown from the lowest to the
highest number by pressing the select key. If a zone is
communicating properly, the display will show the zone number
and OK. If the zone is not communicating properly, the display
will show “Address Invalid” or “Duplicate Address”. See Error
Conditions, section 7 for help troubleshooting. Press SELECT
to Test or NEXT to advance to the next test.
Heating Stage(s) Test ON or OFF
This test turns on all heating stages (including O-B for heat pump
configurations) the system fan, and commands all dampers to
open. The heating stages will by energized by the type of system
configured in the installer settings. A heat pump configuration
will have all compressor calls and Auxiliary Heat. A conventional
configuration will call all conventional heating stages.
Press SELECT to Test or NEXT to advance to the next test.
Cooling Stage(s) Test ON or OFF
This test turns on all cooling stages (including O-B for heat pump
configurations), the system fan, and also commands all dampers
to open. Press SELECT to Test or NEXT to advance to the next test.
13

Fan Stage(s) Test ON or OFF
This test turns on all fan stages and commands all dampers
to open. Press SELECT to test or NEXT to advance to the next test.
Operation
6
The Expandable Zone Panel has LED’s and a built-in display
to tell the installer and the system owner the current operating
mode of the panel. Refer to the figure below and the following
descriptions of the panel LED’s for operation information.
Damper Control Test PO or PC
This test powers all dampers open or closed. Press SELECT to test
or NEXT to advance to return to first test.
LED COLOR INDICATION
Panel Status LED
Panel Power Green Flashing Green When Normal
Equipment LED’s
Rh Red 24 VAC at equipment Rh Terminal
Rc Red 24 VAC at equipment Rc Terminal
Y1 Yellow First Stage Compressor Call Active
Y2 Yellow Second Stage Compressor Call Active
G Green First Stage Fan Call Active
G2 Green Second Stage Fan Call Active
W1/E/AX1 White W1 or E or AX1 Call Active
W2/AX2 White W2 or AX2 Call Active
O/B/W3 Green Reversing Valve Active or W3
L Yellow Input from Equipment Check is Active
14
(continued)

LED COLOR INDICATION
Thermostat LED’s (4 Positions)
R Red 24 VAC available to Thermostat
Y1 Yellow Thermostat First Stage Compressor Call
Y2 Yellow Thermostat Second Stage Compressor Call
W1/E/AX1 White Thermostat Call for W1 or E or AX1
W2/AX2 White Thermostat Call for W2 or AX2
O/B/W3 Yellow Thermostat Call for O, B or W3
G Green Thermostat Fan Call
Damper LED’s (4 Positions)
Power Close / Power Open Red / Green Red On Damper Closed; Green on Damper Open
No light when wiring short detected
Fire Alarm LED
Fire Indication Red Fire Terminals Active - Panel is Shut Down
15
In addition to LED’s, the expandable zone panel has a full function built-in backlit display panel that provides
information on the current operations of the zone panel. When the expandable zone panel is running in normal
operation, the display is updated continuously to show the system operating parameters. The system will show
the following status screens on the display.
Number of Heat Calls currently being serviced. Check the panel
LED if it is necessary to determine exactly which zones are calling
for heat operation. If Auxiliary Heat or Emergency Heat calls are
active, the display will replace heat calls with Auxiliary or
Emergency Heat Calls.
Number of Cool Calls currently being serviced. Check the panel
LED if it is necessary to determine exactly which zones are calling
for cooling operation.

Number of Fan Calls currently being serviced. Check the panel
LED if it is necessary to determine exactly which zones are
calling for Fan Operation.
16
Equipment Plenum Temperature is displayed. When the included
plenum air temperature sensor is installed, the zone panel will
display the Plenum temperature in the range of 30 - 200˚ F.
Plenum Temperatures outside this range indicate an equipment error.
See Section 7 Error Conditions for a further explanation.
NOTES: When no zones are calling, the panel will command
all dampers to open.
• For maximum energy conservation, a purge will occur at the
end of each call.
• No calls will be answered until the purge is complete.
• Equipment staging is automatic based on time and plenum
temperature.
• Dampers will not close and staging will not occur if the plenum
temperature sensor is enabled but not connected or
functioning properly.
Emergency Heat Selection (Multi-stage Heat Pump Systems Only)
Emergency Heat can be selected at the main panel or from a Heat Pump Thermostat wired to the main panel.
No cooling calls will be answered if emergency heat is switched on.
To select Emergency Heat from the main panel:
1. Press and release the EM HEAT button located below the main display.
2. The display will update from HEAT CALLS to EM HEAT CALLS and will show COOL DISABLE to indicate that
no compressor calls will be answered.
3. To stop Emergency Heat, press the EM HEAT button again.
4. The display will update from EM HEAT CALLS to HEAT CALLS and COOL CALLS will return.
To select Emergency Heat from a thermostat
1. Set Emergency Heat Thermostat to Emergency Heat switch position (only one thermostat can
control Emergency Heat)
2. Raise heat setting on Emergency Heat Thermostat to create Emergency Heat call.
3. The zone panel display will update from HEAT CALLS to EM HEAT CALLS and will show COOL DISABLE to
indicate that no compressor calls will be answered.
4. To stop Emergency Heat, set the Emergency Heat Thermostat to a non-emergency heat position or
lower the temperature on the Emergency Heat Thermostat to end the emergency heat call.
5. The zone panel display will update from EM HEAT CALLS to HEAT CALLS and COOL CALLS.
NOTE: Configuration setting number 20 in section 4 selects which thermostat is used to activate Emergency Heat.

Error Conditions
7
The zone panel continually monitors various components of the
zone system and will display a message when the following
monitored conditions are detected.
Cooling is disabled when Emergency Heat has been
selected on a heat pump system
Selecting emergency heat from a thermostat (See Installer
Option 20) in heat mode will disable compressor cooling in all
zones. The zone panel will display the following message when
Cooling has been disabled. To enable cooling, turn Emergency Heat
Off at the panel and/or the priority thermostat calling for emergency
heat and make a call other than emergency heat from the
priority thermostat.
Plenum HI Run Delay HI Limit
Displayed when the Plenum Temperature is exceeded during
equipment heating operation. All heating stages will be turned off
and the fan will be turned on until the plenum temperature returns
to the normal range. Service the system immediately to prevent
potential damage.
17
Plenum LO Run Delay LO Limit
Displayed when the Plenum Temperature is too low during
equipment cooling operation. All cooling stages will be turned off
and the fan will be turned on until the plenum temperature returns
to the normal range. Service the system immediately to prevent
potential damage.
Plenum Sensor Bad
Displayed when an error has been detected with the plenum
sensor. This error must be corrected by servicing the zone panel
plenum sensor. If the sensor is not operating correctly, the zone
panel will not call for additional stages of heating or cooling.

Outdoor Sensor Bad
Displayed when an error has been detected with the outdoor
sensor. This error must be corrected by servicing the zone panel
outdoor sensor. If the outdoor sensor is not operating correctly, the
zone panel will not use outdoor balance point control for
heating calls.
Invalid Address on Expansion Panel
Displayed when an invalid address has been set on an expansion
panel. This message will appear when an expander is powered up
and wired to the communication terminals. To locate the expander
panel with the invalid address, view the expander panel status LED.
The status LED will be flashing red.
18
Duplicate Address on Expansion Panel
Displayed when a duplicate address has been set on an expansion
panel. This message will appear when an expander is powered up
and wired to the communication terminals. To locate the expander
panel with the duplicate, view the expander panel status LED.
The status LED will be flashing red.

Adding More Zones
8
The zone panel can be expanded to up to 32 zones with 4 zones on the main panel and 28 total expansion
zones. Additional zones must have power and communication wires to be recognized and controlled by the
main panel. To add more zones, complete all wiring, follow instructions included with expander panel and
start the main panel test mode.
Start the panel test mode to add additional zones:
1. Ensure all zones are installed, zone addresses are set, wiring
is complete and power is applied to the main panel and
expansion panels.
2. Press TEST on main panel for 3 seconds and release.
3. Press SELECT once for each new zone added. New zones must be
added in blocks of two. NOTE: After second new zone is added,
Expander LED will change from Red to Green, and ZONE OK will
appear on the main panel display.
4. If new zones do not appear, check wiring and ensure expansion
zones have power.
5. Press HOLD FOR EXIT for 3 seconds to complete adding zones.
The expansion zones may be wired to either the top or bottom communication terminals on the main panel
or to the top or bottom communication terminals on the expansion panel. This wiring flexibility allows the
installer to choose the most flexible, cost effective wiring for the installation.
Each expansion panel must have a 5 Wire connection for proper communication. It is not necessary to use
shielded wire for the panel to panel connection. 18 - 20 Gauge solid thermostat wire or similar is acceptable.
When wiring the expansion panel(s) be sure to connect the terminals from one panel to the next using the
following terminal connections.
19
Main Panel to Expansion Panel
COM1 COM1
COM2 COM2
GND GND
COM3 COM3
COM4 COM4
Expansion Panel to Expansion Panel
COM1 COM1
COM2 COM2
GND GND
COM3 COM3
COM4 COM4
MAIN Panel to Expander Expander to Expander

Example Wiring Options
20
Main Panel
Expander Panel
Zones 5-6
Expander Panel
Zones 7-8
Expander Panel
As Needed
Daisy Chain All Zones
Located at Main Panel
Star Wiring All Zones
Located at Main Panel
Main Panel
Expander Panel
Zones 7-8
Expander Panel
Zones 5-6
Expander Panel
As Needed
Expander Panel
As Needed