Bravat F14691C User manual

F14691C/F14691NE
Model F14691C/F14691NE
Description Single Lever Lavatory Faucet
A
INSTALLATION DIMENSIONS
PRODUCTS INSTALLATION INSTRUCTIONS
GF4354/A1/20110726 Service Hot Line 8008205330
Unit :mm
:mm
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Nut
Hexagon Wrench
1
1
1
1
1
1
1
1
1
1
1
1
1
2
Supply Hose
Mounting Stud
Retaining Plate
Rubber Washer
O
35
C
C
35Cartridge
Socket Head Screw
Aerator
O-ring
Cartridge Nut
Dome
Handle
Button
M4 Screw
1
1
O
O-ring
Connector
1
1
Special Wrench
Guangzhou bathone industrial Co., Ltd.
45
Ø 68
MAX50
Ø 32
HOT
COLD
CLOSE
OPEN
25°
MAX450
Ø42
MAX25 2-Ø35
2-G1/2
100° 8°
127
211
188

B
HELPFUL TOOLS
FAUCET INSTALLATION STEP
C
Flashlight
Points for attention before installation
Before installing the new mixer, it is essential that you thoroughly flush
through the supply pipes in order to remove any remaining swarf,
solder or other impurities. Failure to carry out this simple procedure
could cause problems or damage to the workings of the mixer.
If the pictures and statements in the ‘Installation Specifications’ is
unconfirmed with practicality,please take practicality as standard.
Adjustable Wrench
Work water pressure: Min.0.5kgf/cm2/ Max. 5kgf/cm2.(Including cold
and hot)
GF4354/A1/20110726 Service Hot Line 8008205330
3
Hot Cold
13
14
15
10
3.Connect Supply Hose to Cold Valves and Hot
Valves. Turn on Water Supplies and check all
connections for leaks.
(Cold Valves and Hot Valves are self-prepared. )
16 16
1.Supply Hose through the center hole and
O-Ring first, Then install the
Valve Body
13 14
10 15
2.Assemble Rubber Washer , Retaining
Plate
onto Mounting Stud from
Underside of basin, tighten Nut .
(NOTE: DON’T OVER TIGHTEN NUT TO
PREVENT DAMAGE OR CRACK OF
PRODUCT)
13
10
14
15
16
9
1
9
9
1
1
Guangzhou bathone industrial Co., Ltd.

POP-UP INSTALLATION STEP
D
GF4354/A1/20110726 Service Hot Line 8008205330
1
2
3
4
5
Drain body
Mounting nut
Rubber washer
Gasket
Drain plug 1
1
1
1
1
Close drainage
Open drainage
2. Press down pop-up to close drainage.lift
pop-up to open drainage.
6Rubber washer 1
7
Mounting nut 1
8
Liner 1
(Note: Don’t overtighten nut or basin may be crack.)
Nut.
Nut(5) onto Drain Body from underside, tighten
3. Assemble Gasket(3), Rubber Washer(4) and
2. Insert Drain Body into basin mounting hole.
1. Disassemble Nut(8), Rubber Washer(4) and
Gasket(3).
4. The sealing Rubber Washer(6), liner(7)set into
The nut(8) ,tighten Nut.
Guangzhou bathone industrial Co., Ltd.

FAUCET AND POP-UP OPERATION
E
F
MAINTENANCE
CAUTION: Always turn water OFF before removing existing or
disassembing the faucet. Open faucet handles to
relieve water pressure and insure that complete water
shut-off has been accomplished.
To keep the surface clean and bright, please clean
the faucet regularly,please abide by the following
procedures:
1. Use rinsing water and soft cloth, clean bilge and bilge
membrane on the surface to the best of the abilities.
2. Cleaned the residua with the following cleansers only.
Soft liquid cleanser.
Colorless glass cleanser, totally soluble powder cleanser
without abrasive capability.(Mixed by instructions.)
No abrasive cleansers waxes
Never use cleanser, emery cloth or handkerchief which can
rub.
Never use cleaners containing abrasive cleansers,
ammonia,bleach, acids, waxes, alcohol, solvents or other
products not recommended for chrome.
3. After cleaning, use rinsing water to clean all cleanser
immediately and drying with a soft cotton cloth.
4. Carefully dismantle the aerator regularly, rinse under clean
running water until any loose debris is cleared to avoid the
influence to water outflow.
Open
Close
(Hot) (Cold)
1.Pull Right Handle to turn on water, and down
to turn off.
2.Turn Handle towards side with red mark to
adjust hot water volume, and towards side
with blue mark to adjust cold water.
GF4354/A1/20110726 Service Hot Line 8008205330
Guangzhou bathone industrial Co., Ltd.