Bredenoord ESaver III User manual

© Bredenoord Aggregaten 2017
Operation manual
|www.bredenoord.com
Bredenoord bv Rental - Postbus 20122 - 7302 HC Apeldoorn - Zutphensestraat 319 - 7325 WT Apeldoorn
Tel. [phone] - Fax [phone] - www.bredenoord.com - rent[email protected]om
Controller type: Mitsubishi PLC
ESaver III
R0095 - R0109
15

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 2
Inhoud
1................................................................................................................................... 3
Verkorte bedieningshandleiding
2................................................................................................................................... 4
Connection of the ESaver
................................................................................................................................... 42.1 Electrical connections
................................................................................................................................... 42.2 Connecting power cables
3................................................................................................................................... 5
Operating instructions
................................................................................................................................... 53.1 Starting and stopping
................................................................................................................................... 53.2 Main display
................................................................................................................................... 83.3 Reading data
................................................................................................................................... 103.4 Timer ................................................................................................................................... 113.5 Testing diesel genset
4................................................................................................................................... 13
Construction
................................................................................................................................... 0
EG-verklaring van overeenstemming IIA

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 3
1Verkorte bedieningshandleiding
ESaver III
R0095 - R0109
15 kVA

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 4
2Connection of the ESaver
This chapter describes how the power cables have to be connected.
2.1 Electrical connections
When using a genset with the ESaver it should be attempted to connect the installation according to the TN
system. For more information about earthing please consult the national applicable standards and regulations.
Below a schematic of a TN system is shown.
In the schematic is shown that the neutral and earth connection of the generator are directly earthed. When no
earthing is available this is done by placing an earth pin.
The connection of the ESaver should be done by a certified installation company.
Only connect the ESaver when it´s switched safely.
The ESaver provides electricity with a clockwise rotation field by means of 3 phase connection: L1, L2, L3 and
N. Connect the load(s) according to EN-50110 and keep the following points in mind during connection:
·Only connect approved cables to the ESaver.
·Only attach cables via the cable input. The door should be closed during operation.
2.2 Connecting power cables
The ESaver works only with a clockwise rotation field!

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 5
3Operating instructions
This chapter discusses the operating instructions of the ESaver.
3.1 Starting and stopping
Starting
·Ensure that the diesel genset can automatically start by means of the connector (5)
(see operation manual diesel genset or start-stop module)
·Turn the selector switch (1) to “ON”.
·Press the button "START" (2). The ESaver starts!
·Switch on the main switch (4)
Stopping
·Switch off the main switch (4)
·Press the button "STOP" (3). The ESaver stops!
·Turn the selector switch (1) to “OFF”
Alarm reset
·Turn the selector switch (1) to “OFF”
·Turn the selector switch (1) to “ON”
·Press the button "START" (2). The ESaver starts!
·Switch on the main switch (4)
3.2 Main display
In this chapter the main stucture will be explained with additional information about the main display.
In the main display are several symbols displayed which can be selected by pressing. These symbols are
provide with .
By pressing the symbol a new display wil appear with the data of this device.
By pressing "START" in the main display the ESaver will start up.

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 6
Main display
ESaver in operation

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 7
Display "Genset"
Display "Battery status"
Display "Consumer"

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 8
3.3 Reading data
·Turn the selector switch (A) to “ON”.
1. Touchscreen (see below)
2. Battery monitor
Press arrow button (B), for toggling between displays.
Press "LOG" (9) and "ACCU"(10) willl open an new display.
3. Power genset
4. Status ESaver
5. Power consumer
6. Battery status
7. Important events
8. Reset error
9. Log (history list)
10.Battery (use of battery)
Important events
Important events
Only important event will be triggered and displayed.
Below is showed which events will be displayed.
Timers
Cooling: Duration of the time when the genset is
running in cool down mode.
Peak: Duration of the time the genset keeps
running if no peak start is no longer offered.
Countdown: This time varies depending on battery
status (%). Countdown will start when the power
stays between certain values
Start L1/2/3: Shows on which phase the peakstart is
occured.
Battery synch: Is shown when the battery is
synchronising and how long this will continue.

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 9
Log (history list)
Battery (use of battery)
With pressing button (B) the next display will appear.
Press "Week timer" will open a new display.
9. ESaver in operation
10. Generator running hours
11. Supplied energy
12. Charge cycle battery
13. Time till next service
14. Weektimer

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 10
3.4 Timer
Timer for genset
1. Switch on/switch off timer
2. Switch on genset manually, works only when inverters and timer are switched on
3. Switch off genset manually
4. Set clock
5. Switch on point or switch off point
6. Adjust switch time (hours), press the hour indication
7. Adjust switch time (minutes), press the minute indication
Normal functioning timer:
At the switch on point (example 8:00 hour) the diesel genset starts. At the switch off point (example
21:00 hour) the diesel genset stops.
Manually starting with button 2, for example if the work once begins earlier or if the settings of the timer are
modified:
The diesel genset starts manually. At the switch off point (example 21:00 hour) the diesel genset
stops.

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 11
Manually stopping with button 3, for example if the work once stops earlier or if the settings of the timer are
modified:
At the switch on point (example 8:00 hour) the diesel genset starts. Then the diesel genset stops
manually. On the next switch on point the diesel genset starts again.
3.5 Testing diesel genset
·Turn the selector switch (1) to “ON”.
·Start the ESaver
·Press arrow button, untill picture D will appear in
the display.
·Press "START" button (2).

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 12
·One smiley will appear if the genset is connected correctly.
·After this the charging will be checked ("Checking charging
please wait").
·When the genset works correctly a
second smiley will appear.
·The remark ("Link generator OK") will
appear.

Volledige bedieningshandleiding 2
© Bredenoord Aggregaten 2017 13
4 Construction
Front
Back
1. Selector switch
2. Touch screen
3. Battery monitor
4. Emergency stop
5. Inverters