Bredenoord ESaver III User manual

© Bredenoord Aggregaten 2013
Shortened operation manual
ESaver III
HAH0003 - HAH0012
15 kVA
Controller type: Mitsubishi PLC
Bredenoord Aggregaten BV - Zutphensestraat 319, 7325 WT Apeldoorn - Postbus 20122, 7302 HC Apeldoorn
T + 31 (0) 55 301 85 01 - F + 31 (0) 55 301 85 00 - E inf[email protected]om
|www.bredenoord.com

Shortened operation manual version 2.4.0
© Bredenoord Aggregaten 2013 2
1 Connection of the ESaver
This chapter describes how the power cables have to be connected.
1.1 Connecting power cables
The ESaver works only with a clockwise rotation field!

Shortened operation manual version 2.4.0
© Bredenoord Aggregaten 2013 3
2 Operating instructions
This chapter discusses the operating instructions of the ESaver.
2.1 Starting and stopping
Starting
Ensure that the diesel genset can automatically start by means of the connector (5)
(see operation manual diesel genset or start-stop module)
Turn the selector switch (1) to “ON”
Press the button "START" (2). The ESaver starts!
Switch on the main switch (4)
Stopping
Switch off the main switch (4)
Press the button "STOP" (3). The ESaver stops!
Turn the selector switch (1) to “OFF”
Alarm reset
Turn the selector switch (1) to “OFF”
Turn the selector switch (1) to “ON”
Press the button "START" (2). The ESaver starts!
Switch on the main switch (4)

Shortened operation manual version 2.4.0
© Bredenoord Aggregaten 2013 4
2.2 Testing diesel genset
Turn the selector switch (1) to “ON”
Start the ESaver
Press the arrow buttons, so that screen D appears
Press the button "START" (2)
Screen E appears ("Controle laden even geduld")
If the diesel genset is working properly, screen F appears ("Koppeling aggregaat OK")

Shortened operation manual version 2.4.0
© Bredenoord Aggregaten 2013 5
3 Reading data
Turn the selector switch (A) to “ON”
1. Touch screen (see below)
2. Battery monitor
Press the arrow buttons (B) so that the screens - indicated below - appears.
Screen with alarms
3. Power genset
4. Status ESaver
5. Power user
6. Battery status
7. Alarms
8. Timer genset
9. Running hours ESaver
10.Running hours genset
11.Charge cycles battery

Shortened operation manual version 2.4.0
© Bredenoord Aggregaten 2013 6
4 Construction
Front
Back
1. Selector switch
2. Touch screen
3. Battery monitor
4. Emergency stop
5. Inverters

Shortened operation manual version 2.4.0
© Bredenoord Aggregaten 2013 7
5 Timer
Timer for genset
1. Switch on/switch off timer
2. Switch on genset manually, works only when inverters and timer are switched on
3. Switch off genset manually
4. Set clock
5. Switch on point or switch off point
6. Adjust switch time (hours), press the hour indication
7. Adjust switch time (minutes), press the minute indication
Normal functioning timer:
At the switch on point (example 8:00 hour) the diesel genset starts. At the switch off point (example
21:00 hour) the diesel genset stops.

Shortened operation manual version 2.4.0
© Bredenoord Aggregaten 2013 8
Manually starting with button 2, for example if the work once begins earlier or if the settings of the timer are
modified:
The diesel genset starts manually. At the switch off point (example 21:00 hour) the diesel genset
stops.
Manually stopping with button 3, for example if the work once stops earlier or if the settings of the timer are
modified:
At the switch on point (example 8:00 hour) the diesel genset starts. Then the diesel genset stops
manually. On the next switch on point the diesel genset starts again.