Brickcom OB-100A User manual

Megapixel Day & Night
Outdoor Bullet Network Camera
OB-100A V2 Series
OB-100A/WOB-100A/GOB-100A
Quick Installation Guide
Quality Service Group

Read Before You Use
1. Power off the camera device
immediately if it starts smoking or
smells unusual.
2. Power off the camera device
immediately if the camera is
exposed to rain or liquid.
3. Do not set the camera device near
any heat sources. (Ex: television and
oven)
4. Keep the camera device away from
direct sunlight.
5. Do not set the camera device over
the specific operating temperature.

6. Do not set the camera device in any
wet and humid environments.
7. Do not set the camera device on
unsteady surfaces.
8. Do not attempt to dismantle the
camera device.
9. Do not drop or hit the camera device.
10. Do not use the camera device when
there is lightning.

1. Check Package Contents
A. Camera Package contents
a. OB-100A b. Shielding Cover
c. Screws Bag d. Product CD
e. Warranty Card / Easy Installation
Guide
f. 2 Water Proof Connectors
g. Dry Bag h. High Power PoE (Optional)
i. Bracket (Optional) j. Bracket Assembly Plate (Optional)
k. Wi-Fi Dual Band Antenna package
(Optional)
i. 3G Antenna package (Optional)

B. Wi-Fi Antenna Package contents (optional)
Refer to the installation guide included in the package when installing the
Wi-Fi antenna.
a. Wi-Fi Dual Band Antenna
b. Extension Cable
c. Surge Arrestor Kit
d. Mount Kit
C. 3G Antenna Package contents (optional)
Refer to the installation guide included in the package when installing the
3G antenna.
a. 3G Antenna
b. Extension Cable
c. Surge Arrestor Kit
d. Mount Kit

2. Device Description
<Front Panel>
<Rear Panel>
< Top>
Lens
IR LED
Light Sensor
Ventilation Hole
Shielding Cover
Screw Holes

< Bottom>
< Side >
Screw Holes Secure Hole
RJ45 Connector 2
Antenna Connector
Secure Hole
RJ45 Connector 1
Micro SD/SDHC Card Slot
3G SIM Card Slot

3. Installation
WARNING: Do not mount the camera on a soft material. The camera may
fall and be damaged.
Hardware Installation
1 Micro SD/SDHC Card and 3G SIM Card Installation
1.1 Remove the Lens cover from the Bullet Camera.
1.2 Inset the Micro SD/SDHC card and 3G SIM card(*) into their
respective slots.
1.3 Place a dry bag onto the camera device.

1.4 Reattach the Lens cover and secure the cover to the top of the
camera device using two screws.

2 Wall Installation Using the Optional Bracket
2.1 Using the Bracket plate as a guide, drill three holes into the wall and
hammer the supplied plastic anchors into the three holes. Use a
screwdriver and the supplied screws to secure the plate to the wall.
2.2 Attach the Bracket Assembly Plate to the bottom of the camera using
two screws.
2.3 (1) Use the two supplied screws to secure the bracket to the side of
the camera. (2) Push back the spring on the mortise lock and hook
the camera and attached bracket onto the groove of the wall mount
bracket as shown in the diagram.

2.4 Connect (1) the POE cable; (2) DIDO, Audio In/Out, RS485 cable;
and (3) Antenna cable with the camera. Refer to step 4 for more
details installation information.
2.5 Secure the two screws on the wall mount bracket.
2.6 Place the wall mount bracket on the plate and attach it using the
supplied screws. Adjust the angle of the wall mount bracket
towards the area to be monitored.

3 DIDO, Audio In/Out, RS485, and Antenna Connection
3.1 PoE Connection
For the Power over Ethernet connection, construct the PoE cable
using the pin definitions of the RJ45 connector below and refer to
step 5 for instructions on how to install the Water Proof Connector.
Once the PoE cable has been constructed using the waterproof
connector, pass the RJ-45 cable from the camera through the bracket
and connect it to the PoE cable.
RJ45 Connector 1
Pin No.
Function
Pin 1 Transmit Out+ (Tx+)
Pin 2 Transmit Out- (Tx-)
Pin 3 Receive In+ (Rx+)
Pin 4 DC 48V
Pin 5 DC 48V
Pin 6 Receive In- (Rx-)
Pin 7 48V_GND
Pin 8 48V_GND

3.2 DIDO, Audio In/Out, RS485 Cable Connection
For the DIDO,Audio In/Out and RS485 cable connection, construct
an Ethernet cable using the pin definitions of the RJ-45 connector
below and refer to step 5 for instructions on how to install the Water
Proof Connector. Once the Ethernet cable has been constructed
using the waterproof connector, pass the cable through the bracket
and connect it to the RJ-45 connector at the bottom of the camera.
3.3 WiFi or 3G Antenna Extension Cable Connection
Pass the Antenna extension cable through and bracket and connect it
to the Antenna connector at the bottom of the camera.
RJ45 Connector 2
Pin No.
Function
Pin 1 Power +4.5V
Pin 2 Digital Output
Pin 3 Digital Input
Pin 4 Ground
Pin 5 RS-485-
Pin 6 RS-485+
Pin 7 Audio-in
Pin 8 Audio-out

4 Water Proof Connector
Refer to the installation guide included in the package when installing
the Water Proof connector
4.1 Insert the stripped cable through the sealing nut and the housing.
Clamp the cable with an RJ45 plug.
4.2 Push the RJ45 plug into the housing and secure the sealing nut
tightly.
4.3 Attach the gasket to the front of the housing.
4.4 Connect the Ethernet cable to the RJ45 cable.
4.5 Secure the connectors tightly.

5 Camera Connection
The OB-100A is PoE compliant, so there are two options for connecting
the camera to a power and Ethernet source. The camera can either be
connected to a PoE-enabled switch or a non-PoE switch.
A. If using a PoE-enabled switch:
i. Use a single Ethernet cable to connect the camera to the
PoE-enabled switch.
B. If using a non-PoE switch:
i. Use a standard RJ-45 cable to connect the camera to a PoE
Injector.
ii. Use a standard RJ-45 cable to connect the PoE Injector to the
non-PoE switch.
iii. Use a standard power cable to connect the PoE Injector to a
power outlet.

C. If using a PoE injector as power input (For GOB-100A,
WOB-100A):
i. Use a standard RJ-45 cable to connect the camera to a PoE
Injector.
ii. Use a standard power cable to connect the PoE Injector to a
power outlet.

4. Setup the Network Camera
1. Insert the Installation CD into the CD-ROM driver. Run Auto-Run Tool
directly from the CD-ROM to start the installation. When installing the
Brickcom software kit for the first time, select a desired language for the
interface. The available languages are listed in the scroll box. Click
<Install> and follow the steps to install the EasyConfig wizard on the
desired computer.
Please follow the instruction of the InstallShield Wizard to finish the
Brickcom Software Kit installation.

2. To launch EasyConfig or PC-NVR Standard, select the application and
click <Finish>. When launching the PC-NVR program, please refer to
the PC-NVR user manual.

EasyConfig
To launch EasyConfig, select EasyConfig from the start menu. If Complete
Setup type was used in the software installation, an EasyConfig icon was
installed on the desktop. Double click to open the icon.
If Custom Setup type was used in the software installation and an EasyConfig
icon was not installed on the desktop, the program will be installed under
C:\Program Files\Brickcom\EasyConfig unless the program was saved to a
preferred directory.
1. Click <Start> to continue. The program will automatically search
for the camera in the intranet.
NOTE - Check “Skip the hardware installation guide” to skip checking the
hardware connection. To check the hardware installation settings, do not
check the option box.