Bridgetek PanL PC0011 User manual

PC0011 Mood Lighting (ML)
DALI/DMX 512 Controller
Quick Start Guide
1. To securely mount the device on a flat surface, M4 screws and nuts
can be applied at the slots at the side of the enclosure. (Not provided
in the box)
2. If connecting multiple ML Controllers to the same PanL Hub port in a
daisy chain configuration, set the ID switch. Refer to the section - ID
Switch Configuration for details.
3. Connect RJ45 cable and add a terminator. Refer to the section PanL
Hub Connection for details.
4. If using DMX, refer to PanL DMX Setup for details.
5. If using DALI, refer to PanL DALI Setup for details.
For multiple PanL ML Controller connections to a single PanL Hub port, the ID
switch must be configured to be unique. Using a Philip head screw driver, set
a unique number for each device between 0-7 (do not use 8-9). For example,
if connecting 3 PanL ML Controllers to a PanL Hub port, you may set it as 0,
1, and 2. PanL ML Controllers connected to different PanL Hub ports can share
the same unique number.
The PanL ML Controller is designed to be connected to a PanL Hub for power
and data via the P1 or P2 RJ45 ports. When a single PanL ML Controller is
connected to a PanL Hub port, the maximum length of the RJ45 cable shall
not exceed 100 meters. Connect the terminator (provided in the PanL Hub
package) to the unconnected P1 or P2 port.
For multiple PanL ML Controller connections to a single PanL Hub port, the
first connection to PanL Hub and the subsequent connections in between the
PanL ML Controller devices must not exceed 50 meters in cable length, each.
The total combined cable lengths must not exceed 100 meters. Connect the
terminator provided in PanL Hub box to the last unconnected PanL ML
Controller P1 or P2 port.
.
Product Features
PanL ML Controller
PanL ML Controller Setup
ID Switch Configuration
Please visit http://panlshop.com/warranty or scan the QR code for warranty
registration with the UUID and Product Key below:
STICKER AREA
PanL DMX Setup
Connect a RJ45 cable from the PanL ML Controller port labelled DMX 512 to
the first DMX decoder and connect a DMX terminator to the last unused
decoder port as illustrated in the example below. The PanL ML Controller
supports up to 512 DMX channels. Depending on the number of channel(s)
per decoder used, the cumulative channels must not exceed 512 for all
connected decoders. Please refer to the Decoder’s datasheet for any cable
length specifications.
1
Power Indicator
2
RJ45 Ports –Connect to PanL PH44/80 Hub, another PanL
Device or Terminator
3
ID Switch –Refer to the ID Switch Configuration section for
more details
4
LED Status Indicator - Refer to the DALI/DMX ML Controller
LED Status Indicator section for more details
5
USB –Reserved for factory use only
6
SWD –Reserved for factory use only
7
Reset Button
8
DMX Connection –Refer to the PanL DMX Setup
9
DALI Connection –Refer to the PanL DALI Setup
PanL Hub Connection
PanL DALI Setup
Connect the DALI bus wires to the two DA terminals on PanL ML Controller
and tighten the screws for a secure connection. The DALI bus is polarity free
and so the two wires may be connected to either port. The recommended
maximum length of the bus is 300 meters when AWG16 standard 2core wire
in single cable or cable conduit is used. PanL ML Controller supports up to
64 DALI drivers. An external DALI bus power supply is required as illustrated
below:

DALI / DMX ML Controller LED Status Indicator
PC0011 Mood Lighting (ML)
DALI/DMX 512 Controller
Quick Start Guide
* - LED blinks during data transfer
** - LED blinks twice a second (2Hz rate)
Normal Function
Status
System Status
(1)
Communications
(2)
DALI Status
(A)
DMX Status
(B)
Power On Status
Red
Red
Red
Red
Boot Success
Green
Red
Off
Off
No Communication
Green
Red
Off
Off
Communication
Green
Green*
Off
Off
DALI Data Transfer
Green
Green*
Green*
Off
DMX Data Transfer
Green
Green*
Off
Green*
Discover in Progress
Green
Green*
Green
Off
Failsafe Status
System Status
(1)
Communications
(2)
DALI Status
(A)
DMX Status
(B)
Power On Status
Red**
Off
Off
Off
Boot Success
Red**
Off
Off
Off
No Communication
Red**
Red
Off
Off
Communication
Off
Green*
Off
Off
Waiting for Recovery
Red<->
Green**
Green*
Off
Off
Discover in Progress
Red<->
Yellow**
Green*
Off
Off
Recovery Done
Green**
Green**
Off
Off