BRIGHT Home 600 User manual

Home 600
User manual & quick setup guide

0% 20% 40% 60% 100%
0% 20% 40% 60% 100%
X 30
2 3
Box content
Indication lights
Ports & buttons
button
Solar port
Lamp power ports 3x
USB ports 2x
0% 20% 40% 60% 100%
0% 20% 40% 60% 100%
0%
25%1%
25%
50%
50%
75%
75%
100% Blinking
100% 100%
Battery level
Charge rate
Excess
energy
System on (Green light)
Power status Low battery
30 min left: No USB power.
Box content
Nails Cable
clamps
Control unit & bracket Solar panel & mounting wire
Ceiling
hooks
Splitter
Micro-USB cable
Tube light & bracket 1x
User manual
x 28 x 30 x 3
Fixed-focus lamp 3x
2x

20% 40% 60% 100%
20% 40% 60% 100%
4 5
Step by step
Installation guide
Test lamps
Switching lamps on: Press switch to move between light levels
Switching tube light on: Press switch to move between light levels
After 5 seconds
without pressing
the switch, the next
press will always
turn OFF the light.
Test lamps and switches
Test tube lights and switches
Turn off system
Press and hold power button for 2 seconds:
Complete system shut down
No light and USB power
Check that the
battery is charged
– minimum
2Plug in lamp
cables firmly
3
Turn on system
1
4
5
6

3
21
CAUTION:
Place control
unit in a dry
and protected
location
6 7
STEP 1 Find placement for control unit and solar panel
• Find the most sunny place to install the panel
Check if the panel is correctly facing the sun by plugging the panel to the control unit (full sun icon)
• Bring a friend to help you – one on roof and one inside the house
• Be careful when mounting the panel on the roof
STEP 2 Install panel
1. Use the wires to fasten the panel
Use the included nails if needed
2. Install panel facing the sun
3. Pull the cable inside the house
Allow water
to drip
from cable
Make sure the solar panel
is securely fastened.
Holes in the roof might
cause leakage.
CAUTION:

0% 20% 40% 60% 100%
8 9
STEP 3 Install bracket and control unit
1. Find a secure wall suitable for fastening the bracket
2. Fasten bracket securely as shown
3. Attach the control unit
2
3
1
YES NO
Make sure the bracket and
control unit are securely fastened.
CAUTION:
STEP 4 Place lamps
Place the lamps where you want them.
Fixed-focus lamps can be mounted in the ceiling and to the wall.
Ceiling lamp
Use ceiling hooks to mount
lamp in the ceiling
Wall lamp
Use ceiling hooks to mount
lamp(s) to the wall
Tube light
Mark correct nail position
and hammer nails to the wall
Attach bracket to the tube
light and place it on the nails

1
2
10 11
STEP 5 Place light switches and plug in lamps
1. Mount the cables and swithces to the wall
2. Plug the lamps into the control unit
Do not damage the cable!
CAUTION:

14 1
•Maintenance
•Troubleshooting
•Technical info
•Warranty
Care and maintenance Troubleshooting
• Regularly wipe the solar panel to clean from dust
and dirt using a soft cloth. Do not use chemicals!
• Regularily check if connectors are securely pressed
into the control unit to ensure water proofing
• Regularily check cables and hooks for damage.
• Regularily check if lamp bulbs are clean.
• Regularily check if bracket, control unit, lamps,
switches and junctions are securily mounted.
It’s sunny, but the charge level is low
1. Check if anything is shadowing the solar panel
2. Check if the solar panel is mounted facing the sun
3. Clean the solar panel
Can’t change the light level
1. Press the switch several times within 3 seconds
2. Ensure the battery is charged
3. Check that the control unit is ON
Lights don’t work
1. Check if the control unit power button light is on
2. Check if the battery is charged
3. Check if the lamps are plugged in correctly
If problems cannot be solved please contact you
sales agent.
The light source contained in this luminaire shall only be replaced by
the manufacturer or his service agent or a similar qualified person.

1 1
Technical info
Battery
Battery type: LiFePO4
Battery capacity: 58 Wh
(6,000 mAh at 9.6 V)
Battery lifespan: 5-7 year
(2,000 full charge cycles)
Advanced circuit protection
Power
Solar panel type: polycrystalline
Solar panel output: 20 Wp at 8 V
MPPT technology for optimized charge
6 m solar cable
Materials
ABS, PP, PC, TPE, steel
The battery is made to last 2,000
full charge cycles or 5–7 years.
Batteries must be replaced or
upgraded by a qualified agent.
Charge time
(depending on sun conditions)
7 h+
Full battery run time
Phone charging will reduce the run time of the
product’s light.
Cable lenghts:
Solar panel cable: ........................ 6 m
Fixed focal lamp cable: .......... 5 + 2 m
Tube light cable: ........................... 5 + 2 m
Splitter cable: ................................... 4 m
Switch cable: ..................................... 1.5 m
Warranty card
Retailer name
Retailer phone
Date of purchase
Serial number
Retailer stamp or signature
If your product stops working within 2 years of purchase, simply return it along with this stamped and dated warranty
card to your retailer for repair or replacement. This warranty covers product failure from normal use and is void if the
product has been tampered with, repaired by unauthorised repairer, modified, submerged in water or in case of misuse.
7 h+ 4 lamps on high (760 lm total)
15 h+ 3 lamps on medium, 1 tube light on low
(260 lm total)
20 h+ 3 lamps on low, 1 tube light on low
(230 lm total)

1 1
Warranty
Limited Product Warranty for BRIGHT
Home
BRIGHT PRODUCTS AS warrants that
the product has been carefully tested,
inspected and left the Factory in a proper
working condition, free of visible defects.
BRIGHT PRODUCTS AS warrants the
product to be free from defects in material
and workmanship, under normal use and
operation:
For the main components. (Solar panel,
Control unit and Lamps) for a period of two
(2) years after the date of sale/handover
to customer
”The product” in this warranty is defined
as BRIGHT Home 600 and accessories
included in the original packaging.
The warranty is limited to the free
replacement of the defective main part(-s)
or replacement of the entire product during
the two years of warranty. Defective parts/
products replaced under this warranty
shall become the property of BRIGHT
PRODUCTS.
The above stated Warranty is subject to
the following conditions:
Products are sold by authorized BRIGHT
PRODUCTS AS representatives. The
products are operated and maintained
in accordance with BRIGHT PRODUCTS
operating instructions, maintenance
instructions and specifications. Utilization
of only BRIGHT PRODUCTS AS authorized
parts and accessories. The warranty shall
not apply to damages resulting from normal
wear and tear of product use, nor shall
it apply to any product, which has been
subject to damages, alterations or misuse
by the purchaser. Parts of the product,
which would be generally considered as
expendable service items during normal
use, such as cardboard box/packaging
items, instruction manual etc., are not
covered by the warranty.
The USB mobile phone charger is made to
support most commonly available mobile
phones based on their current/known
specifications for charging current and
-accessories. The warranty does not cover
replacement of the entire product or the
USB mobile phone charger if the mobile
phone used has specifications that does
not comply with the charging current or
specifications for the BRIGHT Home and
the USB charger.
How to make a warranty claim
Warranty claims must be made directly to
the point of purchase with a valid proof of
purchase. If the warranty claim is found
to be valid upon point of inspection, a
replacement product or part will be handed
out or ordered for hand out at a later date.
If there is doubt about the validity of the
warranty claim, the product may be kept
by the seller to consult with importer or
BRIGHT Products AS. BRIGHT Products
AS and our representatives are not liable
for products that are damaged or lost in
transit. If needed, we recommend that you
ship your returned products to point of
purchase via a trackable shipment method.
THERE ARE NO WARRANTIES, WHICH
EXTEND BEYOND THIS DESCRIPTION,
AND EXPRESSLY NO IMPLIED WARRANTY
OR MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE. IN NO
EVENT SHALL BRIGHT PRODUCTS BE
LIABLE FOR SPECIAL, INCIDENTAL,
OR CONSEQUENTIAL DAMAGES OR
ANTICIPATED LOSS OF PROFITS
SUFFERED BY THE PURCHASER. BRIGHT
PRODUCTS AND OUR RESELLERS
HAVE NO LIABILITY FOR ANY DAMAGE
OR DESTRUCTION TO CONSUMER
ELECTRONICS DEVICES OR OTHER
PERSONAL PROPERTY THAT ARE
USED IN CONNECTION WITH THE
PRODUCTS, INCLUDING, BUT NOT
LIMITED TO, LAPTOPS, CELL PHONES,
MP3 PLAYERS, DVD PLAYERS OR
HANDHELD DEVICES, OR ANY LOSS OF
DATA CONTAINED IN THE FOREGOING
DEVICES. NOTWITHSTANDING ANY
DAMAGES THAT YOU MIGHT INCUR FOR
ANY REASON WHATSOEVER (INCLUDING,
BUT NOT LIMITED TO, ALL DAMAGES
REFERRED TO HEREIN AND ALL DIRECT
OR GENERAL DAMAGES IN CONTRACT,
TORT (INCLUDING NEGLIGENCE OR
OTHERWISE), THE ENTIRE LIABILITY OF
BRIGHT PRODUCTS AND ANY OF ITS
SUPPLIERS SHALL BE LIMITED TO THE
AMOUNT ACTUALLY PAID BY YOU FOR
THE PRODUCT. SOME STATES AND/
OR JURISDICTIONS DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATIONS
OR EXCLUSIONS MAY NOT APPLY TO YOU.

From larger cities to remote areas, from Norway to Kenya! At BRIGHT we shape the
future by bringing smarter, cleaner and more sustainable energy solutions to the
world, creating better living conditions for people and societies around the planet.
Read more about us and our products on
www.bright-products.com
SunBell 80 SunTurtle Start+ Move 120
2 YEAR
WARRANTY
DESIGNED
IN NORWAY
Other BRIGHT products