BRIGHTLIGHT BL-LS-4350-RGB User manual

TOP / LIGHT DIRECTION
INSTALLATION GUIDE
Actual product characteristics may vary. Bright Light reserves the right to improve, modify or update the product designs without prior notice.
ENCAPSULATED LED RIBBON | CURVE | RGB
COLOUR CODE LUMENS
RGB BL-LS-4350-RGB
R 45lm/m
G 180lm/m
B 50lm/m
LED WATTS 12W/m
INPUT VOLTS 24V DC constant voltage
OPERATING TEMP. -25°C ~ +60°C
MAX. RUN 10m
DIMENSIONS W10.25 × H17mm
(W12mm for connectors)
CUTTING LENGTH 50mm
MINIMUM BEND
RADIUS
25mm
BEND DIRECTION Horizontal bending
BEAM ANGLE 180°
SOURCE LIFE 50,000 hours
WARRANTY 3 years
INGRESS
PROTECTION
Protection established by use of
IP65 connections
CONTROL Requires 3-channel RGB controller
1. Cut Encapsulated LED Ribbon only at
the cut lines shown on Side A of product.
Be conservative to avoid over cutting.
See No. 5 for shortening ribbon.
2. To t a connector: Cut out a notch
(approx 3 × 3mm) from Side A to expose
the underside PCB solder pads. Take
care not to cut or damage the PCB and
LEDs.
SIDE A
Cut mark are visible as darker lines on this side
When connecting cable, notch out from this side
to expose solder pads
INSIDE VIEW - EXPOSE SOLDER PADS
50
SIDE A VIEW - CUT MARKS CROSS SECTION
1
2
3. Cut and trim the cable to the appropriate length and feed
through connector. Solder the wires onto the solder pads of
the Encapsulated LED Ribbon PCB ensuring the correct +,
R,G, B polarity
4. Insert silicone into connector before tting over connection.
The silicone is required to complete the IP65 rating. Failure to
do this will result in warranty becoming void.
5. Shortening ribbon / tting new end cap: Cut Encapsulated
LED Ribbon to length then t end cap and silicone in place.
SAFETY NOTES
– Before making any cuts, installation,
maintenance, or connection, be sure
the mains power is disconnected.
– All connector joints must be connected
correctly to achieve connector IP rating.
– Check the polarity of the connector
before inserting the front connector and
switching on the mains power.
– Cut and connect Encapsulated
LED Ribbon correctly. Any incorrect
operation can cause damage.
– Use a certied Bright Light 24V DC
power supply.
ENCAPSULATED LED RIBBON | CURVE CAN BE CURVED AS SHOWN BELOW:
CUT OUT NOTCH TO EXPOSE
SOLDER PADS
TOP VIEW - EXPOSE SOLDER PADS
2A
CUT OUT NOTCH
TO EXPOSE
SOLDER PADS
DO NOT TWIST THE LIGHT
OR BEND AGAINST THE
LIGHT SURFACE
0800 952 000 | www.brightlight.co.nz | BRIGHTLIGHT
CUTTING RIBBON & CONNECTING BOOT CONNECTORS
ADD SILICONE INTO
CONNECTOR BOOT
BEFORE FITTING
ENSURE THE
CORRECT +, R,G, B
POLARITY
SOLDER WIRES SILICONE CONNECTOR
3
CUT MARK
OFFCUT SIDECONSERVATIVE CUT
4
17
10.25
BRIGHT LIGHT RECOMMENDS CONNECTIONS ARE MADE IN-HOUSE
LIGHT DIRECTION
HORIZONTAL BENDING
MINIMUM BEND RADIUS
25MM

INSTALLATION GUIDE
Actual product characteristics may vary. Bright Light reserves the right to improve, modify or update the product designs without prior notice.
11
14
30
15
WIRING DIAGRAM
– This product requires an RGB controller, it uses a common
positive and all colours are controlled by PWM on the
negative side.
– To minimise voltage drop and ensure consistent light output,
position the power supply near to the power feed end of the
LED Ribbon, and keep the line as short as possible
– Ensure your maximum run adheres to the guidelines; 10m.
– Ensure to add 20% buffer when selecting a power supply green wire: “G” terminal (-)
blue wire: “B” terminal (-)
yellow wire: +
red wire: “R” terminal (-)
POWER SUPPLY RGB CONTROL
24V DC
END CAPBOTTOM FEED CONNECTORSIDE FEED CONNECTOR
ACCESSORY CODE
MOUNTING CLIP 30MM BL-LS-4359
HOLE DIMENSIONS Ø2.5mm
ACCESSORY CODE
SIDE FEED CONNECTOR IP65 BL-LS-4360
BOTTOM FEED CONNECTOR IP65 BL-LS-4361
END CAP IP65 BL-LS-4362
POWER FEED CABLE (1000MM) BL-LS-4358
Encapsulated LED Ribbon requires the soldering of cable onto
PCB solder pads and the use of silicone connectors to ensure an
IP65 protective seal.
Mounting clips allow for the creation of unique Encapsulated LED Ribbon
shapes and designs. Quantity of mounting clips required depends on length
of product, desired shape and mounting surface angle.
0800 952 000 | www.brightlight.co.nz | BRIGHTLIGHT
MOUNTING CLIPS IP65 CONNECTION ACCESSORIES
19
15
12
19
23
12
6
19
12
18
19