Brink Air for life Reference guide

Wireless Controller with humidity sensor
English
Installation regulations

Contents
1 User manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Descripon Wireless Controller with humidity sensor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Delivery content. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2 Technical specicaon. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.1 General product specicaon. . . . . . . . . . . . . . . . . . 6
2.2 Environment inuences. . . . . . . . . . . . . . . . . . . . . . . 6
2.3 Overview operaonal controls. . . . . . . . . . . . . . . . . 7
3 Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1 Mounng Wireless Controller with humidity sensor
on the wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2 Remove Wireless Controller with humidity sensor
from wall bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.3 Connecng the AC/DC converter (opon). . . . . . . 10
3.4 Using another frame (opon). . . . . . . . . . . . . . . . . 12
4 Put into use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
4.1 Connecng with USB Tranceiver (Pairing). . . . . . . 13
4.2 Back to factory seng Wireless Controller with
humidity sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5 Informaon addional Wireless Controller with humidity
sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.1 Connecng addional RF sensor with USB Tranceiver
(Pairing). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5.2 RH-sensor general. . . . . . . . . . . . . . . . . . . . . . . . . . . 17
5.3 Sengs RH-sensor. . . . . . . . . . . . . . . . . . . . . . . . . . 17
6 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
6.1 General maintenance. . . . . . . . . . . . . . . . . . . . . . . . 19
6.2 Replace baery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7 Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
8 Troubleshoong and guarantee. . . . . . . . . . . . . . . . . . . . 21
8.1 Guarantee. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
9 Conformity declaraon. . . . . . . . . . . . . . . . . . . . . . . . . . . 22

1 User manual
Dear client,
Thank you for buying the Wireless Controller with humidity sensor. This user’s manual contains all required
information to quickly become familiar with the product. We kindly request you to carefully go through this
information before using the product. This user’s manual is intended for the Wireless Controller with humidity
sensor installer and end user.
Take good care of this user’s manual! For more information or ordering manuals, please contact:
Brink Climate Systems B.V.
P.O. Box 11
NL-7950 AA, Staphorst, The Netherlands
T: [phone]
F. [phone]
E. [e-mail]
www.brinkclimatesystems.nl
1.1 Description Wireless Controller with humidity sensor
Intended and unintended use
This manual is about the Wireless Controller with humidity sensor (See C in image below).
The Wireless Controller with humidity sensor should only be used in combination with products that have been
approved by Brink Climate Systems B.V.
The Wireless Controller with humidity sensor can only be used with a HRU appliance which is equipped with a
USB connection! The Wireless Controller with humidity sensor is a wireless remote control to operate your
ventilation system. This remote control also displays when the filter(s) needs to be replaced/ cleaned or when the
ventilation system is malfunctioning. Brink supplies a range of wireless remote controls/sensors that make
contact with a heat recovery unit by means of a USB transceiver. This range consists of the 5 following types of
wireless controls/ sensors:
A.
Wireless Controller A.
B. Wireless Controller with B.
build in CO
2
-sensor
C. Wireless Controller with C.
build in RH (humidity) -
sensor
D. Wireless CO
2
- sensor D.
E. Wireless Humidity - sensor E.
F. USB transceiver F.
G. Appliance with USB G.
connection (for example
HRU appliance type Flair)
Wireless Controller with humidity sensor 616880-B Brink / 3

The connected ventilation unit is operated by pressing one of the buttons on the Wireless Controller with humidity
sensor with your finger.
For explanation of the buttons of the Wireless Controller with humidity sensor see ®Overview operational
controls page 7.
The Wireless Controller with humidity sensor must always be used with a transceiver on the HRU appliance; a
combination of multiple remote controllers on 1 USB transceiver is possible.
In total, a maximum combination of 12 controllers /sensors can be connected to 1 transceiver (Max. 4
controllers / max. 4 CO2-sensors and max 4 humidity sensors).
Note: A controller with a build in CO2- sensor is seen as an CO2-sensor and a controller with a build-in humidity
sensor will be seen as an humidity sensor.
When one or more sensors are connected to the HRU appliance, it will ventilate according to the set conditions of
the connected sensor(s).
If multiple controllers /sensors are used, the controller / sensor that requests the highest ventilation level always
has priority.
Boost function ( ):
The boost function can be canceled at any time by pressing another button of the Wireless Controller with
humidity sensor. When the boost button is pressed again during use of the boost function, the timer is reset and
the connected ventilation device will run on ventilation level 3 again for 30 minutes. For position "Boost button"
see ®Overview operational controls page 7.
The air flowquantities associated with the ventilation settings must always be set on the connected appliance
and cannot be adjusted on the Wireless Controller with humidity sensor. For ventilation settings, see the
installation manual of the relevant connected HRU appliance.
Wireless Controller with humidity sensor 616880-B

1.2 Delivery content
Check that delivered Wireless Controller with humidity sensor is complete and not damaged.
The scope of delivery includes 2 boxes; one for the Wireless Controller with humidity sensor with frame and wall
bracket and one for the USB transceiver.
The delivery content of the Wireless Controller with humidity sensor consists of the following components:
1. Wireless Controller with1.
humidity sensor
2. Frame2.
3. Wall bracket3.
4. Double-sided adhesive tape4.
5. Mounting screws5.
6. USB transceiver6.
7. Short information with QR-7.
code to on line manual
Wireless Controller with humidity sensor 616880-B Brink / 5

2 Technical specification
2.1 General product specification
Product description
Name: Wireless Controller with humidity sensor
Technical product specifications
Operating voltage: 3 V
Protection class: IP21
Type of battery :
CR2032.MRF Lithium (preferred manufacturer
Renata or Panasonic CR-2032/BS )
Not applicable if a permanent power connection
is used!
Frequency 868 MHz
Ambient conditions
Ambient temperature: 0 °C to 50 °C
Storage temperature: -20 °C to 60 °C
Humidity: 0% to 90%
Other: For indoor use
Max distance between USB transceiver and
Wireless Controller with humidity sensor 300 m (open field; 1 meter height)
2.2 Environment influences
The Wireless Controller with humidity sensor should be placed and used in a space with the correct ambient
conditions for proper operation. The Wireless Controller with humidity sensor may only be mounted indoors, but
not close to a heat source, a radiator, in a extreme humid environment. The Wireless Controller with humidity
sensor may also not be exposed to direct radiation heat (sun light). The Wireless Controller with humidity sensor
may also not be mounted close to a magnetic field. This could damage internal components.
Wireless Controller with humidity sensor 616880-B

2.3 Overview operational controls
The Wireless Controller with humidity sensor has four (capacitive) buttons (two visible and two invisible buttons).
Each button is equipped with a LED.
1. Button 1 - Automatic ventilation position in 1.
accordance with build in humidity sensor
2. Button 2 - boost function 2.
3. Button 3 - Not visible but available for "note ID" 3.
4. Button 4 - Not visible but available for "note ID" 4.
5. Filter/fault indication LED 5.
Button 1 (auto)
When button 1 is operated, the HRU appliance will be set to ventilation level
1 or the HRU appliance will be ventilate automatically conform set
requirements of the build in humidity sensor; the white LED next to button 1
will flash once as "button press" confirmation.
Button 2 ( )
When button 2 is operated, the HRU appliance will run for 30 minutes at
ventilation level 3 (boost function) and then again at ventilation position 1;
the white LED placed next to button 2 will flash once as "button press"
confirmation.
Button 3 & 4
When the (not visible) buttons 3 & 4 are operated for a note ID (see ®
Connecting with USB Tranceiver (Pairing) page 13 ) the white LED placed
next to these buttons will flash once as "button press" confirmation.
Filter/ fault LED
This LED indicates when filter (s) must be cleaned / replaced or when a
malfunction has occurred in the connected HRU appliance.
Wireless Controller with humidity sensor 616880-B Brink / 7

Filter notification
The filter(s) in the HRU appliance, connected to the Wireless Controller with
humidity sensor, should be cleaned or replaced when the red LED on the
Wireless Controller with humidity sensor appears.
This LED is on for 10 seconds every 3 hours or for 300 seconds if any of the
buttons are operated (Wireless Controller with humidity sensor with battery
power supply).
When the Wireless Controller with humidity sensor is equipped with a
permanent power supply (optional) this LED is permanently on.
Resetting of the filter notification is not possible with the Wireless Controller
with humidity sensor!
Consult the manual of the device connected to the Wireless Controller with
humidity sensor for resetting filter notification
1 = LED Filter nocaon
Fault notification
If there is a fault in the HRU appliance, connected to the Wireless Controller
with humidity sensor, the red LED on the Wireless Controller with humidity
sensor flashes with frequency of 1 Hz (1 blink per second).
This LED flashes for 10 seconds every 3 hours or for 300 seconds if any of
the buttons are operated (Wireless Controller with humidity sensor with
battery power supply).
When the Wireless Controller with humidity sensor is equipped with a
permanent power supply (optional) this LED flashes permanently.
See the installation instructions of the device connected to the Wireless
Controller with humidity sensor for troubleshooting for the error
notifications indicated on the Wireless Controller with humidity sensor.
1 = LED fault indicaon (ashes 1Hz)
Lost connection
When the Wireless Controller with humidity sensor lost connection with the
USB-transceiver the fault LED will also flash.
The LED flashes 3 times 0,5 seconds ON and 60 seconds OFF or flashes for
300 seconds if any of the buttons are operated (Wireless Controller with
humidity sensor with battery power supply).
Filter and fault notifications are overruled. 1 = LED (ash 0.5 sec on - 60 sec o )
Wireless Controller with humidity sensor 616880-B

3 Assembly
3.1 Mounting Wireless Controller with humidity sensor on the wall
You should perform the step1 to step 4 to assemble the Wireless Controller with humidity sensor.
An example of a wireless controller is shown in this section, but other wireless controllers/sensors are
assembled in the same way.
Step 1
The wall bracket can be attached to a flush mount electrical box (Ø 55 mm) or can be directly mounted on
the wall with supplied double sided adhesive tape. Mounting on a electrical box is only necessary when a
permanent power supply (option) is used. The Wireless Controller with humidity sensor should be placed at a
height of approximately 1.65 meters above the floor.
▪Screw or glue the wall bracket onto the wall in the▪
correct position.
Take note!
The up arrow on the wall bracket must point
upwards!
Backside wall bracket with posion
double sided adhesive tape
Step 2
Remove the plastic isolation strip from the battery.
Step 3
Click the Wireless Controller with humidity sensor (A)
together with supplied frame (B) on the wall bracket
(C).
After mounting the Wireless Controller with humidity
sensor on the wall bracket remove the foil from the
front.
Wireless Controller with humidity sensor 616880-B Brink / 9

Step 4
When the Wireless Controller with humidity sensor has been fitted on
the wall the USB transceiver can be placed in the USB port of the
appliance which must be connected with the Wireless Controller with
humidity sensor. To connect the USB transceiver with HRU appliance
see ®Connecting with USB Tranceiver (Pairing) page 13,
Connecting additional RF sensor with USB Tranceiver (Pairing) page
16 .
3.2 Remove Wireless Controller with humidity sensor from wall bracket
For removing the Wireless Controller with humidity sensor from the
wall bracket grasp the front of the Wireless Controller with humidity
sensor by edges and gently pull away from wall.
An example of a wireless controller is shown in this section, but other
wireless controllers/sensors can be removed from the wall bracket in
the same way.
3.3 Connecting the AC/DC converter (option)
Warning!
At all times disconnect the 230 V. power supply when connecting the AC/DC converter.
When using the optional AC/DC converter, the wall bracket must be attached to a electrical wall box (Ø 55 mm).
Connect the optional AC/DC converter (A) with the Wireless Controller with humidity sensor (B) conform the wiring
diagram.
The following actions should be performed to connect the optional 5V AC/DC converter:
Step 1
▪Place the converter in the wall box.▪
▪The 230V power supply must be connected to the factory▪
mounted gray connectors. Strip the wire over a length of
approx. 7 mm.
Step 2
▪Screw the wall bracket on the wall box and feed the red▪
and black wires including mounted green connector
through the square hole in the in the mounting plate.
▪Take note!▪
The up arrow on the wall bracket must point upwards!
Step 3
▪After feed the red and black wire with the green▪
connector through the frame connect this to the
connector on the back side of the Wireless Controller
with humidity sensor.
▪Removal of the battery is not required but recommended.▪
A.
AC/DC converter (230V~/5V=) A.
B. Wireless Controller with humidity B.
sensor
X1 = Black
X2 = Red
X3 = Brown
X4 = Blue
Wireless Controller with humidity sensor 616880-B