Brinno PHV 133014 User manual

PHV 133012/ PHV 133014
The Digital Door Viewer!
User Manual

Thank you for purchasing Brinno’s PeepHole Viewer!
If you have any questions or problems setting up your Brinno
PeepHole Viewer, please contact the sales sta where you
purchased our product or email Brinno Incorporated directly at
[e-mail]
Please Visit our website
www.brinno.com
1
www.brinno.com
Thank you for purchasing Brinno PeepHole Viewer!
PHV1330 features
Brinno PeepHole Viewer uses an LCD panel to display who is at your
door. it turns a hard to see door viewer image into a big and birght
image.
• 3" LCD panel to show visitor's image
• Use MicroSD card to store images
• 2 AA batteries for 1300 "peeps"
• Brightness Enhancement
• With Motion Sensor* can record visitor's image automatically
when visitor come close to your front door
• With Knocking Sensor* can record visitor's image automatically
when visitor knocking on your door
* Motion Sensor and Knocking Sensor are optional accessories!
Image Recording Brightness Enhancement Big Bright LCD Motion Sensor* Knocking Sensor*
3.0”

FOR BEST RESULTS PLEASE USE THE PEEPHOLE LENS INCLUDED.
1. PeepHole Viewer
2. Base Flange
3. Washer
4. PeepHole Lens
5. PeepHole Barrel
6. Tightening Tool
7. 2 AA Batteries
2
1
2 3
Package Contents

1. Locking Screw
2. Micro SD card slot
3. Low Battery Indicator
4. Power Button
5. Brightness Enhancement
6. Up button/ Time Setting
7. Down button/ Playback
8. Battery Cover
3
www.brinno.com
Device Parts
5
6
7
2
3
4
8
1

4
Display Icons
SD
SD
FULL
3
4
5
1
6
2
When this icon is displayed on screen, backup the images to your
PC or notebook, otherwise the oldest folder will be erased!
1. Micro SD card scanning in progress
2. Brightness Enhancement mode
3. Image recording
4. No Micro SD card
5. Micro SD card full
6. Playback mode

5
www.brinno.com
IF THE LOW BATTERY INDICATOR FLASHES, PLEASE REPLACE THE
BATTERIES.
1. Open battery cover
2. Install 2 AA batteries
12
Install BatteriesInitial Setup

6
Date & Time
Set
2011/ 3/31
12:30:55
Exit
Date & Time
: OK to next
+
-
2011/ 3/31
12:30:55
Date & Time
: Done
+
-
2011/ 3/31
12:30:55
OK
2
345
1
+
-
1. Press to turn on the PeepHole Viewer.
2. Press and hold for 3 seconds.
3. Select "Set" to enter setting mode.
4. Set the date and time.
5. Select “Done”.
Set Date and TimeInitial Setup

7
www.brinno.com
Installation

8
Insert the PeepHole lens to pass through
the outer side of the door.
1
For 14mm peephole
Insert the PeepHole barrel through the
Base Flange and insert both into the hole
on the inner side of the door.
Tighten the PeepHole Barrel with your
fingers.
-A
2
For 12mm peephole
Insert the PeepHole barrel through the
Washer and Base Flange and insert both
into the hole on the inner side of the
door.
Tighten the PeepHole Barrel with your
ngers.
2
-B
When the barrel is snug, rotate the Base
Flange until the TOP icon is at 12 o’clock
(vertical).
3

9
www.brinno.com
Use the Tightening Tool included to
tighten the PeepHole barrel.
4
Hold the PeepHole Viewer at a -25 degree
counter-clockwise position and insert it
onto the Base Flange.
5
Rotate the PeepHole Viewer clockwise
until it locks into place.
6
Use the screwdriver to tighten the
Locking Screw.
You are now ready to turn the PeepHole
Viewer on.
7