Erasing Information For All Paired Phones
Switch BH-200 on while your Bluetooth phone is off. BH-200’s status should be
Connectable (LED flashes blue every 5 seconds). Press and hold the Volume Up Button
for 5 seconds. When the headset beeps, release the button. The beep confirms that
pairing information for all phones has been erased.
Disconnecting Headset From A Phone
The headset can be disconnected from your phone by:
Using the Power Button to switch off BH-200.
Disconnecting BH-200 in the Bluetooth menu of your phone.
Moving BH-200 more than 30’ away from your phone.
Note: You do not need to delete the pairing to disconnect the headset from your phone.
Reconnecting Headset To A Paired Phone
Switch on BH-200 within 30’ of your (last connected) phone and it will connect auto-
matically. Your phone must also be switched on and its Bluetooth function enabled.
If BH-200 does not connect automatically, check to make sure the headset and phone
are paired.
If BH-200 is moved more than 30’ from the phone, the headset is out of range and
will disconnect from the phone. A warning beep is provided when the headset moves
out of range of the phone. If BH-200 moves back into range within 10 minutes, it will
automatically reconnect.
When BH-200 is out of range for more than 10 minutes, its status changes to Connect-
able (LED flashes blue every 5 seconds). The BH-200 will not automatically connect to
the phone when its status is Connectable, even if moved within 30’ of the phone. To
reconnect, simply switch the headset off, then switch back on. You can also reconnect
by using the phone’s Bluetooth menu.
If BH-200 is switched on within 30’ of two or more paired phones, it will attempt
to connect with the last connected phone. If a connection is not made with the last
connected phone within 20 seconds, BH-200 remains Connectable.
Calling Features
Making A Call – With BH-200 connected to your phone, enter a telephone number
and place the call using your phone in the normal manner.
If your phone supports last number redialing with the headset, press and hold the
Volume Up Button for 2 seconds. If your phone supports voice dialing with the
headset, press and hold the Volume Down Button for about 2 seconds, or until you
hear a tone prompting you to start the voice tag. Your phone should then play the
voice tag and dial the requested phone number. To activate either feature, a call may
not be in progress.
■
■
■
Answering / Ending A Call – When receiving a call, the ring tone is heard through
the headset speaker. To answer a call, briefly press the Power / Call Button on BH-200
or the answer key on your phone. If you do not want to answer the call, press the
Power / Call Button two times. To end a call, briefly press the Power / Call Button on
BH-200 or the end key on your phone.
Adjusting The Headset Speaker Volume – Press the Volume Up Button to increase
audio level or the Volume Down Button to decrease audio level.
Switching A Call Between Headset / Phone – During the call, press the Power /
Call Button and Volume Down Button simultaneously for 2 seconds, or use the respec-
tive function in your phone.
Switching Between A Current / Waiting Call – To switch from your current call in
progress to a waiting call, press and hold the Volume Up Button for about 2 seconds,
or use the respective function in your phone.
Muting The Microphone – To mute or unmute the microphone during a call, press
and hold the Power / Call Button and Volume Up Button simultaneously for 2 seconds.
A beep is provided every 5 seconds to advise that the microphone has been muted.
Adjusting For Use On Either Ear
The BH-200 may be used with or without the earhook, based on your preference. If
you choose to use BH-200 without the earhook, simply position the headset speaker
in your left or right ear. Whether placed in your left or right ear, the microphone end
should be angled toward your mouth.
To use BH-200 with the earhook, it must first be attached to the headset. The earhook
snaps in place on the headset below the speaker. To remove the earhook, hold it near
the headset and pull gently.
If you want to use the earhook and wear the head-
set on your right ear, attach the earhook as shown
in the illustration marked R.
If you want to use the earhook and wear the head-
set on your left ear, attach the earhook as shown in
the illustration marked L.
The earhook is flexible and can be adjusted to fit
tightly of loosely around your ear, while holding the
headset securely against your ear.
Troubleshooting
If the headset is not functioning, it may be necessary to reset BH-200. To reset the
headset, press and hold the Volume Up Button and connect the QTC-BH200 charger
to the headset. Once the QTC-BH200 is connected, continue to hold the Volume Up
Button for 2 seconds to complete the reset.
If you cannot connect BH-200 to your phone, make sure the headset is charged, switched
on, and paired to a Bluetooth enabled phone. Also, ensure that the Bluetooth feature is
activated on your phone, that the headset and phone are in close proximity (maximum 30
feet without obstruction), and that there is no interference from other electronic devices.
Headset Care
Use and store the BRIO BH-200 at room temperature and in dust / dirt free environ-
ments. Keep headset dry and away from moisture and humidity. Do not drop, shake, or
handle headset in a rough manner. Clean only with a damp cloth and mild detergent.
Warranty
HT Mobile Products, Inc. (HTMP) warrants this product to be free from defects in
workmanship and materials for 12 months from date of retail purchase. This warranty
applies to the original purchaser and is void if the product has been altered, misused,
damaged, neglected, purchased outside the United States, or if repair is required
because of normal wear and tear. This is the only warranty made by HTMP. In no
event will HTMP, its affiliates, subsidiaries, related entities, or their respective direc-
tors, officers, or employees, be liable for any damages beyond repair or replacement
as described above, including without limitation, indirect, incidental, or consequential
damages. For service under warranty, return the product along with dated proof
of purchase to the retailer where purchased or to HT Mobile Products. If returning
directly to HT Mobile Products, follow these instructions:
Send to HT Mobile Products – Warranty Service Department, 2170 Brandon Trail,
Alpharetta, GA 30004. For your protection, we recommend you obtain proof of
delivery for your shipment.
Include with your product, dated proof of purchase, your name and daytime tele-
phone number, and return address (street address only; return shipments cannot be
made to a P.O. Box).
All items sent become the property of HT Mobile Products and will not be returned.
BRIO BH-200 is compliant with Bluetooth specification 2.0 and supports hands-free profile 1.5 and
headset profile 1.1.
©2007 HT Mobile Products, Inc. BRIO is a trademark of HT Mobile Products, Inc. All rights reserved.
Printed in China.
1.
2.
3.
