Bristan GWF BF C Wiring diagram

Connect the hot and cold water supplies
to the threaded tails using ¾” BSP
connector (not supplied). Turn on the
mains water supply letting the water flow
for a few minutes to flush through the
system. Check all joints and connections
for any leaks.
43
12
Pack Contents
Installation Instructions
& User Guide
1.0
5.0
Pressure
BAR
0.2
4.0
2.0 3.0
Pressure
BAR
1.0
5.0
0.2
4.0
2.0 3.0
60°C
65°C
Max
80°C
Specifications
Maximum Static Pressure: 10.0bar
Inlet water temperature
3/4” Male BSP
Tap Connector
Inlet Dimensions
Inlet Connection
Min: 0.3bar Max: 5.0bar
Dynamic Water Pressure
5°C
25°C
Cold Water Supply
Min: 5°C Max: 25°C
Hot Water Supply
Tools you’ll need
x2
x2
x2
x1
All products manufactured and supplied by Bristan are safe
provided they are installed, used correctly and receive regular
maintenance in accordance with this instruction.
This product needs to be installed in accordance with, and meet the
requirements of the Water Supply (Water Fittings) Regulations 1999
and Scottish Bye-laws 2004.
For product specific installation requirements, please visit
www.wras.co.uk
Isolation valves must be fitted to the inlet water supplies to ensure
ease of future maintenance.
Before installing this product the water supply must be thoroughly
flushed in order to remove any swarf, solder etc.
This product must not be modified in any way as this will invalidate the
guarantee.
Full access must be made available for future maintenance /
servicing purposes.
If in doubt, contact a registered plumber or your Local Water Authority
or the Secretary of the Institute of Plumbing, address as follows;-
The Institute of Plumbing,
64 Station Lane,
Hornchurch,
Essex,
RM12 6NB, Tel: [phone]
Prior to Installation
Adjustable
spanner Pipe cutter Hexagonal Key
Installation
60-65°C
Recommended
80°C
Maximum
Please leave these instructions
with the end user
Product code: GWF BF C (D1)
Place the plinths
over the holes
in the bath
ensuring that
the washers are
fitted between
the plinths and
the bath.
Secure the body to the bath by using
the washer and metal back nut below
the bath. Tighten the back nut onto
the threaded tails.
Fit the body to
the bath.
Why not visit our
YouTube channel
To see our latest how-to videos,
simply scan the QR code with your
smart phone or tablet.
Alternatively visit www.youtube.com/bristantv
180mm
Cold
Hot
Operation
Cold
On
On
Hot

At Bristan, we want to make things as easy as possible for our customers.
That’s why we oer solid guarantees on all our products,
eective from the date of purchase, to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product,
alternatively visit www.bristan.com/register.
For any other queries, please call our Customer Service on 03300266273
where our expert team of advisors will be able to oer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/guarantees.
Troubleshooting
Notes
Symptom Cause Remedy
No flow or
low flow
rate
Partially closed isolation valve. Open isolation valve.
Instantaneous water heater cycles on
and o as flow rate or pressure is too
low.
Increase water flow rate or pressure through system.
Head of water is below the
minimum distance required.
2 meters minimum required.
Hot or cold water being drawn o
elsewhere causing pressure changes or
instantaneous boiler temperature
changes.
Do not use other water outlets when using the taps.
Air lock or partial blockage in the supply
pipe work.
Flush through pipe work to ensure removal of debris
and any air locks.
Water
dripping
from taps
This is normal for a short time after using
the taps.
This is caused by capillary action, the build up of
water in the tap body.
If water continues to drip,
possibly due to the ceramic disc valves
Remove valves and clean, refer to 'Maintenance'
section before starting any maintenance.
Taps do not
turn on
Closed isolation valve. Open isolation valve.
Mains water supply turned o. Turn on mains water supply.
3
2
1
Maintenance - Valve Cleaning
Replace the valve into
the body and tighten in
a position. Replace the
handle, tighten the grub
screw and push fit the
cap.
Please use this space for any notes you or your installer may have regarding the installation of this product.
Remove the cap and
loosen the grub screw.
Remove the handle.
Remove any O-rings, soak the
valve in de-scaler and wash
o in clean water. Examine all
seals and replace if needed. Use
WRAS approved silicon based
grease on all seals.
2.5
mm
2.5
mm
Your fitting has a high quality finish and should be treated with
care to preserve the visible surfaces.
All surfaces will wear if not cleaned correctly, the only safe way
to clean your mixer tap is to wipe with a soft damp cloth. Stains
can be removed using washing up liquid. All bath cleaning
powders and liquids will damage the surface of your fitting, even
the non-scratch cleaners.
Note: Never use abrasive detergents or disinfectants or those
containing alcohol, hydrochloric acid or phosphoric acid.
General Cleaning Spare Parts
To replace any spare parts for your
bath shower mixer why not scan
the QR code and search for your
product
2.5
mm