Bristan Artisan Evo Mounting instructions

Installation Instructions
and User Guide
Artisan Evo
Digital Electronic Mixer
Shower
Models covered: ARDE SHCCF W &
ARDE SHCCF B
Please keep this booklet for future
reference.
Installer, when you have read these
instructions please ensure you leave
them with the user.
E

Contents
2 Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
Welcome to your new Bristan Digital Electronic Mixer Shower, featuring a contemporary
design, wireless electronic controller and digital mixing unit.
Bristan’s Digital Electronic Mixer Shower has been designed to be easy to install and
use. It has also been designed and tested in the UK to all of the relevant British
Standards.
These instructions are for your guidance to a safe and successful installation, so please
read them thoroughly and retain for future reference.
We recommend the installation is carried out by a suitably qualified person and must
conform with current I.E.E Wiring Regulations (BS7671) and Building Regulations (Part
P and Part G).
Important Safety Information …………………………………………………..…………..
General Information ……………………………………………………………………………..
Pack Contents ……………………………………………………………………………..……….
Tools Required …………………………………………………………………………….………..
Product Features ………………………………………………………………………………….
Specifications ……………………………………………………………………………………….
Dimensions ………………………………………………………………………………….……….
Installation Requirements …………………………………………………………..……….
Positioning the Mixer Valve …………………………………………..……..
Water Requirements …………………………………………………………….
Electrical Requirements ………………………………………………..…….
Installation …………………………………………………………………………………..……….
Fitting the Mixer Valve …………………………………………………..……..
Water Connections …………………………………………………..……........
Electrical Connections ………………………………………………………….
Fitting the Wireless Controller .……………………………………….……
Shower Arm & Rose..……………………………………………………….……
Commissioning ……………………………………………………………………………………..
Wireless Initialisation & Pairing …………………………………….…….
Maximum Temperature Setting ……………………………………..…….
Water / Plumbing Connections …………………………………………….
Purge Procedure …………………………………………….......................
Basic Functional Testing ………………………………………………..…….
Operating the Shower ………………………………………………………………….……….
Maintenance ………………………………………………………………………………..……….
Troubleshooting …………………………………………………………………………..……….
Spare Parts ………………………………………………………………………………….……….
Notes ………………………………………………………………………………….………...........
Guarantee ……………………………………………………………………………………………..
3
4
5
5
6
7
8
9-11
9
10
11
12-17
12
13
14
15
16-17
18-20
18-19
19
20
20
20
21
22-24
25-26
27
28-29
30-31

• Please read these instructions thoroughly and retain for future use.
• All products manufactured and supplied by Bristan are safe provided they are
installed, used correctly and receive regular maintenance in accordance with these
instructions.
• If you are in any doubt about your ability to install this product safely you must
employ the services of an experienced qualified plumber / electrically qualified
person.
• This Digital Electronic Mixer Shower needs to be installed in accordance with, and
meet the requirements of the Water Supply (Water Fittings) Regulations 1999 and
Scottish Byelaws 2004.
• Before starting any installation please consider the following:
• Before drilling into walls, check that there are no hidden electrical wires, cables or
water supply pipes. This can be checked with the aid of an electronic detector.
• If power tools are used do not forget to: - Wear eye protection
- Unplug equipment after use
• Warning: Before installing the new Digital Electronic Mixer Shower it is essential
that you thoroughly flush through the pipework in order to remove any remaining swarf,
solder, etc. Failure to carry out this procedure could cause problems or damage to the
workings of the Mixing Valve.
• Do not operate the shower if the water stops flowing during use or if the water is
leaking from the Mixing Valve itself. Turn off at the mains electrical supply and refer to
the Troubleshooting section (see pages 26-27) or contact Bristan Customer Services on
0844 701 6273.
• Do not block the flow of water from the shower rose by smothering it on your hand or
any other part of your body or foreign object.
• Warning: Do not operate this product if you suspect it is frozen. Do not site the
Mixing Valve where it might be subjected to freezing conditions.
Important Safety Information
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers. 3
BEAB (British Electrotechnical
Approvals Board) approval
of safety.
0359
Hereby, Bristan Group Ltd, declares that this Electronic Mixing Valve with
Wireless Controller is in compliance with the essential requirements and
other relevant provisions of the Directive 1999/5/EC. The declaration of
conformity may be consulted at www.bristan.com/dop.

General Information
4 Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
Recommended Usage
Domestic Heavy
Commercial
Light
Commercial Health Care
• Remove all packaging and check the contents for damage before starting any
installation.
• Fitting isolation valves to the inlet feeds is required as close as is practical to the
inlet connections for ease of maintenance.
• Always switch off the power at the consumer unit and isolate the electrical supply
before making any electrical connections or if you have to remove the cover of the
Mixing Valve.
• This product must not be modified in any way as this will invalidate the guarantee.

Pack Contents & Tools Required
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers. 5
Wireless Controller x1
Mixing Valve Screw x4
Remote Control Screw x3
Wall Plugs x7
Arm x1
Shroud x1
Sealing
Washer x1
Rose x1
Mixing Valve x1
Drill Suitable Drill bit Phillips Screwdriver
Flat Head Screw
Driver Electrical Screwdriver
Masking TapeElectrical PliersElectrical TesterPencilSpanner
Tools Required - Not supplied
Batteries x2

1. Temperature control
Press to increase the temperature up
to a factory set maximum of 48ºC (the
maximum temperature can be overridden,
see Maximum Temperature Setting on
page 19).
Press to decrease the temperature
down to a minimum of 35ºC.
2. Lever handle
Turns the shower on and adjusts the
flow of water. Turn anti-clockwise to turn
the shower on and back to to turn the
shower off.
3. Water flow settings
The shower has 4 flow settings.
Eco ( ), Low ( ), Medium ( ), and
High( ).
4. Digital display screen
Displays the water temperature . Any
error codes will be displayed on here.
5. Time out setting
If the shower valve has been running for
30 minutes the Mixing Valve will
automatically shut off to save water and
energy.
Normal use will be resumed once the
lever handle has been returned to the ‘Off’
position.
E
Product Features
1
2
4
3
E
6 Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Specifications
Water Supply Requirements
Inlet connections: 1/2” BSP with 70mm between centres.
Operating pressure range: Min. 0.5 bar - Max. 5.0 bar
For optimum performance a minimum dynamic working pressure of 1.0 bar is required.
Minimum static pressure: 0.5 bar
Maximum static pressure: 10.0 bar
Supply requirements:
Minimum cold water supply temperature: 5ºC.
Maximum cold water supply temperature: 20ºC.
Minimum hot water supply temperature: 52ºC.
Maximum hot water supply temperature: 65ºC.
Flow Performance
Flow Setting Optimum Flow Rate (lpm)
6 lpm
8 lpm
10 lpm
12 lpm
Electrical Supply Requirements
Supply voltage: 230V AC / 35W
E
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers. 7

Dimensions (mm)
8 Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
86
123
E
212
226
70
200
223
60
G1/2
200
145 165
55
40
45

Installation Requirements
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers. 9
Positioning the mixing valve
The Mixing Valve can be positioned on
either a wall surface or flat on the floor.
(Refer to the diagrams for the correct
orientation of the Mixing Valve).
The Mixing Valve can be installed in either
an airing cupboard, loft space or under the
bath. Do not site the Mixing Valve where it
may be subjected to freezing conditions or
ambient temperatures over 40ºC.
The maximum distance from the Mixing
Valve to the Wireless controller must not
exceed 10 metres as this is beyond the
operating range of the wireless controller.
Wireless installation considerations
As with any wireless / radio product:
- Metallic lined materials or metal
objects (such as steel baths or metal
tanks, etc.) can significantly reduce the
operating range of the wireless interface
or prevent operation.
- Interference from other radio signals
has the potential to affect the ability of the
wireless interface to function correctly.
Note: If the Mixing Valve loses wireless
communication with the controller, the
shower will automatically turn off safely. Vertically up on the wall
DO NOT INSTALL UPSIDE DOWN ON
THE WALL!
Vertically down on the wall
Flat on the floor
DO NOT INSTALL HORIZONTALLY ON
THE WALL!

Installation Requirements
10 Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
Water Requirements
This fitting needs to be installed in
accordance with the following Installation
Requirements and Notes (IRN) to ensure
they meet the requirements of the Water
Supply (Water Fittings) Regulations 1999
and the Scottish Byelaws 2004.
The fitting shall be installed so that its
outlet discharges above the spill-over
level of any appliance as indicated on the
illustration below.
For backflow protection in premises or
installations up to, and including Fluid
Category 3 and 5.
The vertical distance of the outlet above
the spill-over level shall be not less than
20mm or twice the diameter of the inlet
pipe to the fitting, which ever is the
greater. If the fitting cannot be installed
as indicated it shall be installed with a
backflow prevention arrangement suitable
for the Fluid Category.
If the shower is to be installed in a hard
water area, we recommend that an in-line
scale inhibitor is fitted which will prolong
the life of the shower. Please refer to your
supplier for advice.
Warning: the shower must not be
installed in an area subject to freezing
conditions. Do not use if you suspect the
shower is frozen, this will damage the
shower unit.
Maximum ambient temperature: 40ºC.
A minimum working inlet pressure of
0.1MPa (1bar) at a minimum flow rate of
10 litres per minute is recommended for
full performance.
The maximum static inlet pressure must
not exceed 1.0MPa (10bar).
If it is intended to operate the shower
above the recommended operating /
dynamic pressure, a suitable pressure
reducing valve (PRV) should be used.
Water regulations stipulate that a
removable showerhead be constrained by
a fixed or sliding attachment (hose
retainer supplied) so that it can only
discharge water at a point not less that
20mm above the spill-over lever of the
bath or shower tray or other fixed
appliance.
E
Bath spillover
level
Shower tray
spillover level
Ceiling fed
arm & rose
Controller

Installation Requirements
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers. 11
Note: If a showerhead can sit within a
bath, basin or shower tray, Water
Regulations stipulate a double check valve
must be fitted in the supply pipe work to
prevent back siphonage*. If the
showerhead can sit within a WC then the
air gap should be a type AUK3 not less
than 20mm or twice the diameter of the
inlet pipe to the fitting, whichever is the
greater.
* As this shower unit is already supplied
with a single check valve pre-fitted in each
water supply inlet, a further single check
valve would be required in such a
situation, fitted in each water supply as
close as possible to the existing check
valves.
Electrical Requirements
Warning: This appliance MUST be
earthed!
Power Rating: 230V AC / 35W
The Electricical Installation and Curcuit
Protection of this shower must comply
with current I.E.E Wiring Regulations
(BS 7671) and Building Regulations
(Part P). We recommend that this Digital
Electronic Mixing Shower is installed by
a qualified electrician prior to use. The
following notes are for your guidance only.
Important: You must switch off the power
at the consumer unit, isolate the electrical
circuit and verify the earth before making
any electrical connections.
The Mixing Valve must only be connected
to a 230-240 V AC supply.
This product must be connected to a fused
spur with double-pole isolation and a 3A
fuse.
It is recommended that a residual current
device (RCD) formerly known as an earth
leakage circuit breaker (ELCB) with a
tripping current of 30mA, incorporated in
the circuit. This may be part of the existing
consumer unit or a seprate unit.
For close circuit protection DO NOT use
a rewireable fuse. Instead use a suitably
rated miniature circuit breaker (MCB) or
Cartridge Fuse.
Do not turn on the electrical supply until
the plumbing has been completed and the
Mixing Valve cover re-fitted (if removed).

Installation - Mixing Valve
Fixing the Mixing Valve to the floor / wall
Please refer to Positioning the Mixing
Valve on page 9 before starting any
installation.
The Mixing Valve needs to be installed on
either a flat floor or a wall surface.
Position the Mixing Valve on the floor or
wall surface and mark all 4 fixing points.
Warning: Please check for any hidden
pipes and cables before drilling holes into
the floor / wall.
If you are fitting the Mixing Valve to a
partition wall, a wall of particularly friable
(crumbly) substrate or a wooden floor you
will need appropriate fixings for the floor /
wall type.
Drill suitable holes in the floor / wall
surface at the marked positions and insert
wall plugs (if required).
Secure the Mixing Valve to the floor/wall
surface using the fixings supplied or
suitable fixings dependant on floor / wall
type.
Important: Under no circumstances
should the mixing valve be recessed as
this may prevent air circulating and
condensation escaping.
Fixing points
12 Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Installation - Water Connections
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers. 13
Plumbing Connections
Warning: Do not solder within 300mm
of the Mixing Valve or allow solder or flux
to fall onto the casing.
Important: An additional independant stop
valve complying with the current water
regulations must be fitted in the mains
water supply as a means of isolating the
supplys to the Mixing Valve for servicing
and / or maintenance work.
It is essential that all pipe work is flushed
through to remove debris and swarf that
could otherwise damage the unit. Once
the pipework has been flushed through,
turn off the water supplies at the stop /
service valves.
The supplied filter washers supplied must
be fitted into both inlets.
The connecting pipework must present
1/2 BSP connectors to the male thread on
the inlet connections.
Important: The pipework must run
as straight as possible to the Mixing
Valve minimising 90º angled bends as
this could affect the inlet pressure to
the Mixing Valve reducing performance.

Installation - Electrical Connections
Electrical Connections
The electrical installation must be carried
out in accordance with the current I.E.E
Wiring Regulations (BS 7671) and Building
Regulations (Part P).
Warning: This appliance and all
connecting metal pipework must be
earthed via the supply cord, which must
be correctly connected to the earth point
located in the terminal box.
The Mixing Valve must be permanently
connected to the fixed wiring of the mains
supply using the factory fitted supply cord,
via a double pole switched fused spur off
the ring main.
In the interests of electrical safety a
30mA residual current device (R.C.D. not
supplied) should be installed in the supply
circuit. This may be part of a consumer
unit or a separate unit.
Wiring of connection unit:
Warning: This appliance must be
earthed.
The wires in the mains lead are coloured
in accordance with the following code:
Green and Yellow Earth
Blue Neutral
Brown Live
As the colours of the wires in the mains
lead of this appliance may not correspond
with the coloured markings identifying the
terminals in your connection unit proceed
as follows:
• The wire which is coloured green and
yellow must be connected to the
terminal in the connection unit which
is marked with the letter E or by the
earth symbol or coloured green or
green and yellow.
• The wire which is coloured blue must
be connected to the terminal which is
marked with the letter N or coloured
black.
• The wire which is coloured brown
must be connected to the terminal
which is marked with the letter L or
coloured red.
14 Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Installation - Wireless Controller
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers. 15
Fitting the Wireless Controler
Remove the locking ring and wall bracket
from the wireless controller by twisting
the locking ring clockwise.
Position the wall bracket onto the finished
wall surface and mark the fixing holes.
Drill holes at the marked positions on the
wall surface using a suitable drill bit for
the fixings.
Warning: Please check for any
hidden pipes and cables before drilling
holes in the wall.
Tips:
A piece of insulation or masking tape
positioned where holes are to be drilled
and before marking out the exact position
for the fixing holes will help stop the drill
bit from wandering, particularly on a tiled
surface.
When working near a basin, bath or
shower insert plug or cover waste to
prevent losing small parts.
Take care not to drop tools/equipment into
basin, bath or shower during installation.
Secure the wall bracket to the wall using
the fixings supplied or suitable fixings for
the wall type, ensuring the locking ring is
positioned behind the fixing bracket.
Once the wall bracket is secured to the
wall surface turn the locking ring so that
one of the four fixing lugs is at a 12 o’clock
position.
Fit the remote control onto the locking
ring. Twist the locking ring anti-clockwise
to lock the remote control into postition.
Wall
Bracket
Locking Ring
Wall
Bracket
Twist locking
ring anti-
clockwise to
lock.
Fixing Lug

Fitting the Ceiling Fed Arm & Rose
Before proceeding with fitting the ceiling
fed arm and rose, suitable 15mm supply
pipework must be installed above the
ceiling / in the loft area, from the Mixing
Valve to the desired location of the arm.
Important: The pipework must be
rigid / fixed to a joist or beam to ensure it
does not move.
See opposite for examples of pipework
installation.
Either a brass union 1/2” compression x
1/2” M/F or a brass union elbow 1/2”
compression x 1/2” F/M fitting should be
used at the end of the supply pipework to
allow connection of the ceiling fed arm.
Note: When installing the brass union
fitting take into consideration the length of
the thread on the arm and the thickness of
the ceiling / plasterboard.
Pipework secured to the top of a beam /
joist
Pipework secured to the side of a beam /
joist
1/2” BSP
Connection
Pipe Clip
Beam /
Joist
Ceiling /
Plasterboard
Compression Nut
& Olive
Pipe Clip
Push-Fit connection
Pipe Clip
Joist
Ceiling /
Plasterboard
15mm Pipework
15mm
Pipework
16 Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
Installation - Ceiling Fed Arm & Rose

Installation - Ceiling Fed Arm & Rose
Drill a 25-30mm hole in the ceiling /
plasterboard at the required position for
the shower arm.
Screw the shroud onto the top thread of
the arm.
Place the top thread of the arm through
the hole in the ceiling / plasterboard and
secure in place using a G1/2 backnut.
Using a suitable thread sealant connect
the brass union fitting to the thread of the
arm.
Note: The shroud should be flush against
the ceiling / plasterboard to hide the hole.
Screw the shower rose onto the lower
thread of the arm, ensuring the sealing
washer supplied is fitted between the
thread and the rose connection.
Shroud
Arm
1/2”
connection
Sealing
Washer
Celing
Arm
Arm
Sealing
Washer
Rose
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers. 17

Commissioning - Wireless Connection
Wireless Initialisation & Pairing of the
remote control to mixing valve
For the wireless communication to work,
the Remote Control needs to be initialised
and paired with the Mixing Valve. This is
pre-configured upon manufacturing of the
product, so the product should work
“out-of-the-box”.
1. Check the Wireless Communication is
configured correctly.
Ensure the Remote Control is equipped
with the 2 x AA batteries supplied and the
flow lever is in the position (6 o’clock).
Isolate both hot and cold water supplies to
the Mixing Valve and turn the power to the
Mixing Valve off.
1.1. Power on the Mixing Valve. The LED
will initially show “Green”. Wait for ˜30
seconds, the LED will show “Yellow” to
indicate “No wireless connection”.
1.2. Turn the Remote Control “on” by
turning the flow lever to “eco” position
(5 o’clock). The Mixing Valve LED should
return to “Green” in a few seconds to
indicate wireless communication. Turn the
Remote Control “off” by turning the lever
back to and turn the power off to the
Mixing Valve.
If the Mixing Valve LED returns to
“Green”, the product is Initialised and
Paired correctly and no further action
is required.
If the Mixing Valve LED stays “Yellow”,
the Wireless Connection is not
configured correctly. Proceed with the
Initialise (2) and Pairing (3) steps.
E
Additionally, it may also be necessary
to perform the Initialisation and Pairing
(Steps 2 & 3), if:
- You purchase a separate /
replacement unit (either the Mixing
Valve or Remote Control).
- The pre-set address used for the
Pairing is used on a second nearby
Wireless Controller.
IMPORTANT: Both the Initialisation and
Pairing steps must be performed in
sequence.
2. Initialise the Remote Control Wireless
Address.
2.1. Turn the Remote Control “on” by
turning the lever to the “eco” position.
a. If the display shows a flashing 2-digit
number, e.g. “30”. Proceed to step (2.2)
b. If the display shows a single flashing
“0” , press the Temp up button ten
times to increment the flashing
number from “0” to “9”, and then to
a flashing 2-digit number, e.g. “30”.
This has now Initialised the Remote
Control - proceed to Pairing (3).
2.2. Enter Engineering Mode: press and
hold both the Temp up and Temp down
buttons together for more than three
seconds, then release.
Note: If “2” is displayed, press Temp down
button twice to read “0”.
2.3. Press the Temp up or Temp down
button to change the number until “2”
is displayed, The “2” will stay displayed for
˜2 seconds, and then change to a flashing
“0”.
E
18 Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.

Commissioning - Max Temp Setting
Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers. 19
2. Locate the block of four switches
marked SW1 on the circuit board. Position
the individual switches as per the
following diagrams.
Note: Only switches 1-3 need to be
altered.
38ºC
SW1-1 OFF
SW1-2 OFF
SW1-3 OFF
41ºC
SW1-1 ON
SW1-2 OFF
SW1-3 OFF
44ºC
SW1-1 OFF
SW1-2 ON
SW1-3 OFF
46ºC
SW1-1 ON
SW1-2 ON
SW1-3 OFF
48ºC
SW1-1 OFF
SW1-2 OFF
SW1-3 ON
Once the switches have been altered, to
the desired position the maximum
temperature is set.
3. Replace the Mixing Valve cover and
secure with the five fixing screws.
IMPORTANT: It is important to power
down the Mixing Valve to change the
switch settings as they are only read on
power up.
2.4. Press the Temp up button ten
times to increment the flashing number
from “0” to “9”, and then to steady-state
“2” or ‘E1’. This has now Initialised the
remote control.
2.5. Exit Engineering Mode: Press the
Temp down button twice to change the
displayed number back to “0”, and / or
turn the Remote Control “off” by turning
the lever back to .
3. Pairing the Remote Control to the
Mixing Valve.
3.1. Remove the cover from the Mixing
Valve and locate the block of four
switches marked SW1 on the circuit
board. Set switch 4 to ‘ON’ and loosely
replace the cover.
3.2. Power up the Mixing Valve. Wait ˜30
seconds for the LED to show “Yellow”.
3.3. Turn the remote control “on” by
turning the lever to the eco position.
Wait for the Mixing Valve LED to show
“Green” (this should only take a couple of
seconds). Turn the Remote Control “off”
by turning the lever back to the “off”
position.
3.4. Power down the Mixing Valve. Remove
the cover from the Mixing Valve, set switch
4 at SW1 to “off” and replace the cover.
The Mixing Valve and Remote Control are
now Paired.
Maximum Temperature Setting
The maximum temperture is factory
pre-set to 48ºC. To change the maximum
outlet water temperature follow the steps
below.
1. Power down the Mixing Valve and
remove the cover.
E
134
134
134
134
134

Commissioning - Functional Testing
20 Need help? Give us a call on 0844 701 6273 and speak to one of our trained advisers.
7. Once the pulsing stops, turn the
Controller Off.
8. To resume normal showering, simply
turn the Controller on as normal.
Basic functional Testing
Prior to using the shower the following
tests should be carried out to ensure the
Mixing Valve is working correctly.
Power on the Mixing Valve. Check the
display on the Remote Control is working.
Check flow control. Operate the lever to
all flow positions and check for increased
flow.
Check Temperature controls. Press the
and temperature buttons to check that
the temperature increases and decreases.
Check digital display. Ensure the
temperature display increases and
decreases when pressing the temperature
controls.
Checking Water / Plumbing Connections
Before using the shower for the first time
the installer needs to check that the
water/plumbing connections are correct.
The cold water supply pipework should
only be connected to the inlet marked
COLD on the Mixing Valve cover.
The hot water supply pipework should only
be connected to the inlet marked HOT on
the Mixing Valve cover.
Turn on the water supplies to the Mixing
Valve and open the stop / service valves to
the mixing valve.
Check that there are no leaks around the
connections to the inlets and outlet.
Purge Procedure
After checking the water / plumbing
connections and before using the shower
as normal the Mixing Valve will need to be
purged. Please run through the following
procudure.
1. Ensure both power and water supplies
to the Mixing Valve are on.
2. Turn the Controller On by rotating the
lever to any of the flow positions. The
shower will run.
3. Press and buttons at the same
time for 3 or more seconds then let go.
4. ‘0’ should be displayed. If not repeat
step 3.
5. Press button once. ‘1’ should be
displayed.
6. The purge sequence will now run.
(Short pulses of water output from the
shower for about 12 seconds).
E