Britex Elsa Arm Rest User manual

INSTALLATION NOTES
visit britex.com.au
for more quality products
Last Revised May 2018
STEP BY STEP INSTALLATION
STEP 1 : Pre Assembly - Place #3 30mm Washer onto
#2 Shoulder Bracket then add #4 Arm. Align #5 Pivot
Mount and attach onto shoulder bracket and arm piece
with 2 x #6 Button Head Screws.
STEP 2: Attach the #12 Leg to #4 Arm with #11 35mm
Screw & #8 M8 Washer from the inside and fasten with
another #8 M8 Washer and #7 Dome Nut.
STEP 3 : To Attach #9 Leg Support Bracket to #5Pivot
Mount, place 1 x #8 M8 Washer in between then on the
inside thread #11 35mm Screw through #10Bump Stop
and through the #9 Leg Support Bracket and #5 Pivot
Mount. Fix with 1x #8 M8 Washer #7 Dome Nut to the
outside of #5 Pivot Mount. Attach the other end of the
#9 Leg Support Bracket to the #1 Stud (attatached to
the #12Leg) with #8 M8 Washer in-between joint and
add external #8 M8 Washer and fasten with #7 Dome
Nut.
MELBOURNE
Britex Place Mirra Crt
Bundoora VIC 3083
t(03) 9466 9000
[e-mail]
SYDNEY
16 Northumberland Drv
Taren Point NSW 2229
t(02) 9531 2100
[e-mail]
PERTH
Unit 1/8 Principal Link
Malaga WA 6090
t(08) 9249 5464
[e-mail]
BRISBANE
19 Manilla St
E.Brisbane QLD 4169
t(07) 3363 2400
[e-mail]
ADELAIDE
The Britex Group
SA State Office
t1300 764 744
[e-mail]
AR-100
Installation & Trouble Shooting Guide for the:
*Included but not shown: Optional Removable Toilet Roll Holder and Additional Toilet Seat Bolts
Elsa Arm Rest
ITEM# Description Notes Qty
1Base Plate 1
2Shoulder
Bracket
1 per arm 2
330mm Washer 1 per arm 2
4 Arm Left x 1
Right x 1
2
5 Pivot Mount 1 per arm 2
6 M5 Button Head
20mm Screws
2 per arm 4
7 M8 Dome Nut 3 per arm 6
8M8 Washer 6 per arm 12
9Leg Support
Bracket
1 per arm 2
10 Bump Stop 1 per arm 2
11 35mm Screw 2 per arm 4
12 Leg 1 per arm 2
13 Foot 1 per arm 2
14 Stud Attached
to Leg
2
15 M3 button Head
Screw for Arm Pad
1 per arm 2
16 Blue Arm Pad 1 per arm 2
STEP 4: Push Blue Arm Pad onto 2# Arm, align fixing
holes and secure with #15 M3 Button Head Screw for
Arm Pad.
STEP 5 : Repeat the Steps for opposite Arm Rest.
STEP 6 : Remove Toilet Seat, processes may be different
depending on your style. (Additional complimentary
toilet seat extension bolts are included with your arm
rest to help with re-fixing your toilet seat)
STEP 7: Place #1 Base Plate on top of Pan. Slide #2
Shoulder Bracket underneath and align slots. Fasten
with Toilet Seat Brackets and re-fix Toilet Seat Fixings.
Keep slightly loose until repeated for other side, then
tighten all fixings.
STEP 8: Fasten Toilet Seat then adjust #13 Feet on the
Arm Rest by screwing down to the suitable height.
Enjoy the ease and safety of using the Elsa Arm Rest!
Note: Below correlate to item# above.
3
2 4
6
12
14
12
10
8
#
8
8
8
7
7
7
5
5
5
8
8
11
9
9
9
411
5
2
15
1 2
13

ITEM# Description Notes Qty 1Base Plate 1 2Shoulder
Bracket
1 per arm 2
330mm Washer 1 per arm 2 4 Arm Left x 1
Right x 1
2
5 Pivot Mount 1 per arm 2 6 M5 Button Head
20mm Screws
2 per arm 4
7 M8 Dome Nut 3 per arm 6 8M8 Washer 6 per arm 12 9Leg Support
Bracket
1 per arm 2
10 Bump Stop 1 per arm 2 11 35mm Screw 2 per arm 4 12 Leg 1 per arm 2 13 Foot 1 per arm 2 14 Stud Attached
to Leg
2
15 M3 button Head
Screw for Arm Pad
1 per arm 2
16 Blue Arm Pad 1 per arm 2