Brook XB Fighting Board User manual

EN
JP
TW
XB Fighting Board supports XB Original, XB 360, XB 1, XB X|S, allowing you to
play with your arcade stick on multiple platforms through wired connection.
★ Supporting Turbo, LED status display, key lock, and upgradable rmware!
★It also comes with an exclusive software for cong settings.
For more information, please visit the product website.
★The following description for the setting guide, will be written in button
combinations of the X-Series controller.
XB 1
XB X |S
XB 360
XB Original

Wire connection diagram
GND
Power
J6-1
GND D+ D- VDD_5V
1
1
1
XB
19
20
1
2
J2
J5
J1
RS
DP
LS
VCC
LSB
GND
RSB
RY
RX
LY
LX
GND
LT
RT
B
A
GND
LB
RB
Y
X
MENU
VIEW
GUIDE
GND GND
RIGHT
LEFT
UP
DOWN
1
SHARE LSB RSB GND
J13
1
VCC RESERVE TBKEY GND
J10
1
J3
LED+ LED- LOCK GND
3DVR_EN
GND
J9
1
SOCD GND
J14
J11J6
J8
J4
1
1
P4
P3
P2
P1
VCC
GND
D+
D -
VDD_5V
LT RT B A
LB RB Y X GUIDEVIEWMENU
VDD_5V
J5
LS
RS
DP
L-STICK
R-STICK
D-PAD
PLAYER
LED
SHARE
LOCK
LOCK LED
LSB
RSB
2
EN
JP
TW

3
J1/J9: Connecting analog stick
J9
J9
Removed
Installed
Enable
Disable
J9
Remove
Jumper
Step 1. Step 2.
J1
L-Stick
R-Stick
VCC
LSB
GND
RSB
RY
RX
LY
LX
As J2 and J4 have the same functions, only one of them is needed for
the connection, it is recommended to use the dedicated cable
"BROOK Fighting Board Cable".
J2/J4/J13: Connecting buttons and digital joystick
J2 pin names
19
20
1
2
VCC GND RT A LB Y
RIGHT UP
MENU VIEW
VCC
GND
LT
B
GND
RB
GUIDE
LEFT
DOWN
X
J2
J4 pin names
J6-1
GND D+ D- VDD_5V
1
1
XB
J5
DP
LS
LT RT B A GND LB RB Y X MENU VIEW GUIDE GND GND RIGHT LEFT UP DOWN VDD_5V GND
SOCD
J11J6
J4
1
P4
P3
P2
P1
VCC
EN
JP
TW

J5: LS/DP/RS ON/OFF switch
DP Mode (default): Joystick input corresponds to D-Pad output.
LS Mode: Joystick input corresponds to Left 3DVR(Lx/Ly) output.
RS Mode: Joystick input corresponds to Right 3DVR(Rx/Ry) output.
If the analog stick (J9 short circuit) and ON/OFF switch (J5: DP
mode) are not needed, press the following button combinations
for 3 seconds to change the joystick input mode.
＊When successfully switched, all Player LED will go dark for 1 second.
= L-Stick
= D-Pad
= R-Stick
+
+
+
4
J3: Key lock
You can turn o the dierent functions that may be determined as
illegal in ocial competitions,include: Guide, Menu, and View buttons.
When the LOCK LED is on, it means that the key function lock is on.
When the LOCK LED is o, it means that the key function lock is o.
EN
JP
TW
XB
19
20
1
2
J2
J5
J1
RS
DP
LS
VCC
LSB
GND
RSB
RY
RX
LY
LX
GND
LT
RT
B
A
GND
LB
RB

J6/J6-1/J8: Connect the console
Choose one USB interface with a corresponding USB extension cable
for the connection.
＊When using J6 and J6-1, please double-check whether the
corresponding pin order is correct.
＊Improper connection may cause the ghting board to burn.
G D+ D- V
J6-1
Red
White
Green
Black
G
D+
D-
V
Red
White
Green
Black
J6
J6-1
GND D+ D- VDD_5V
1
1
Y
X
MENU
VIEW
GUIDE
GND
1
SHARE LSB RSB GND
J13
1
J10
1
3DVR_EN
GND
1
J6
J8
GND
D+
D -
VDD_5V
5
EN
JP
TW

J10: Turbo function setting
＊There are 5 speed modes for the Turbo function: 5, 10, 15, 20, 25 Hit/Sec.
＊When the Player LED is ashing, it means that Turbo function of the
pressed button has been activated.
Buttons available for Turbo function setting:
D-Pad, A, B, X, Y, LB, RB, LT, RT, LSB, RSB
Turbo function setting method:
Press the Turbo button and press the selected button, to activate or
deactivate the Turbo function of the selected button.
Press the following button combinations to adjust Turbo speed:
= Speed Up
= Speed Down
+
+
TB
TB
The operation status of the ghting board are all displayed through the
Player LED. Connection of the Player LED is essential to conrm the
operation status of the controller.
J11: Player LED display
6
EN
JP
TW

This layout is only for referencing
TURBO
Player LED
D-PAD
LS/DP/RS
LOCK
GUIDE VIEW MENU
SHARE
LBRB
Y
X
A
BRT LT
LSB
RSB
LOCK LED
Arcade Stick layout design reference
Correspondence table of the button functions
7
D-PAD
A
B
X
Y
LB
RB
LT
RT
LSB
RSB
L-Stick
R-Stick
START
BACK
GUIDE
--*
D-PAD
A
B
X
Y
White
Black
LT
RT
LSB
RSB
L-Stick
R-Stick
START
BACK
--*
--*
XB 360XB 1XB Series XB Original
*No function.
D-PAD
A
B
X
Y
LB
RB
LT
RT
LSB
RSB
L-Stick
R-Stick
MENU
VIEW
GUIDE
--*
D-PAD
A
B
X
Y
LB
RB
LT
RT
LSB
RSB
L-Stick
R-Stick
MENU
VIEW
GUIDE
SHARE
EN
JP
TW

8
Automatic:
It can automatically detect the consoles (for XB 360, XB 1, and
XB Series consoles).
＊For XB Original, manual console switch is required.
Manual console switch:
After pressing and holding the button in the table below, connect
the device to the game console to switch to the corresponding
mode of the selected device.
＊If you press and hold the menu button at the same time, the
device mode will be saved. After unplugging and replugging, it
will automatically switch to the previously assigned device mode.
＊Switch to the cong setting device with the exclusive software to
perform the cong settings.
Light display of device modes:
Cong Setting
1P
2P
3P
4P
XB 360 XB Original
= Cong Setting
＊ = Player LED ON, = Player LED OFF
How to switch between dierent consoles?
= XB 1, XB Series
= XB 360
X
Y
= XB Original
= Auto Detect (Default)
RB
LB
EN
JP
TW

9
Press the button combinations for 1 second to change to the following
four sets of button congurations.
＊When successfully switched, all Player LED will go dark for 1 second.
= Cong 1
= Cong 2
= Cong 3
= Cong 4
+
+
+
+
A
B
RT
LT
Switching between button cong sets
EN
JP
TW

Simultaneous Opposing Cardinal Directions.
1. Default setting is mode 1.
2. SOCD will be automatically saved.
Switch method
Please hold down the corresponding button rst, then insert the
power cable into the console to switch modes.
Mode 1
Mode 4Mode 3
Mode 2
Mode 1 Mode 2 Mode 3 Mode 4
UP Priority Last Priority
CAPCOM / Neutral BYPASS
Neutral
Neutral
Neutral
10
SOCD Mode Switching Tutorial
EN
JP
TW

The following table consists of the keywords and their
abbreviations used in the description:
The following table consists of the keywords and their symbols used
in the description:
Keyword
XBOX Original
XBOX 360
XBOX One
XBOX Series
Direction Pad
Left Stick
Right Stick
XB Original
XB 360
XB 1
XB Series
DP or D-Pad
LS or L-Stick
RS or R-Stick
Abbreviation
= Menu
= View
= Turbo Key
TB
= D-Pad Up
= D-Pad Down
= D-Pad Left
= D-Pad Right
Other
11
EN
JP
TW

12
XB series product update pre-operation steps
Once consent is given, your (consumer) information will be shared, and how this
information will be utilized is unknown. Consumers have the right to refuse to
provide it and protect their personal information.
Press the XBOX button on the
home page.
1
Select "Settings" in
"User Icon".
2
Select "Console info" in
"System".
３
Select "Data collection".
６
Change "You can share
optional data" to "Block"
７
Uncheck "Allow optional data
collection".
４
Select "Privacy & online Safety"
in "Account".
５
Precautions Before Setup
EN
JP
TW

XB 1
XB X |S
XB 360
XB Original
XBOX 格鬥板支援 XBOX Original、XBOX 360、XBOX One、XBOX
Series 主機，允許你的大搖台以有線連接方式於各遊戲平台上進行遊戲。
★ 支援 Turbo 功能設定、LED 狀態顯示、功能鎖及線上更新功能！
★另搭配專屬設定軟體，可作 Config 設定。
相關資訊請至產品資訊網頁查詢。
★以下皆以 X-Series 控制器按鍵定義，作設定說明。
EN
JP
TW

線路連接圖
GND
Power
J6-1
GND D+ D- VDD_5V
1
1
1
XB
19
20
1
2
J2
J5
J1
RS
DP
LS
VCC
LSB
GND
RSB
RY
RX
LY
LX
GND
LT
RT
B
A
GND
LB
RB
Y
X
MENU
VIEW
GUIDE
GND GND
RIGHT
LEFT
UP
DOWN
1
SHARE LSB RSB GND
J13
1
VCC RESERVE TBKEY GND
J10
1
J3
LED+ LED- LOCK GND
3DVR_EN
GND
J9
1
SOCD GND
J14
J11J6
J8
J4
1
1
P4
P3
P2
P1
VCC
GND
D+
D -
VDD_5V
LT RT B A
LB RB Y X GUIDEVIEWMENU
VDD_5V
J5
LS
RS
DP
L-STICK
R-STICK
D-PAD
PLAYER
LED
SHARE
LOCK
LOCK LED
LSB
RSB
2
EN
JP
TW

3DVR_EN
3
J1、J9：連接類比搖桿
J9
J9
Removed
Installed
Enable
Disable
J9
移除
Jumper
Step 1. Step 2.
J1
L-Stick
R-Stick
VCC
LSB
GND
RSB
RY
RX
LY
LX
J2 與 J4 功能相同，二選一即可，推薦使用專用排線
『Fighting Board Cable』。
J2、J4、J13：連接按鍵及數位搖桿
J2 接腳名稱
19
20
1
2
VCC GND RT A LB Y
RIGHT UP
MENU VIEW
VCC
GND
LT
B
GND
RB
GUIDE
LEFT
DOWN
X
J2
J4 接腳名稱
J6-1
GND D+ D- VDD_5V
1
1
XB
J5
DP
LS
LT RT B A GND LB RB Y X MENU VIEW GUIDE GND GND RIGHT LEFT UP DOWN VDD_5V GND
SOCD
J11J6
J4
1
P4
P3
P2
P1
VCC
EN
JP
TW

J5: LS/DP/RS 切換開關
＊切換操作成功時，Player LED 全滅一秒。
= L-Stick
= D-Pad
= R-Stick
+
+
+
4
J3: 按鍵鎖
可關閉在正式競賽中使用會判定失敗的各項功能，包含關閉
Guide、Menu、View 按鍵功能。
LOCK LED 亮，表示已開啟功能鎖。
LOCK LED 滅，表示為關閉功能鎖。
DP Mode（預設）：搖桿輸入對應至 D-Pad 輸出。
LS Mode：搖桿輸入對應至左 3DVR （Lx、Ly）輸出。
RS Mode：搖桿輸入對應至右 3DVR （Rx、Ry）輸出。
若不使用類比搖桿 (J9 短路 ) 及切換開關 (J5：DP mode)，
可按住組合鍵三秒切換以下搖桿輸入對應功能。
EN
JP
TW
XB
19
20
1
2
J2
J5
J1
RS
DP
LS
VCC
LSB
GND
RSB
RY
RX
LY
LX
GND
LT
RT
B
A
GND
LB
RB

J6/J6-1/J8: 連接遊戲主機
選擇一個 USB 接口，搭配相應的 USB 延長線連接使用。
＊使用 J6、J6-1 時請注意相對應的腳位順序是否正確，
不當連接可能導致格鬥板燒毀。
G D+ D- V
J6-1
Red
White
Green
Black
G
D+
D-
V
Red
White
Green
Black
J6
J6-1
GND D+ D- VDD_5V
1
1
Y
X
MENU
VIEW
GUIDE
GND
1
SHARE LSB RSB GND
J13
1
J10
1
3DVR_EN
GND
1
J6
J8
GND
D+
D -
VDD_5V
5
EN
JP
TW

J10: Turbo 功能設定
= Speed Up
= Speed Down
+
+
TB
TB
J11: Player LED 顯示
6
能設定 Turbo 的功能鍵：
D-Pad, A, B, X, Y, LB, RB, LT, RT, LSB, RSB
Turbo 設定方式：
按住 Turbo 鍵並按下能設定 Turbo 的功能鍵，即可開啟或關閉該
功能鍵的 Turbo 功能。
按壓以下組合鍵可調整 Turbo 速度：
＊Turbo 速度共分五段：5、10、15、20、25 Hit/Sec。
＊當 Player LED 閃爍時，代表被按住的按鍵已開啟 Turbo 功能。
格鬥板操作狀態皆由 Player LED 顯示，必須連接 Player LED 才
能夠確認目前控制器操作狀態。
EN
JP
TW

擺設樣式僅供參考
TURBO
Player LED
D-PAD
LS/DP/RS
LOCK
GUIDE VIEW MENU
SHARE
LBRB
Y
X
A
BRT LT
LSB
RSB
LOCK LED
Arcade Stick 佈局設計參考
按鍵功能對應表
7
D-PAD
A
B
X
Y
LB
RB
LT
RT
LSB
RSB
L-Stick
R-Stick
START
BACK
GUIDE
--*
D-PAD
A
B
X
Y
White
Black
LT
RT
LSB
RSB
L-Stick
R-Stick
START
BACK
--*
--*
XB 360XB 1XB Series XB Original
*無功能
D-PAD
A
B
X
Y
LB
RB
LT
RT
LSB
RSB
L-Stick
R-Stick
MENU
VIEW
GUIDE
--*
D-PAD
A
B
X
Y
LB
RB
LT
RT
LSB
RSB
L-Stick
R-Stick
MENU
VIEW
GUIDE
SHARE
EN
JP
TW

8
裝置模式燈號顯示：
= Cong Setting
＊ = Player LED ON, = Player LED OFF
如何切換各主機平台？
= XB 1, XB Series
= XB 360
X
Y
= XB Original
= Auto Detect (Default)
RB
LB
自動切換：
可自動偵測主機平台 ( for X-360、、X-One、X-Series 主機 )。
＊X-Original 需手動切換。
手動切換：
按住下表中的按鈕後，將設備連接到遊戲機以切換到所選設備
的相應模式。
＊如果在操作中同時按住菜單按鈕，則設置將自動保存。
下次連接時，它將以已保存的設備模式啟動。
＊切換至 Config Setting 裝置並搭配專屬設定軟體可作
Config 設定。
Cong Setting
1P
2P
3P
4P
XB 1, XB Series XB 360 XB Original
EN
JP
TW