Brother P-TOUCH H110 User manual

English
User’s Guide
H11
0

GETTING STARTED
Power Supply and Tape Cassette
Open the cassette cover by pressing the
highlighted area at the top end of the machine.
• Make sure you turn the power off when replacing batteries
or tape cassettes.
Insert a tape cassette, making sure it snaps into
place.
• Make sure the end of the tape feeds under the tape guides.
• Use Genuine Brother P-touch TZe tapes with this machine.
1
Print head
Tape cutter leverCassette cover
1
Tape exit slot
Toothed Wheel
Cutter's edge
End oftape
Tape guides
2
With your new Brother P-touch labelling machine, you can create a wide variety of custom, self-adhesive labels. This
machine uses Brother "TZe" tapes from 3.5 mm to 12 mm widths. "TZe" tape cassettes are available in many
colours and sizes. Visit
www.brother.com for a complete list of tapes that work with your machine.
Read this manual carefully before starting and keep it in a handy place for future reference.
Printed in China
LAK038001
English
User’s Guide
H11
0
NOTE
When using the optional AC adapter
1. Insert adapter cord into the AC adapter socket at the bottom of the machine.
2. Insert the plug into the nearest standard electrical socket.
For the memory backup feature, use either AAA alkaline batteries (LR03) or Ni-MH batteries (HR03)
together when using the AC adapter.

Insert six new AAA alkaline batteries (LR03) or fully
charged Ni-MH batteries (HR03), making sure their
positive and negative ends point in the correct directions.
Users of alkaline batteries:
Always replace all six batteries at the same time
with brand new ones.
Users of Ni-MH batteries:
Always replace all six batteries at the same time
with fully charged ones.
1Insert the two hooks at the bottom of the
cassette cover into the slots on the
machine.
2Securely close the cassette cover making
sure it snaps into place.
3
AC adapter socket
4

NOTE
• The LCD displays one row of 15 characters; however, the text you enter can be up to 80 characters in
length.
• Label length displayed on the LCD may differ slightly from the actual printed label length.
LCD
1. Size
2. Font
3. Cursor
4. Shift
5. Caps
6. Underline/Frame
7. Style
8. Label Length
If a specific label length has
been selected, also appears.
9. Cable
1
2
3
8
6
7
5
4
9
1Turn your machine on.
Supply power using six AAA batteries or the optional AC adapter (AD-24ES/AD-5000ES: For Australia,
New Zealand only), and then press to turn the power on.
2Set the language.
The default setting is [English].
3Set the unit of measurement.
The default setting is [mm].
NOTE
• The machine automatically turns off if no keys are pressed within five minutes.
• To cancel any operation, press .
• After pressing , the machine displays "Accepted" to confirm your settings.
Initial Settings
/[Language] /[English/Español/Français/Hrvatski/Italiano/
Magyar/Melayu/Nederlands/Norsk/Polski/Português/Portug. (BR)/Română/Slovenski/Slovenský/
Suomi/Svenska/Türkçe/ýeština/Dansk/Deutsch] .
/[Unit] /[inch/mm] .

NOTE
• While selecting the settings, press the Space key to revert to the default item.
• Pressing the Preview key displays a generated image of the label, and may differ from the actual label
when printed.
Keyboard
1. Menu key
2. Power key
3. Cursor key: Left (Use with the
Shift key to go to the top of the
text.)
4. Escape key
5. OK key
6. Size key
7. Font key
8. Character key
9. Shift key
10. Caps key
11. Accent key
12. Tape cutter lever
13. Clear key
14. Print key
15. Preview key
16. Cursor key: Right (Use with the
Shift key to go to the end of the
text.)
17. Style key
18. Frame key
19. Cable key
20. Backspace key
21. Enter key
22. Symbol key
23. Space key
1
2
3
4
7
5
6
9
8
10
11
21
13
12
14
16
17
18
19
22
23
15
20

GETTING STARTED (Continued)
This function allows you to set the brightness of
the LCD. You can select from five levels of
brightness.
The default setting is [0].
• To change a setting back to default, press the
Space key.
BASIC USAGE
XSwitching Upper-Case/Lower-Case
Press to switch between upper and lower
case text.
Upper-case ( ON) Lower-case ( OFF)
XCreating Two-Line Labels
Move the cursor to where you want to start the
next line and press . Use either 9 mm or 12
mm wide tape for two line printing.
NOTE
• The return symbol ( ) is displayed when you
press the Enter key, indicating you have chosen to
input a second line of text.
XEntering Accented Characters
Press to add an accented character.
• See the table of accented characters included in
this guide.
• To cancel an operation, press .
• The order of accented characters depends on
the selected LCD language.
Contrast
/[LCD contrast]
/[-2/-1/0/+1/+2]
1
Entering Text
Line 1 Label image
Line 2
- /
2
Caps
Caps

XChanging Label Width
XChanging Label Length
NOTE
• After the label is printed, cut along the printed
dots (:) with scissors so that the label length
matches what is displayed on the LCD.
• If a specific label length has been selected,
also appears in the LCD.
• By pressing the Space key, [Auto] is displayed.
• To change a setting back to default, press the
Space key.
XDeleting Text
NOTE
XPreview
You can preview the text before printing.
• Pressing the Preview key displays a generated
image of the label, and may differ from the
actual label when printed.
• When the LCD cannot display all the text at
once, press /to display the hidden
text.
• Press // to leave the preview
mode.
XFeeding (Tape Feed)
• This function feeds approximately 25 mm of
blank tape.
Entering Text (continued)
/[Width]
/[Normal/x2/x1/2]
Width Normal
× 2
× 1/2
/[Label Length]
/[Auto/30-300 mm]
Press .
• To delete all text and settings or text only,
press
/[Text&Format]/[Text Only]
Printing Labels
/[Feed]

BASIC USAGE (Continued)
XPrinting
• If you need only one copy of the label, press
without selecting the number of copies.
• You can print up to nine copies of each label.
• The number of copies can also be specified by
pressing a number key.
• To cut the label, press the tape cutter lever on
the upper-right corner of the machine after the
message "Please Cut" is displayed. "Please
Cut" is displayed on the screen for two seconds.
• To prevent damage to the tape, do not touch the
cutter lever while the message "Please Wait" is
displayed.
• To remove the backing, fold the label
lengthwise with the text facing inward to expose
the inside edges of the backing. Peel off the
backing one piece at a time and apply.
XUsing Print Options
[Numbering]
You can print a series of up to nine labels at a time
using auto-numbering. Using this feature you can
automatically increase a selected number by one
after each label is printed. The numbers of labels
you can print at one time depend on the initial
number.
Example: To print copies of a label containing a
serial number (0123, 0124 and 0125)
• Select the highest number you want to be
printed when setting the number.
[Mirror]
Example: Follow the instructions below after
entering "J.SMITH" if you want to
Mirror Print "J.SMITH".
• Use clear tape in [Mirror], so you can read the
labels correctly from the opposite side when
attached on glass, windows or other
transparent surfaces.
XSetting Margin ( )
[Full]/[Half]/[Narrow]
For leaving equal margins on both sides of the
text.
NOTE
• The 25 mm piece of tape that is produced prior
to every label cannot be eliminated due to the
construction of the tape mechanism.
However, when you print more than one label
continuously, the subsequent labels can be
printed without the excess tape. (Except for the
full margin setting)
Printing Labels (continued)
2
[Copies: ] //-
Enter numbers /Move the cursor
to the number you wish to increment
/[Print
Option] [Numbering]
/
Enter text/characters /
[Print Option] /[Mirror]
[Mirror Print?]
/[Margin]
/[Full/Half/Narrow/Chain Print]
ABC ABCABC
4 mm4 mm12 mm 12 mm 25 mm 25 mm
Full Half Narrow

[Chain Print]
Use this setting when printing several labels with
minimum margins.
1. Enter text.
2. Press , then [Copies: ] appears.
3. Press /or enter a number with
number keys to select the number of copies.
4. Press . Printing starts, and then the
message "Feed OK?" appears.
5. Press to enter more text.
6. Clear the text, enter the text for the next label,
and then press .
7. When the message "Feed OK?" appears after
the last label is printed, press .
8. After the tape is fed, press the cutter lever to
cut off the chain of labels.
NOTE
• When you set [Chain Print], feed the tape before
using the cutter otherwise a part of the text may
be cut off.
• When you set [Half] or [Narrow], the displayed
label length is the length from the printed dots
( ) to the end of the label. Cut along the printed
dots (:) with scissors.
• To print more than one copy of a label with
minimum margins, set the margin to [Narrow].
• Do not pull the tape since this may damage the
tape cassette.
You can save up to 15 labels and recall them for
printing at a later date. A maximum of 80
characters can be saved per file, a maximum of
1200 characters can be saved in total memory.
You can also edit and overwrite the stored labels.
XSave
XPrint
XOpen
NOTE
• You can also enter the File menu by pressing
.
• If you try to store a label when there is already a
label stored to that number, a message
“Overwrite OK?” appears. Press to save
your new label. Press to cancel.
• You must type text before starting the save
function.
Printing Labels (continued)
LCD Label image
Full
Half
Narrow
67 mm
ABC
41 mm
ABC
25 mm
ABC
Saving Label Files
Enter Text /[File]
/[Save] /
/[File]
/[Print] /
[Copies: ]
//-
/[File]
/[Open]
/

USING TEMPLATES
This function allows you to create two types of
cable labels.
Example: Cable Label 1
NOTE
• Label length is auto only. You cannot set label
length.
• To clear all text and settings or text only, press
/[Text&Format]/[Text Only]
.
• You can set the Font, Size, Style and Frame
while entering texts.
• To exit templates and return to the text input
screen, do one of the following:
a) Press .
b) Press /to select [Exit], and then press
when "Print" appears.
• To preview labels, press the Preview key when
[Print] is displayed on the LCD.
• You cannot save labels created using templates
to memory.
This function allows you to create various labels
using the built-in templates. See the Text Label
templates table included in this guide.
XExample:
[Template that includes one
repeated graphic]
NOTE
• Press the Space key to return to the initial
setting for "Label Length" mode. The initial
setting is [Auto].
• To clear the text, move the cursor to the right side
where you want to clear, and then press .
• To clear all text, press , then “All Clear”
appears. Press to clear. Press to cancel.
• You cannot set the Font, Size, Style and Frame
while entering text.
• If you set the longer label length than the default
([Auto]), the text label is printed repeatedly
within the set length. The text label may not be
fully printed depending on the set length.
• The available label length setting changes
depending on the number of texts you entered.
• These templates are available when using
12 mm wide tape cassettes.
• You cannot edit the templates.
3
Cable Label
Cable Label template 1 :
Cable Label template 2 :
[Select Layout] /
[Input Text] Enter
text[Print]
[Copies: ] //-
Text Label
/[Decorative]
[Select Category] /[Text]
[Select Design] /
[Input Text]
[Set Label Length] / [Auto/30-
999 mm]
[Print] [Copies: ] /
/-