Brown Jordan Stainless Outdoor Kitchen Cabinet User manual

Stainless Outdoor Kitchen Cabinets
Installation Instructions
Thank you for purchasing our cabinets!
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 1 of 17
Revised: 10/17/2017

INSTALLATION TIPS AND PREP
Prepare Area for Kitchen:
Make sure your landscape area is as level as possible and that there will be minimal additional
landscaping to be performed after cabinets are installed.
Notes and Installation Tips:
Upon receipt of cabinets:
Carefully review packing list to verify your order has been shipped complete and carefully
unpack cabinets making sure not to scratch Stainless Steel fronts and not to lose or
misplace any accessories or hardware.
Hardware (pulls, hinges, rivets, screws, etc.) is in a small box in each cabinet.
Doors are not installed to protect the cabinet sides during shipping. All cabinets will have
doors packed separately (drawers ARE shipped installed), some will be in the box with the
cabinet and some will be in a separate box (when an accessory is installed). A label will be
on each cabinet box with this information.
Uninstall shipping brackets from appliance cabinets and reinstall in proper position near
the back of those cabinets where they act as counter top supports BEFORE ATTACHING
ADDITIONAL CABINETS.
Basic Notes on Installation:
Install cabinets in final position. Cabinets are not easy to move after assembly is complete.
Install first cabinet at highest point so toe kick area is minimum 4 ½”. Then install
adjacent cabinets. This insures that the toe kick will fit under all cabinets without
needing to cut it down in the field.
DO NOT remove vinyl protective coating until installation is complete. Peel back vinyl
covered areas where it will be hard to remove after install (e.g. back and side panels,
fillers).
Remove all drawers before installation. This will make cabinets easier to lift and install
and give access to installation hardware. Squeeze plastic clips under front sides of
drawer to release and lift drawers off under mount slides.
Install cabinets completely (cabinets screwed together, counter top installed, appliances
installed, doors installed, drawers returned to original positions and level is obtained)
before attempting to adjust doors or drawers.
Cabinets may flex until they are locked into place when screwed to one another.
Tighten screws on top rails (if necessary) prior to installation. Attach single cabinets to
frame in masonry, stucco, stone or one-piece island installations.
1/8” bumpers are inserted between drawers to protect the drawer heads during
shipping. They may be discarded with the protective peel coat.
Tools you will need: Power screw gun (#2 Phillips), #2 Phillips head manual screw
driver, level, tape measure
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 2 of 17

ASSEMBLY & INSTALLATION
STORAGE CABINET ASSEMBLY
Verify product number(s) on box(es) to order.
Carefully unpack cabinets making sure not to scratch stainless steel fronts. Stainless is protected
by a plastic coating that must be removed after setup. All cabinets will have doors packed
uninstalled. Those with interchangeable doors (right or left opening) will use the supplied caps to
cover holes after the hinge side has been chosen.
1.
Remove and check hardware bag/box that contains legs, hinges, hinge plates, screws (#8
(smaller) to install hinge plates to cabinet walls, small countersunk screws to attach hinges
to cabinet doors and #10 (larger) for all other assembly and attaching cabinets to one
another, screws for pulls), pulls (handles), extra bumpers, plastic edge guard for access
holes, hinge hole covers. Also packed with the cabinet is a TOP BRACKET CONNECTOR.
Since one top bracket connector is with each cabinet, you will end up with one extra when
you finish installation.
2.
Remove foam packing material and discard.
3.
Remove drawers and accessories that may hinder assembly and store in a safe place.
4.
Put cabinet on its back and install the legs in receivers (leg cups) attached to bottom of each
cabinet. Simply push in until snug.. Preset all legs to about 4 1/4” to speed leveling process.
4 1/4” is approximately where the bottom of the leg body is even with the top of the black
leg adjuster. When installed, toe kick area will be 4 ½”.
Install the doors by first installing the hinge plates to the cabinet walls using #8 screws
supplied. Install the hinges to the backs of the doors using the small countersunk screws
supplied. Then install the doors by slipping the large screw from the hinge plate into the
opening in the hinge and tightening it near the etched vertical line on the hinge. This will
space the door close to its final position.
Install any optional shelving or internal accessories with supplied #10 screws in holes
provided on the sides of the cabinet from the inside-out.
5.
6.
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 3 of 17

Toe Kick—install
clip with Velcro to
white side
Leg,
Receiver
Foot Installation
Use #8
screw;
Vertical
alignment
Countersunk
screws here;
PVC backer
Attachment
screw; also
front to back
alignment
Horizontal
alignment
Door Installation
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 4 of 17

APPLIANCE AND GRILL CABINET ASSEMBLY
Verify product number(s) on box(es) to order.
Carefully unpack cabinets making sure not to scratch stainless steel fronts. Stainless is protected
by a plastic coating that must be removed after setup. All cabinets will have doors packed
uninstalled.
The shipping bracket must be removed and relocated to be the counter top support bracket towards
the rear of the cabinet.
1.
Remove and check hardware bag/box that contains legs, hinges, hinge plates, screws (#8
(smaller) to install hinge plates to cabinet walls, small countersunk screws to attach hinges
to cabinet doors and #10 (larger) for all other assembly and attaching cabinets to one
another, screws for pulls), pulls (handles), extra bumpers, plastic edge guard for access
holes, hinge hole covers. Also packed with the cabinet is a TOP BRACKET CONNECTOR.
Since one top bracket connector is with each cabinet, you will end up with one extra when
you finish installation.
2.
Remove foam packing material and discard.
3.
Remove shipping bracket from front of appliance cabinet and using the same screws,
relocate to the back of the unit. This will become the rear counter top support. Its location is
dependent upon the depth (front to back) of the grill/appliance, so it is necessary at this point
to find the grill manufacturer’s specified depth. Take the manufacturer’s depth and add ½”
to the measurement. Then measure from the front, including the door or trim, and locate
the pre-drilled holes at that location in the cabinet side walls. Using the original #10 screws,
attach the bracket so it is flush with the top of thecabinet.
4.
Note on grills that DO NOT hang from counter top:
Cabinets designed for appliances
that sit on the deck of the cabinets (e.g. Viking, Dacor, etc.) are shipped with spacers to shim
the grill to the height of most granite countertops. If the counter is more than 1 ¼” thick,
additional shimming must be used (not supplied).
Put cabinet on its back and install the legs in receivers (leg cups) attached to bottom of each
5.
cabinet. Simply push in until snug.. Preset all legs to about 4 1/4” to speed leveling process.
4 1/4” is approximately where the bottom of the leg body is even with the top of the black
leg adjuster. When installed, toe kick area will be 4 ½”.
Grill/appliance cabinets come with 2 front counter top supports or “U” brackets. These are
installed behind the side trim pieces using #10 screws. They are not interchangeable; align
them on the left or right to where the pre-drilled holes match up.
Grill/appliance cabinets come with 2 bottom and 4 rear access holes (2 bottom rear and 2 top
rear). Gas plumbing is usually run through the holes in the floor of the cabinet and then
through the holes in the SS shelf to the fitting on the grill (either left or right side depending
on the manufacturer). The plates on the remaining holes may be removed to allow airflow to
meet local building codes.
Handles are found in the hardware bag (if supplied). Remove the vinyl protective coating
prior to installing the handles; then install them using the screws provided.
6.
7.
8.
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 5 of 17

9.
“U” Bracket Counter
Top Support
Top Rear
Access Holes
Front
trim
SS Shelf
Side Access
Hole
Grill/Appliance Base
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 6 of 17
Sit on SS Shelf
Dacor
TEC
Viking
Wolf
Hasty-Bake (charcoal)
Hang on Counter Top
Alfresco Kitchen
Aid BBQ Galore Lynx
Cal Flame Napoleon
Capital Profire
DCS Solaire
Dynasty Twin Eagles
Fire Magic Vermont castings
GE Vidalia
Jenn Air Vintage
Shipping Bracket
Becomes Rear
Counter Top Support
Move From Front!!!
Stiffeners/shims “A” only
required for grills that sit
on SS shelf!

CABINET INSTALLATION/JOINING CABINETS
1. Place cabinet(s) in approximate final position. Use the cabinet that would be on the highest
ground to set the height first and allow at least 4 ½” of toe kick height. This will insure that
the toe kick will fit.
Tip: If kitchen space is fairly level, place grill cabinet first since it is the most difficult to move
around.
Partially install #10 screws in Easy-Alignment holes (2nd from bottom on front and rear
flange) on right side of cabinet. These will slip into the “dog bone” alignment holes on the
left side of the adjacent cabinet.
Using the adjustable legs, level cabinet in all directions, remembering to keep the 4 ½” leg
height for the toe kick.
Begin installing cabinets adjacent to the first level cabinet: If working to the left, tip and lift
adjacent cabinet so the Easy-Alignment screws slip into the “dog bone” alignment slots on
the left side of the first cabinet flange. If working to the right, tip and lift so the dog bone
slot slips over the partially installed screw. Make all cabinets close to level and use legs to
align the cabinets. Tighten front alignment screw from inside access hole on left side when
cabinets are aligned with each other. Then install top bracket connector with supplied
screws.
2.
3.
4.
Tip: If cabinets are installed in an island format where the back is accessible, you may tighten rear
alignment screw at back flange. If installed against a wall or the back is otherwise inaccessible, rear
tightening is not necessary.
5.
Continue installation in the same fashion for all cabinets. Make sure all legs are touching the
ground and supporting the cabinet’s weight.
Install the doors by first installing the hinge plates to the cabinet walls using #8 screws
supplied. Install the hinges to the backs of the doors using the small countersunk screws
supplied. Then install the doors by slipping the large screw from the hinge plate into the
opening in the hinge and tightening it near the etched vertical line on the hinge. This will
space the door close to its final position. TIP: Use a straight edge across both hinges to align
them before screwing them in.
Cabinet doors must only be adjusted when cabinets are level in final position! There are
two adjustment screws on the hinge receiver and the hinge plate mounting screws allow for
up and down movement. Trying to adjust doors too soon is a waste of time.
6.
7.
a.
The front screw is used to center the door in the opening. Turning the front screws in
or out will center the door over the cabinet opening.
The back screw is used to align the front of the door with the cabinet frame and
secure the door to the cabinet. Slightly loosen the screw and slide door in or out.
Retighten the screw to secure the door.
Loosen the hinge plate mounting screws and slide the hinge plates up or down for
further adjustment. Retighten the screws.
b.
c.
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 7 of 17

Top
Bracket
Dog
Bone
#10 Screw
1 Front
1 Rear
Access Hole
This Side (To
Tighten Screw)
Flange
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 8 of 17
Joining Cabinets
1) Install 2 screws in right flange of left
cabinet (2nd hole up), Do Not tighten;
screw half way in
2) Tip & lift either cabinet over screw heads
through “Dog Bone” hole
3) LEVEL CABINETS TOGETHER
4) Tighten 2 screws from Step 1 through
Access Holes (InsideCabinet)
5) Place top bracket over sides of adjacent
cabinets; slide bracket front to rear until 4
holes align and install 4 #10 screws
6) Cabinets should now be firmly attached

BACK, SIDE PANEL AND FILLER INSTALLATION
Back Panels
Optional Back Panels are available for all cabinets. Back panels are ordered based on cabinet size
(e.g. OBP18 for an 18” cabinets, OBP24 for a 24” cabinet, etc.). If a cabinet is larger than 30” wide,
you will need 2 back panels equal to the length of the cabinet (e.g. two OBP18 for a 36” cabinet,
two OBP21 for a 42” cabinet, etc.).
Back Panels for appliance cabinets are made with vents to allow air flow and to keep gas from
being entrapped between the back of the cabinet and the back panel. Vented back panels (OBPV)
are ordered the same way as non-vented back panels (e.g. OBPV18 for a 18” side burner cabinet,
two OBPV31 for a 62” grill cabinet, etc.).
Back panels extend the depth of the cabinets by ¾”!
Back panels are designed to fit in the exact width of the cabinet!
Side Panels
Optional Side Panels are available for all cabinets in several standard depths. Cabinets are designed
to have the seam between the side panels and back panels at the back. So if you are using back
panels, you need to order side panels that extend beyond the back of the cabinet by ¾” (e.g. OSP 25
5/8 for 24”D cabinets, OSP28 5/8 for 27”D cabinets and VSP30 5/8” for Viking 29”D cabinets.
If you are installing side panels without back panels (e.g. against a wall) you can order them for the
exact depth of the cabinets in which case you need to order lefts and rights. Many customers like to
install the cabinet backs away from the wall in which case you can order the larger standard size
side panels or custom widths (which include an engineering charge).
Side panels extend the width of the cabinets by ¾”!
Side panels are designed to extend to the face of the cabinet door!
Galvanized Filler Panels
Many installations call for adhering cement board (e.g. Hardibacker) with stucco or cultured stone
directly to the sides of the cabinets. Galvanized filler panels can be installed in the sides and backs
of the cabinets to make the walls flush to the flanges. Simply screw the cement board, lath, foam
board, etc. to the galvanized filler panels to complete the finished sides and backs.
Galvanized filler panels DO NOT extend the depth or the width of the cabinets!
To Install Panels:
1. Install 2 #10 screws in the bottom two holes of the panel. Screw all the way in. These are
only for aligning the panel in the side orback!
2. Align the screw heads on the bottom of the panel from Step 1 with the large hole cutouts in
the bottom flange at the side or back of the cabinet. Insert the screw heads into the alignment
holes FROM THE TOP and rest the panel on the flange. Push the top of the panel until it
rests against the top side or back of the cabinet BELOW THE TOP OF THE FLANGE and
align to the obround holes in the cabinet wall. When in position fasten with 2 #10 screws to
secure panel from the inside of the cabinet.
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 9 of 17

Straight Fillers
Front fillers are offered in standard sizes from about 1” to 6+”. They are also sold in custom sizes
(with an engineering charge). The designation for a front filler is OFLFxx where the xx is the width
of the filler. The front filler design incorporates a small “joggle bend” to provide a proper reveal on
either side adjacent to the cabinets or wall. Rear fillers have straight bends and do not provide a
reveal. The designation for a rear filler is OFLxx where the xx is the width of the filler.
Front fillers are designed to extend to the face of the cabinet door!
1.
Partially install 3 #10 screws in the accessory holes in the front flange of the cabinet(s) for
front fillers and in the side of the back panels for rear fillers.
Align the front filler to the face of the door and slip the keyholes in the filler over the
partially installed screws (Keyhole Alignment Method).Align the rear filler to the back panel
and install the same way as the front filler.
Tighten screws.
2.
3.
Angle Fillers
Angle fillers are offered standard in 90 degree (OAF90 for front, OAR90 for rear) and 45 degree
(OAF45, OAR45) with 4” on either side of the angle. Custom sizes are available (with an
engineering charge).
The front angle fillers are installed the same as straight fillers using the Keyhole Alignment
Method. The rear angle fillers (OARxx) include an angled post with adjustable leg and 2 panels to
fill a corner void where counter top support is required. For rear angle fillers:
1.
2.
Partially install 3 #10 screws in the holes on each side of the angled post.
Partially install 3 #10 screws in the accessory holes on the rear flange of the cabinet(s) or, if
using back panels, in the 3 holes in the side of the back panels installed on the adjacent
cabinets.
Install the panels using the Keyhole Alignment Method described earlier.
3.
Refrigerator Accessory Panels
Depending on the layout, you may require Brown Jordan Outdoor Kitchens accessories to
complete the installation of refrigerators in the outdoor kitchen.
1.
If you are building a freestanding island with Brown Jordan Outdoor Kitchens back
panels, you will need Refrigerator Spacers of the appropriate size to match the
refrigerator’s width (ORS15, ORS24, ORS27). These are screwed to the back panels on
the adjacent cabinets using the Keyhole Alignment Method. The spacer acts as the back
panel behind the refrigerator.
If you are installing two refrigeration appliances (e.g. refrigerator and ice maker or freezer
or beer dispenser) next to each other in a freestanding island installation, most designers
prefer to install a support member between the appliances on which to rest the counter top,
and to provide a better visual appearance. A Box Column (OBX--3 7/8” wide and has two
leveling legs) of the appropriate depth to match the cabinets is designed for this purpose. It
is installed between the two refrigerator spacers at the back using the Keyhole Alignment
Method and creates 2 spaces for the appliances.
2.
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 10 of 17

3.
If you are installing refrigerators against a wall or in a surround or enclosure made of stone,
stucco brick, etc. many installers are choosing to install the Refrigerator Spacers (ORS) to
“define” the refrigerator space more precisely than just installing adjacent cabinets and
leaving a “hole”. The same is true with Box Columns (OBX) where 2 refrigeration devices
are installed next to each other in a surround.
If the refrigerator will be at the end of a cabinet run and you plan to use a stainless side
panel and/or back panels, then in addition to the refrigerator spacer, you will need a
Refrigerator End Panel (ORP--3 7/8” wide and has two leveling legs) of the appropriate
depth. The difference between the ORP and the OBX is that the ORP is completely finished
on one side with access holes on the other side and the OBX is finished on the front and
back with access holes on both sides. The Keyhole Alignment Method is used to screw the
ORP to the refrigerator spacer (ORS) and the spacer to the adjacent cabinet. (See Sample
Layouts Drawing)
If the refrigerator will be on one side of a corner and an OAF (front angle filler) will be
used, an OBX will need to be incorporated into the design along with a special version of
the OAF, the OAF Front Only. In this instance the OAF Front Only will mount in front of
the OBX by aligning the screw holes at the front of the OBX with the holes in the OAF but
at the back of the OAF. Everything else installs as described earlier. (See Sample Layouts
Drawing)
A 4” trim piece (OCT4) is available to finish the inside of a refrigerator space 4” in from the
front. These are used so when the refrigerator is opened the normally unfinished side of a
cabinet is not seen. They are installed using black plastic push rivets that require no tools.
Simply line up the holes in the OCT4 to the accessory holes in the front flange of the cabinet
and push the rivets in.
REINSTALLING DRAWERS
4.
5.
6.
1.
Reinstall drawers by pulling out the slides and putting the drawer on top of the slides. At the
same time, hold one of the slides at the back and push the drawer so it locks into place.
Repeat with the other side. Test drawer by opening and closing. Install bumpers at 4 corners
at the back of the drawer face, if necessary.
Adjust drawer face by loosening and retightening as necessary the 2 or 4 screws on plate at
inside face of drawer.
ADJUSTING CABINET DOORS
2.
Adjust cabinet doors when all appliances, counter top and other finish work is done. To do so earlier
is a waste of time.
1.
2.
The front screw is used to center the door in the opening.
The back screw is used to align the front of the door with the cabinet frame and to secure
the door to the cabinet. Slightly loosen screw (while holding the door!) and slide door in
and out until aligned. Retighten.
Loosen the hinge plate mounting screws and slide hinges up or down for further adjustment
if necessary. Retighten when aligned.
3.
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 11 of 17

OAR90
ORP Angle
Bracket
ORS
Cabinet
attaches here
OAF90
OCT4
How to fill corner void and
place fridge at end of run
OBX ORS
ORP
Space for
fridge
OAF90
Front only
Space for
fridge
How to place fridge
next to corner
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 12 of 17

TOE KICK, OTHER ACCESSORIES
Black toe kick is sold in 8’ (96”) lengths, 4 3/8” high. It is aluminum, 3mm thick with black
on the front and white on the back. Cut toe kick to appropriate length. A saw suitable for
smooth cutting plywood (lots of teeth) will work. Lay the toe kick on the ground in position
in front of the cabinets. Remove the covering from the back of the Velcro strip on the clip
holder. Install toe kick clip holders (supplied with toe kick) on the back of the toe kick
where they line up with cabinet legs. Slide clip onto the toe kick clip holders. Snap toe kick
to front legs. Use as few or as many clips as necessary. Install in the same manner on side
and back if side panels and back panels are installed. Toe kick can be removed for cleaning
under the cabinets if desired.
1.
2.
Stainless toe kick is sold in either 8’ (96”) lengths, 4 3/8” high or by the linear inch, same
height. The stainless is glued and attached with tabs to the standard aluminum toe kick
(acting as a structural backer). Install with the clips as described in (1) above.
If a raised counter is desired for a bar-height seating area, install 41” high piers (OCP41 or
OCP41E with electrical box cutout) to hold up the raised countertop. They are affixed by
installing the “tongue” in the slot in the pier and putting it over the rear top rail (stretcher) of
the cabinet under the counter top. Then install and tighten 3 #10 screws against, not into (no
holes), the rear top rail. Install the counter top over the tongue. Install the tubular spans in
the slots in the piers to help support the bar top.
Install locally supplied countertop.
Install appliances per each appliance manufacturer’s installation instructions.
Align doors and drawers. Enjoy!
3.
4.
5.
6.
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 13 of 17

Tighten 3
#10 Screws
Top Brkt fits
over column to
allow for a large
gluing surface
Optional
Electric
Cutout
Bracket adjusts
in and out for
different thickness
Adjustable
Feet
OCP Instructions
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 14 of 17

Side Panel (OSP) & Back Panel (OBP) Installation
Step 2
From inside of cabinet locate 2 holes that
align with panel bend and install 2 #10 screws.
This will hold the panel in place. The panel
will be under the top lip of the cabinet!
This is important if you ever have to replace
the panel in the future.
Step 1
Place Side Panel on top of cabinet lip. The
screw heads on bottom of panel are for
alignment only and will fall into the 2 large holes
in cabinet lip. This will hold the bottom in place.
These same steps apply to the Rear Panels. Panel
installation should take no longer than 30 seconds
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 15 of 17

CARE AND CLEANING
Carefully remove protective plastic peel coat from each stainless steel surface and drawer
sides. Clean stainless with stainless steel cleaner in direction of grain. Rubbing across the
grain direction may produce minor scratches. Some good cleaners are Weiman, Stainless
Steel Magic and Sheila Shine.
In a salt air environment, a slightly more oily cleaner like Sheila Shine will protect better
against oxidation, pitting or slight surface rust. Cleaning the surfaces periodically will
protect the finish for many years. In a heavy salt area, you will have to clean more
frequently as salt breaks down into highly corrosive chlorine that will attack the metal.
Surface corrosion will not affect performance of the product, but will affect the look.
The cabinet’s “working surfaces” are constructed from stainless steel with no grain. It is
somewhat more scratch resistant but equal in durability to the grained surfaces. Use the
same stainless cleaner as on the rest of the surfaces.
LOW MAINTENANCE FINISHES
1.
2.
3.
To address the public’s resistance to doing maintenance, Brown Jordan Outdoor Kitchens has
developed several low to no maintenance finishes. Powder coat in different styles completely seals
the stainless from the environment (salt, chlorine and muriatic acid) eliminating the worry of
pitting and surface rust. The painted finishes can be cleaned with water or other household cleaner
only if needed. Available on all exterior surfaces (doors, drawer fronts, panels or trim) or the
complete cabinet.
1.
2.
Protect-A-Coat—Clear coat retains the look of stainless with a slightly “wet” look.
Painted Finishes—Powder coat colors are used to achieve a designer look or to blend in with
the environment.
Wood Finishes—We use a powder coat painting process that transfers wood grain
permanently into an exterior grade powder coat base coat to create tremendously realistic
wood finishes on stainless doors and drawers. Use the wood finish on accent doors and
panels, or make the kitchen all with the wood look.
3.
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
Phone [phone], fax [phone]
Page 16 of 17

Brown Jordan Outdoor Kitchens Cabinetry Limited Lifetime Warranty
Brown Jordan Outdoor Kitchens hereby warrants to the original consumer purchaser that its
outdoor cabinets and related products and accessories are free from manufacturing defects and
workmanship for the useful lifetime of the product. This warranty is not transferable and is for
residential applications only. This warranty does not apply in the case of normal wear and tear,
accidental misuse, abuse, or negligence, product modification, improper storage or improper
installation. This warranty is expressly limited to repair or replacement of the defective part at the
discretion of Brown Jordan Outdoor Kitchens, and does not include expenses incurred in the
removal, shipment or installation for removal or replacement. This warranty applies only to
cabinets or related products purchased through an authorized Brown Jordan Outdoor Kitchens
dealer. This warranty is in lieu of all other implied or expressed warranties. Surface corrosion and
discoloration is not covered under warranty but can be minimized or eliminated with care and
cleaning.
The drawer slides were chosen for strength and durability with use. They have been treated to
withstand the elements, but their warranty is limited to two (2) years. Replacements are available
if necessary.
Brown Jordan Outdoor Kitchens reserves the right to make changes in design, construction
materials and prices as conditions require and as improvements are developed, without obligation
to incorporate such changes in cabinetry or related products previously manufactured by Brown
Jordan Outdoor Kitchens.
All implied warranties, including the warranties of merchantability and of fitness for a particular purpose,
are limited in duration to the period of the express warranty stated above. In no event shall Brown Jordan
Outdoor Kitchens be liable for incidental or consequential damage.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitations and exclusion may not apply to some purchasers.
This warranty gives you specific legal rights. You may have other rights, which vary from state to
state.
Claims –all claims for defective cabinets or related products must be submitted to Brown Jordan
Outdoor Kitchens in writing and must specify the defects alleged to be present. Brown Jordan
Outdoor Kitchens will, at its discretion, either repair or replace any defective cabinets or related
products.
Stainless steel surfaces can be scratched and/or dented during normal use or installation. These
marks are not covered as defective material or workmanship. Keep in mind that stainless steel
needs periodic maintenance; more in harsh climates. All complaints about defective surface finishes
must be inspected by an authorized representative of Brown Jordan Outdoor Kitchens prior to
installation. Brown Jordan Outdoor Kitchens will not be responsible for any expense involved in
removing or reinstalling cabinetry with a defective finish. Brown Jordan Outdoor Kitchens
reserves the option of either approving field repair or returning the cabinetry or component to the
factory for correction. If a field repair is possible, an accurate estimate of the cost must be obtained.
No action can be taken without Brown Jordan Outdoor Kitchen’s authorization.
Brown Jordan Outdoor Kitchens
One Grand Street, Wallingford, CT 06492
phone [phone], fax [phone]
Page 17 of 17