Brown Wood Designs of distinction Shoin User manual

• TOP 12” DISK
• TURNED LEG WITH DOWEL CENTER
• BOTTOM 12” DISK
• 24” DISK
INCLUDED IN PACKAGE:
WOOD PIECES: (1 EACH)
• ¼” X 1” WOODEN DOWELS ( X 4 )
UNTIL DISK STOPS AT TOP OF LEG.
DOWELS AND PUSH TOGETHER UNTIL DISK STOPS AT
BOTTOM OF LEG
"PROVIDED FOR USE IN TABLE TOP PROVIDED
2-C) INSERT SCREW THROUGH CENTER HOLE OF DISK
AND INTO THE THREADED INSERT IN THE LEG AND TIGHTEN.
1-B) ALIGN AND PUSH 12" DISK ONTO DOWELS
STEP 2 - BOTTOM ASSEMBLY
STEP 1 - TOP ASSEMBLY
BY CUSTOMER"
THE PRE DRILLED HOLES IN THE BOTTOM OF LEG
1-A) INSERT ¼” X 1” WOODEN DOWELS ( X 2 ) INTO
THE PRE DRILLED HOLES IN THE TOP OF LEG
THE THREADED INSERT IN THE LEG AND TIGHTEN.
1-C) INSERT SCREW THROUGH DISK AND INTO
HARDWARE:
• 1 ½” FLAT HEAD SCREW ½-13 THREAD ( X 2 )
• 1 ½” FLAD HEAD SCREW 3/8-16 THREAD ( X 8 )
• 3/8-16 THREADED INSERTS ( X 4 )
2-B) ALIGN AND PUSH 12" BOTTOM DISK ONTO THE TWO
2-A) INSERT ¼” X 1” WOODEN DOWELS ( X 2 ) INTO
DATE:
SHOIN TABLE KIT ASSEMBLY INSTRUCTIONS PAGE 1
11/20/2018
TOP 12" DISK
1-B
1-A
IN THE CENTER
ONE GOING DOWN
ON THE BOTTOM
TOP PLATE HAS
FOUR COUNTER
SUNK HOLES
GOING UP AND
RADIUS EDGE
1-C
1-C
1-B
1-A
2-A
BOTTOM
INSERTS
2-C DISK WITH
THREADED
2-A
ROUNDED
BOTTOM
TOP
EDGE
EDGES
ROUNDED

STEP 2 - BOTTOM ASSEMBLY
CONTINUED STEP 3 - PREP TOP BY OTHERS
WITH THREADED INSERTS.
2-D ALIGN THE COUNTER SUNK HOLES ON THE
24" BOTTOM DISK WITH THE 12" BOTTOM DISK
2-E INSERT THE SCREWS THROUGH THE HOLES
IN THE 24" BOTTOM DISK AND TIGHTEN THEM
INTO THE INSERTS ON THE BOTTOM OF THE12"
DISK.
3-A FOR EASE, PLACE THE TOP BY OTHERS WITH TOP DOWN ON
A WORKBENCH AND POSITION THE ASSEMBLED TABLE KIT WITH
TOP DOWN AND REST ON THE BOTTOM FACE OF THE TOP.
3-B ONCE THE TABLE KIT HAS BEEN CENTERED ON THE BOTTOM
SIDE OF THE TOP BY OTHERS TAKE A PENCIL AND MARK THE
LOCATIONS OF EACH OF THE FOUR COUNTERSUNK HOLES ONTO
THE BOTTOM SIDE OF THE TOP.
3-C USING THE LOCATIONS FROM THE MARKED HOLES
ON THE PREVIOUS STEP, DRILL 4 SHALLOW HOLES USING
A 15/32" +/- DRILL BIT (TEST IN A SCRAP PIECE FIRST TO VERIFY
A TIGHT FIT). DRILL DOWN ENOUGH TO ACCEPT THE
THREADED INSERTS (APROXIMATELY 9/16" DEEP).
NOTE: USE A DRILL STOP OR BLOCK SPACER TO AVOID
GOING ALL THE WAY THROUGH THE TOP.
TABLE SHOWN
UPSIDE DOWN
STEP 4 - INSTALL TOP BY OTHERS
ONTO THE TABLE LEG KIT
4-A ALIGN TOP BY OTHERS WITH THE COUNTERSUNK
HOLES ON THE TOP 12" DISK OF TABLE KIT.
4-B ONCE ALIGNED, SCREW THE FLAT HEAD SCREWS
INTO THE THREADED INSERTS THAT WERE INSTALLED
IN STEP 3-D
3-D USING A LARGE REGULAR SCREWDRIVER SCREW
THE THREADED INSERTS INTO THE HOLES THAT WERE
JUST MADE IN THE TOP BY OTHERS.
BOTTOM SIDE OF TOP
3-C
4-A
TABLE TOP PROVIDED BY OTHERS
SHOIN TABLE KIT ASSEMBLY INSTRUCTIONS PAGE 2
DATE: 11/20/2018
COMPLETED ASSEMBLY
BOTTOM SIDE
OF TOP
BY OTHERS
3-B
3-A
3-D DRILL 4 HOLES
AT APROXIMATELY
15/32" DIA. AND
9/16" DEEP. (VERIFY
ON TEST PIECE FOR
SNUG FIT WITH THE
THREADED INSERTS
PROVIDED IN KIT.
BOTTOM
TOP
THREADED
INSERTS
2-D
2-E