BT Security PL-RLV User manual

User Manual
PL-RLV
Please read this manual carefully before using this product , keep it safe for future
use. We reserve the right to modify the specification in this manual at any time
without notice.
GND NO COM NC 12V S2 S1 GND
POWER RISER
BUS BUS
1
2
3
SYSTEM
2-WIRE
PL-RLV
Relay Actuator

DIP
1 2 3
12 3
ON
Lock Control
Jumper
1
2
3
NC
COM
NO
GND
12V
S2
S1
GND
POWER
BUS
DIP
GND NO COM NC 12V S2 S1 GND
POWER BUS BUS RISER
1
2
3
-1-
1. About the PL-RLV Unit
SY STEM
2-WIRE
PL-RLV
The relay actuator PL-RLV is an accessory device designed for 2-wire
systems to enable control of door locks . Features as follows:
Note that the factory default is lock control mode.
Allows to opening of gates, door locks .
Supports high power-consumption locks using an external PSU.
Configurable timing for unlock output.
Supports exit button when in lock control mode to release the lock(
timed).
22
12V: +12V power output for fail secure strike, max 12vdc 450mA.
S2: The port for unlock DIP settings
S1: Exit button contact input. Short this contact to GND to unlock.
GND: The common Ground of the other 3 contacts: S1, S2 and +12V.
2. Parts and Name

GND NO COM NC 12V S2 S1 GND
POWER BUS BUS RISER
1
2
3
DIN Rail Mounting
SY STEM
PL-RLV2-WIRE
3. Unit Mounting
4. How to set the unlock delay time
The lock time have: 0s, 5s, 10, 15s for your optional. It's better that setting up 0s
for Electronic lock ; 5-15s for E-magnetic locks or other kinds of locks.
DIP Switch
2-OFF ,3-OFF
Bit State Optional Unlock delay time(Second)
2-ON, 3-OFF
2-OFF ,3-ON
2-ON, 3-ON
1s
5s
10s
15s
2 3
ON
2 3
ON
2 3
ON
2 3
ON
NC: Normally-closed contact .
COM: Common contact of the unlock.
NO: Normally-open contact.
Lock Control Jumper: To select the lock type: see section 4,5.
POWER: LED Indicator, on when connected to live Bus.
Bus: Connection for the 2 wire bus line, no polarity.
DIP :Used for setting the address of the RLV and configuring work mode.
-2-

DIP settings for lock.
5. DIP Switch Setting
The DIP switch on the rear of the RLV is used t o s et t he a ddress. This setting
need according the DIP switch and S2 port to program.Please refer to the
following tab for more detailed information regarding the DIP and S2 settings.
-3-
DIP
1-OFF
Bit State Optional S2 State Optional
1-ON
1-OFF
1-ON
S2 won't connect to GND
S2 connects to GND with cable
S2 connects to GND with cable
Applies to door
station 1 & lock 1
S2 won't connect to GND
Applies to door
station 2 & lock 2
Applies to door
station 3 & lock 3
Applies to door
station 4 & lock 4
1
ON
1
ON
1
ON
1
ON
Description
12V
S2
S1
GND
12V
S2
S1
GND
12V
S2
S1
GND
12V
S2
S1
GND

Note:
Jumper position in 1-2
1 2 3
GND NO COM NC 12V S2 S1 GND
E-lock Exit Button *
+
-
PL-RLV
PL-RLV connect lock
5.1 Internally powered lock connection - Suitable for Power-on-
to-unlock/Fail Safe strikes.
PL-RLV controls the a second lock for door station 1
1.When PL-RLV is connected to an
E-magnetic lock, the jumper position is
1-2.And internal power supply is 12V out.
2.When PL-RLV is connected to an
Electronic lock, the jumper position
is 2-3.And internal power supply is 12V out.
Exit Button
GND NO COM NC 12V S2 S1 GND
E-lock
AC~
1# Camera
(Device Address:0)
NO
POWER
GND COM NC 12V S2 S1 GND
BUS RISER
1
2
3
-
+
12 3
ON
DIP
CDV-RLC 2-WIRE SYSTEM
monitor
BUS
-4-

GND NO COM NC 12V S2 S1 GND
E-lock Exit Button
*
POWER
SUPPLY
+
PL-RLV
5 .2 External Power Supply powered lock connection
PL-RLV controling the second lock of door
A: Power-on-to-unlock(fail-secure) lock :
PL-RLV lock connection:
Exit Button
12V S2 S1 GND
GND NO COM NC
Adaptor
for the lock
E-lock
-
+
NO
POWER BUS
GND COM NC 12V S2 S1 GND
BUS RISER
1
2
3
12 3
ON
DIP
PL-RLV
SYSTEM
2-WIRE
Station 1
1# Camera
(Device Address:0)
monitor
AC~
-5-
If need the external power supply to the lock,the jumper must be taken
off before connecting.
-

GND NO COM NC 12V S2 S1 GND
EM- LOCK Exit Button
*
POWER
SUPPLY
+
PL-RLV
B: Power-off-to-unlock(fail-safe) lock:
PL-RLV controling the second lock of door station 1
PL-RLV lock connection:
Exit Button
EM-lock
-
+
External PSU
for the lock
12V S2 S1 GND
GND NO COM NC
NO
POWER BUS
GND COM NC 12V S2 S1 GND
BUS RISER
1
2
3
12 3
ON
DIP
PL-RLV
SYSTEM
2-WIRE
1# Camera
(Device Address:0)
monitor
AC~
-6-
-

6. Connecting 2 x PL-RLVs
In a single svstem, two PL-RLV units can be connected to control a gate/lock and a
light if required
POWER
GND NO COM NC 12V S2 S1 GND
Exit Button
POWER
GND NO COM NC 12V S2 S1 GND
Adaptor for the lock
E-lock
Safety Type: power-on to open
power-off to lock
2 3
1
ON
DIP
2 3
1
ON
DIP
RLV
RLV
1# Camera
(Device Address:0)
monitor
AC~
-7-
7. Specification
•Power Supply : DC24V;
•Unlocking Time: 1~15s(Default 1s);
•Lock Power supply: 12Vdc, 450mA(Internal Power);
•Working Temperature: -100C~+400C;
•Dimension: 89(H)×71(W)×45(D)mm.
Note: PL-RLV only connect on the Bus line, if multiple doors need to
connect on the video distributor.