BT Tele 300B User manual

BT Tele 300B
Item: 026578
DigAlertTM Test Telephone with Loud Speaker
compatibleADSL
Ground-start lines
ELR: Earth Loop Recall
Field repair
Line-cord changing
Line-cord storage
Impact
On units fitted with optional third wire (item 315628):
On units fitted with optional third wire (item 315628):
(item 315629)
connect green wire to ground, press
TALK momentarily and check for dial tone. Ground start is then automatic and the green wire
can be left connected to ground, without affecting the call.
while in TALK mode on a looped line
and with the green wire to ground, press PULSE momentarily and check for second dial
tone.
Field repairs are limited to replacing line cords (with approved types), replacing belt clips, and
replacing batteries. Attempting any repair beyond this at field level is liable to damage the
instrument and will invalidate the manufacturers warranty. Check your company policy before
considering any repair. Although limited field repair may be possible your company may have a
policy of centralised repair.
Remove the three hatch cover screws. Replace the cord by loosening the
terminal screws. Connect a new, standard cord as per the diagram. Tighten the screws firmly
but do not use excessive force. Make sure the battery cover sits down properly before securing
it with the 3 screws.
Wrap the line cord loosely around the handle or preferably make a few loops and pass them
through the belt clip.
Tele300B is highly impact resistant. Even if dropped from a great height onto concrete
Tele300B should survive without permanent damage. In the event that the gasket seal should
bulge out on impact it is usually possible to gently ease it back into position with a blunt tool. Do
not attempt to open the case to make a repair nor should any force be used or the gasket may
split. If a simple local fix is not possible it should be returned for repair.
Please note that the waterproof seal integrity can be damaged by a high impact. If in doubt,
please have your unit checked. Use of the unit while the seals are damaged may invalidate the
warranty.
t
p
Care and repair
Do not open the case.
Black / Tip / +Ve
Green
/ Earth
Red / Ring / -Ve
Plug-in Adaptors:
Adaptor Test 3B I/C 003965
Adaptor Test 4A I/C 003043
Tele 300B User Guide part n° 1201-03-2505 issue 9, 09/06
USER GUIDE
range
Additional Information:
http://networks.intra.bt.com/cimradio/es/es_test/eppm_04-99/project_04-99.html
i
Tempo Europe Ltd.
Suite 8, Brecon House, William Brown Close,
Llantarnam Park, Cwmbran NP44 3AB, U.K.
(
4
[phone]
[phone]
[email protected]
www.tempo.textron.com

ü

t
m
M
TALK MODE
MONITOR MODE
MUTE
Press to go off-hook.
Adouble beep is heard and the mode LED flashes .
Press to go back on-hook. The mode LED then flashes .
: if Tele300B is connected to an overvoltage or a digital signal,
then Tele300B does not loop the line and sounds an alarm.
Connect Tele300B to the line.
Press and release to go off-hook. Thanks to , there are four
different cases:
1\ a digital signal is present: is heard, Tele300B locks out and
does not loop the line. To override this alarm, hold down the key.
2\ a high DC level is present (>116V±4V): is heard,
Tele300B locks out and does not loop the line. This alarm may not be
overridden.
3\ a dc level between 76V(±4V) and 116V(±4V) is present:
is heard, the mode LED flashes , Tele300B locks out and
does not loop the line. To override this alarm, press again.
4\ no alarm (i.e. no digital signal nor high DC present): Tele300B goes off-hook
and loops the line.
When connected to normal DC, it is possible to override the digital detection
lock-out by pressing and holding for more than 6 seconds and until the
override tones have stopped. This can be particularly useful on a faulty line
being highly imbalanced.
Press . The mode LED flashes . Press again
to switch off Tele300B.
In order to extend its battery life, Monitor is automatically switched off after 20
minutes, if connected to a powered line, and 5 minutes after disconnection. An
audible signal is heard on timing out.
Press and release to cut off transmission during a call. Press again to
talk.
300B
Press to activate the speaker function. If is pressed
while Tele300B is off, then Loud-speaker Monitor is automatically activated.
Press and release to select the high setting, press again to return to
the normal setting.
In TALK mode, receive only is possible while in speaker mode.
After disconnection from the line for more than 5 minutes, Tele300B
automatically switches off and the time-out tone is heard.
t
m
t
t
t
t
mm
M
ss
v
TALK
RED
MONITOR GREEN
TALK
a two tone alarm
TALK
a single tone alarm
a single tone alarm
RED and GREEN
TALK
Digital signal detection OVERRIDE
TALK
MONITOR GREEN MONITOR
MUTE
SPKR SPKR
VOL
Press and observe the polarity LED.
LED: red lead is connected toA(+Ve).
LED: red lead is connected to B(-Ve).
During this test, Tele remains high impedance and will not interfere with
data or speech calls..
PLEASE NOTE
Volume adjustment:
AUTOMATIC PROTECTION OF DIGITAL LINES:
POL: POLARITY TEST
SPKR: SPEAKER MODE
(high impedance).
POL
RED
GREEN
P
s
P
DigAlertTM
DigAlertTM
l
f
Sr
p
LNR/PAUSE: Last Number Redial and Pause
FLASH
STO MEM Storing a number in memory
Dialling a number from a memory location.
PULSE Dialing
Mixed Pulse and Tone dialling
LOW BATTERY
INSTALLING or REPLACING THE BATTERY
LNR/PAUSE
LNR/PAUSE
LNR/PAUSE
FLASH
STO MEM
STO
MEM
PULSE
you are advised to
replace the battery as soon as possible
Press immediately after off-hook to redial the previous
number dialled. In STORE mode (see below) press to
insert a Pause in a memory. If within the first 5 entries, this inserts a 2 second
pause in the dialling out string, if not, then it halts the dialling. Press
to resume.
Atimed line break is generated when this button is pressed.
:
There are ten memory locations, one under each of the dialling digits.
While connected to a line and in TALK mode:
Press to enter STORE mode, Press and a location (0-9).
Enter the telephone number to be stored then press to store.
The number is stored under the button chosen. ln memory you may also store
,#, Flash or Pause. These will be redialled as they were entered.
While connected to a line and in TALK mode:
Press . Press the location digit 0-9.
The stored number under that button will be redialled.
With the DigAlert™ connected to a live line, press before
selecting Talk mode. This is confirmed by a single high beep. Dialling mode
will automatically revert to Tone when the line is disconnected or if the
Tele300B is switched off.
Select Pulse mode as above and dial the Pulse digits. Press (Tone) then dial
the Tone digits (the star will not be dialled out). This will be stored in the Last
Number Redial memory ( ) as dialled. Redialling will be mixed mode if in
Pulse mode when redial is attempted. If tone mode is selected all digits
will be dialled in Tone including the star.
A red LED at the centre of the keypad starts to flash RED when the battery
needs replacing. Also, at each mode change of the Tele300B, a low battery
tone will be heard. Once the low battery LED is on, Tele300B will keep on
working to its specification for a couple of hours, but
.
Remove the three hatch cover screws as shown below. Unclip the battery and
replace it with a 9V alkaline battery. Make the change within one minute if you
want to retain your memory contents.
Disconnect from the line and press Monitor button to extinguish the Green
(Mode) LED.
To cure it, disconnect the battery for at
least 2 minutes and short the terminals together for a few seconds (when
battery not fitted). Replace the hatch cover ensuring that the line cord is
correctly routed. Tighten the screws firmly but do not use excessive force.
l
l
l
f
t
Sr
S
*f l
t
r
p
t
*
l
l
m
It is very important to ensure that Tele300B is off when replacing a battery
(No LED lit).
If you do not do this, when the new battery is fitted, the test-
telephone may not restart correctly.
?
1
2
3
4
5
6
7
8 9
0
#
Red: Talk Mode.
Green: Monitor mode.
Red lead polarity:
Green = B(-Ve).
= A (+Ve).Red
Replace
Battery
PULSE FLASH VOL
MEMLNR/PAUSE STO POL
SPKR
TONE
TALK MONITOR MUTE
Warning! When in Loudspeaker mode,
hold loudspeaker more than 30cm (1 foot)
from your ear.
Misuse can result in hearing damage.