DESCRIPTION OF FUNCTIONS
Inserting the handle part into the lance part (fig. 4)
•If necessary, remove the plug of the charger from the
handle part before inserting it in the lance part.
•Insert the front of the handle part into the top of the lance
part.
•Slowly slide the handle part until it clicks into the lance
part.
•Do not apply great force when inserting the handle part. If
the handle part cannot be easily pushed in, it is not
inserted properly.
•Check that the parts are locked in place.
Unlocking the handle part (fig. 5)
•Press the release button (F).
•Carefully pull the handle part out of the lance part.
•Do not apply great force when pulling off the handle part. If
the handle part cannot be pushed out easily, it has not
been released properly.
Activating the product (fig. 6)
• Gently press the ON button (H) and immediately release.
After releasing the ON button, the system starts up. After 3
seconds, the product is ready for use.
•The LED (G) flashes green/red to indicate the battery
status.
•After 10 seconds, the LED stops displaying the battery
status and switches off.
Function LED
•Green flashing the product is ready for use.
•Blue the product is active.
•Red the product needs to be charged.
•Orange safety mode. Wait until the orange
LED goes out (max. 1 min). The
product is ready to use again.
Battery status
•Flashing 1x per sec. green > 30% charge
•Flashing 2x per sec. green 10 - 30% charge
•Flashing red Product must be charged
Charging the product (fig. 7)
•Carefully remove the handle part from the lance part. The
charging connector (J) becomes visible at the bottom of
the handle part.
•Insert the plug of the supplied charger into the charging
connector of the handle part.
•Insert the charger into the socket.
•LED on the charger turns red. The product is charging.
•LED on the charger turns green. The battery in the product
is full and the handle part is ready for use.
•Remove the charger plug from the handle part as soon as
it is fully charged.
Cleaning process toilet (fig. 2 and 3)
•Place the front of the product's lance in the toilet water and
switch on the product.
•You will hear a buzzing sound, this is the sign that cleaning
has started. The ultrasonic element emanates from the
front and sides, cleaning the toilet.
•During cleaning, gently move the product through the
siphon, aiming at the walls and dirt.
•After cleaning, flush the toilet while switching the product
on again and moving it around in the water. You are now
cleaning just above the water line and also cleaning the
product at the same time.
Notes
A new handle part or a handle part that has not been used
for a long time may sometimes not be fully charged until you
have fully discharged and recharged it a few times.
OPERATION
Using the product
Standard cleaning (30 seconds)
•Flush the toilet if there is loose dirt in the siphon.
•Briefly press the ON button to activate the product. The
product is ready for use when the LED flashes green.
•Place the front of the product's lance in the toilet water.
•Briefly press the ON button again to start the standard
cleaning. Cleaning has started when the LED turns blue.
•The product automatically switches off after 30 sec or
stops if you briefly press the ON button again.
Manual cleaning (max. 1 minute)
•Flush the toilet if there is loose dirt in the siphon.
•Briefly press the ON button to activate the product. The
product is ready for use when the LED flashes green.
•Place the front of the lance of the product in the toilet
water.
• Press and hold the ON button to start manual cleaning.
Cleaning has started when the LED turns blue.
•The product cleans as long as the button is pressed and
stops as soon as the ON button is released.
•The product switches off automatically after 1 minute and
can be used again after a few seconds.
Caution
•For stubborn soiling, you may need to repeat the cleaning
process. Old or stubborn soiling may not disappear in one
cleaning.
•With significant soiling of the toilet, additional soiling may
come off when flushing after cleaning and be visible in the
siphon.
•The product needs to break in and will clean better the
more often it is used.
MAINTENANCE
Periodic cleaning product
•After cleaning a toilet with the product, flush the toilet while
switching the product on again and moving it around in the
water. You are now cleaning the product itself.
•Wipe the product while it is assembled (handle part locked
into the lance part) with a damp cloth.
•From the top of the notches on the white lance part to the
cleaning ultrasonic element, it can be wet cleaned.
