BubblyNet C-IX8-24-DS00 User manual

BubblyNet - 615 Drew St., Clearwater, FL 33755 •Ph 727.316.5319 •Fx: 727.683.9720 •The manufacturer reserves the right to change or modify the design, dimensions
and specications at any time without notice. The manufacturer accepts no liability for consequential damage which is occasioned to the user based on the data provided.
bubblynet.com • 727.316.5319
10.13.2023
Specications
•Input Voltage Range - 12-24 VDC
•No-Load Input Current - 30 mA
•Aux-Relay Control Output - 12-24 VDC, same as input
•Aux-Sensor Input Voltage - Max 24 VDC
•Ambient Temperature, ta - -13 to 113°F(-25 to 45°C)
•Max Relative Humidity - 0 to 80%, non-cond.
•Wire Range, Solid & Standard - 0.5-1.5 mm, 14-22 AWG
•Wire Strip Length - .25” (6-7 mm)
•Dimensions - 2.2” x 1.2” x 0.7” (72.6 x 30.0 x 18.0 mm)
•Weight: 0.8 oz (23 g)
Certications
DMX-IN Controller | Model: C-IX8-24-DS00
Installation
Connect a Class 2 power supply with 12-24 VDC output
voltage to the input connector of the DMX-IN Controller.
Make sure not to use a constant current LED driver and
that the cable polarity is correct.
The product can be installed outside of a junction box.
Make sure to comply with National Electric Code in
installation and when selecting installation wires.
Description
The DMX-IN Controller can monitor up to eight DMX
channels (slots) which can be configured to control upto 8
different zones in the BubblyNet network irrespective of the
application. The DMX is powered by a 12-24 VDC Class 2
power supply and provides a relay output, and sensor input.
200ft
100ft
70ft
60ft
50ft
Typical maximum distance:
OuOutdoor (line of sight):
Indoor (through building material):
Glass:
Drywall:
Cinderblock:
Brick:
Concrete + rebar 0ft
Devices with external antenna should have the antenna
outside any metal box and away from metal surfaces as
metal reduces connectivity.
For design purposes a 60ft. maximum distance is
appropriate for most installations.
Different BubblyNet enabled products can be used from
a simple one luminaire direct control to a complete and
full featured light control system where thousands of units
form automatically an intelligent mesh network. The DMX-
IN Controller can be controlled with the BubblyNet App
which can be downloaded free of charge from Apple App
Store and Google Play Store. Relay output and sensor
input is included.
BubblyNet uses mesh network technology so each DMX
-IN Controller acts also as a repeater. When testing the
network, it is important to test that each unit can be
controlled from any point of the network covered area.
Connectivity
Devices are repeaters for other devices and should be
installed within a certain maximum distance from each
other.

BubblyNet - 615 Drew St., Clearwater, FL 33755 •Ph 727.316.5319 •Fx: 727.683.9720 •The manufacturer reserves the right to change or modify the design, dimensions
and specications at any time without notice. The manufacturer accepts no liability for consequential damage which is occasioned to the user based on the data provided.
Range
BubblyNet uses mesh network technology so each DMX
Input Controller acts also as a repeater. When testing
the network, it is important to test that each unit can be
controlled from any point of the network covered area.
Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try
to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement or Canada
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment is exempt from the routine RF exposure evaluation requirements of RSS-102. This equipment should be
installed and operated with a minimum distance of 20 cm between the antenna and the user or bystanders.
8 Channel DMX
INPUT 12-24 VDC, 30mA
Use Class 2 Power Supply
+
-
To the Mesh
12 - 24VDC
PSU DMX
CONSOLE
Line in
Neutral in
Red
Black
Optional Accessory
from BubblyNet* or Others
110-277V
+
-
Relay OUTPUT: 12-24VDC
Max 100mA
DMX IN +
DMX IN -
RETURN
RELAY
SENSOR
Input Power
*A-T03-12-17-DS00
Red
Orange
Black
Green
Purple
The relay must be protected against inductive over voltage spikes, ie. it must have a yback diode.
Do not connect a typical PCB relay without the diode.
*Illustration is for example purposes only. Manufacturers vary depending on technical requirements of the light.*
bubblynet.com • 727.316.5319
10.13.2023