BuckMaster Blue Ridge Bent Back Glider User manual

Blue Ridge Bent Back Glider
Instruction Manual
P/N: FF-BRSG
Buck Stove, New Buck Corp |200 Ethan Allen Dr, Spruce Pine, North Carolina
28777, United States | [phone] | www.buckstove.com

Included Hardware
*Hardware without piece count comes preinstalled
2.5in Bolt
4PCS
3in Bolt
2PCS
3.5in Bolt
4PCS
Washer
18PCS
Nut
10PCS 1.25in Screw
2 in
Screw
8PCS
1 in
Screw
A B
C D E
F
G N

Included Parts
Arm/Leg Assembly
Back Assembly
Seat Assembly
Rear Cover Strip
Glide Assembly
Front/Rear Brace
H I J
K L M

Required Tools
7/16
Socket Wrench
1/2
Socket
7/16
Wrench
1/2
Wrench
#2 Square Bit

Assembly Instructions
Step 1
Unscrew the loosely attached
1.25 in(F) & 1 in(N) screws,
and remove the rear cover
strip (K) and place aside for
final assembly.
Step 2
Begin the assembly process
by placing the glider in the
orientation shown to the right,
with the back (I) and seat
assembly (J) on their side.

Step 3
Align the holes on the arm
assembly (H) with the holes
going through the back (I)
and seat assemblies(J).
Step 4
Insert the 3.5 inch bolt (C)
through a washer (D) and
into the leg/arm (H), back (I)
and seat (J) assemblies.

Step 5
Insert the 2.5 inch bolt (A)
through a washer (D) and
into the leg/arm (H) and seat
(J) assemblies.
Step 6
On the back side of the bolts
(A & C) that were inserted
through the seat (J), place a
washer and then thread a nut
onto all of the bolts placed in
steps 3-4. Tighten with 7/16
socket and wrench.
Step 7
Place the 3 inch bolt (B)
through the leg/arm assembly
(H) and the back assembly(I).

Step 8
On the back side of the bolt
placed in step 6 (B), place a
washer (D) and then thread a
nut (E) onto the bolt. Tighten
with a 7/16 socket and
wrench.
Step 9
Repeat steps 1-7 for other
leg/arm assembly (H) of
chair.
Step 10
Place the glider in the
orientation shown to the right,
with the glide assembly (L)
underneath.

Step 11
Remove the 3 washers, bolt
and nut which is assembled
through the bracket on the
glide assembly (L). Then
place the bolt through the
composite with a washer on
either side. Slide it though the
bracket and place a washer
and thread the nut onto the
end of the bolt. Tighten til
snug with ½ in socket and
wrench.
Step 12
Repeat step 11 with the rear
bracket on the glide
assembly (L).

Step 13
Repeat steps 11 & 12 for
both sides of the glider, the
glide assembly should be
attched at 4 corners with the
brackets, and the glider
should swing freely.
Step 14
Align the predrilled holes with
the rear brace(M) and screw
two of the 2 inch(G) screws
through the holes and into
the brace.

Step 15
Repeat step 14 on both sides
of the brace to securely
fixture it into place between
the two arm/leg(H)
assemblies.
Step 16
Attach the front brace (M) in
the same manner as the rear
using the predrilled holes and
included hardware.

Step 17
Align the rear cover strip (K)
with the predrilled holes on
the back and seat assemblies
(I & J).
Step 18
Reattach the rear cover strip
removed in Step 1, (K) to the
back and seat assemblies (I
& J) using the provided 1.25
inch (F) and 1 inch screws
(N). The screws are a #2
Square bit.