BuckMaster Blue Ridge Bent Back Rocker FF-BRRO User manual

Blue Ridge Bent Back Rocker
Instruction Manual
P/N: FF-BRRO
Buck Stove, New Buck Corp |200 Ethan Allen Dr, Spruce Pine, North Carolina
28777, United States | [phone] | www.buckstove.com

Included Parts
*Hardware without piece count comes preinstalled (F, G[1], K)
2.5in Bolt
4PCS
3in Bolt
2PCS
3.5in Bolt
4PCS
Washer
18PCS
Nut
10PCS
1.25in
Screw
1.625in
Screw
8PCS
Left/Right Leg/Arm
Assembly
2PCS
Back
Assembly
1PCS
Seat
Assembly
1PCS
Rear
Cover
Strip
Front/Rear
Brace
2PCS
A B
C D E F
G H I J K L

Required Tools
7/16
Socket Wrench
7/16
Wrench
#2 Square Bit

Assembly Instructions
Step 1
Unscrew the loosely attached
1.25 in(F) & 1.625 in(G)
screws, and remove the rear
cover strip (K) and place
aside for final assembly.
Step 2
Begin the assembly process
by placing the chair in the
orientation shown to the right,
with the back (I) and seat
assembly (J) on their side.

Step 3
Align the holes on the arm
assembly (H) with the holes
going through the back (I)
and seat assemblies(J).
Step 4
Insert the 3.5 inch bolt (C)
through a washer (D) and
into the leg/arm (H), back (I)
and seat (J) assemblies.

Step 5
Insert the 2.5 inch bolt (A)
through a washer (D) and
into the leg/arm (H) and seat
(J) assemblies.
Step 6
On the back side of the bolts
(A & C) that were inserted
through the seat (J), place a
washer and then thread a nut
onto all of the bolts placed in
steps 3-4. Tighten with 7/16
socket and wrench.
Step 7
Place the 3 inch bolt (B)
through the leg/arm assembly
(H) and the back assembly(I).

Step 8
On the back side of the bolt
placed in step 6 (B), place a
washer (D) and then thread a
nut (E) onto the bolt. Tighten
with a 7/16 socket and
wrench.
Step 9
Repeat steps 1-7 for other
leg/arm assembly (H) of
chair.
Step 10
When both leg/arm
assemblies (H) have been
attached to the chair, place
the chair in the orientation
showed to the right.
Step 11
Align the holes that are
predrilled in the leg/arm
assemblies (H) with the holes
on the front brace (L), then
use the provided 1.625 inch
screws (G) to attach the front
brace (L). The screws are a
#2 Square bit. The brace with
the buck logo will be mounted
here with the logo facing out.

Step 12
Align the holes that are
predrilled in the rear of the
leg/arm assembly (H) with
the holes in the rear brace
(L). Using the provided 1.625
inch screws (G) attach the
rear brace (L)to the leg/arm
assemblies (H). The screws
are a #2 Square bit.
Step 13
Align the rear cover strip (K)
with the predrilled holes on
the back and seat assemblies
(I & J).
Step 14
Reattach the rear cover strip
removed in Step 1, (K) to the
back and seat assemblies (I
& J) using the provided 1.25
inch (F) and 1.625 inch
screws (G). The screws are a
#2 Square bit.