Buderus Logamatic TC100 User manual

6720889234 (2018/10) en
Installation and operating instructions
Remotely operated controller
Logamatic TC100

Table of contents
Logamatic TC100 – 6720889234 (2018/10)
2
Table of contents 1 Safety instructions
1.1 Explanation of symbols
Information symbol
Important information is placed between 2 lines and marked with an
i-symbol in a square.
Additional symbols
Table 1
Please read this instruction carefully before use.
1.2 Safety instructions
This temperature controller is used to control a heat source in your
dwelling.
• Do not disassemble the temperature controller under any
circumstances.
• Avoid high temperatures, moisture and dusty environments.
• In order to prevent a short circuit or damage to the controller: Do not
use any liquids or cleaning agents when cleaning.
• Switch off the mains voltage of the heat source before installing.
2 Environmental protection/disposal
Environmental protection is a fundamental corporate strategy of the
Bosch Group.
The quality of our products, their economy and environmental safety are
all of equal importance to us and all environmental protection legislation
and regulations are strictly observed.
We use the best possible technology and materials for protecting the
environment taking account of economic considerations.
Packaging
Where packaging is concerned, we participate in country-specific
recycling processes that ensure optimum recycling.
All of our packaging materials are environmentally compatibleand can be
recycled.
Used electrical and electronic appliances
Electrical or electronic devices that are no longer
serviceable must be collected separately and sent for
environmentally compatible recycling (in accordance with
the European Waste Electrical and Electronic Equipment
Directive).
To dispose of old electrical or electronic devices, you should use the
return and collection systems put in place in the country concerned.
Batteries must not be disposed together with your household waste.
Used batteries must be disposed of in local collection systems.
1 Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.1 Explanation of symbols . . . . . . . . . . . . . . . . . . . . . . . . . . 2
1.2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
2 Environmental protection/disposal . . . . . . . . . . . . . . . . . . . . . 2
3 Product information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.1 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.2 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.3 Warranty conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.4 Declaration of Conformity (Europe) . . . . . . . . . . . . . . . . 3
3.5 Data privacy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.6 Data connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.7 Proximity sensor and touch screen. . . . . . . . . . . . . . . . . 3
3.8 Ambient Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4 Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.1 Prior to installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.2 Determining the installation location . . . . . . . . . . . . . . . 3
4.3 Fitting the wall plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.4 Connecting to the heat source. . . . . . . . . . . . . . . . . . . . . 4
4.5 Installing (deinstalling) the controller. . . . . . . . . . . . . . . 5
5 Commissioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5.1 Powering up Logamatic TC100 . . . . . . . . . . . . . . . . . . . . 5
5.2 Software update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
5.3 Operation of the touch screen. . . . . . . . . . . . . . . . . . . . . 5
5.4 Connecting with WLAN network . . . . . . . . . . . . . . . . . . . 5
5.5 Entering the WLAN network password . . . . . . . . . . . . . . 6
5.6 MyMode app. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
5.7 Electronic thermostatically controlled radiator
valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6 Operating the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6.1 Start screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
6.2 Symbol background . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6.3 Tab pages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6.4 Temperature setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6.5 Manual operation or time program . . . . . . . . . . . . . . . . . 7
6.6 Away setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
6.7 DHW heating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.8 Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.8.1 WLAN setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.8.2 Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
6.8.3 Firmware versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7 Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
8 Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
9 ErP Class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
10 List of used Open Source Components . . . . . . . . . . . . . . . . . . . 9
11 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
11.1 Apache License 2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
11.2 BSD (Three Clause License) . . . . . . . . . . . . . . . . . . . . . 11
11.3 MIT License. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
11.4 Texas Instruments-Software License Agreement. . . . . 11
12 Technical terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Symbol Meaning
▶ a step in an action sequence
a reference to a related part in the document
• a list entry
–a list entry (second level)

3Product information
Logamatic TC100 – 6720889234 (2018/10) 3
3 Product information
3.1 Scope of delivery
Fig. 1 Scope of delivery
[1] Logamatic TC100
[2] Quick Install Guide
[3] Screw with rawl plug 2 ×
[4] Wall plate
3.2 Accessories
The following accessories are available:
• Smart Radiator Thermostats
• Logamatic TC100 adaptor
• Logamatic TC100 app (free of charge).
Visit www.buderus-logamaticTC100.com for an up-to-date overview.
3.3 Warranty conditions
A manufacturer's warranty of 2 years is provided for Logamatic TC100.
3.4 Declaration of Conformity (Europe)
Hereby, Bosch Thermotechnik GmbH, declares that the radio
equipment with type TC100.2 are in compliance with Directive
2014/53/EU.
The complete text of the EU Declaration of Conformity is available on the
Internet: www.buderus-logamaticTC100.com/manual.
3.5 Data privacy
Information about data protection can be found on the Logamatic TC100
site under Data protection.1)
3.6 Data connection
▶ Logamatic TC100 supports open WLAN connections and WLAN
connections encrypted with WEP 128, WPA and WPA2 protocols.
WPA2 is the safest protocol and is therefore preferred.
▶ “Hidden” networks are not supported.
▶ Logamatic TC100 takes over the time setting of the Buderus server.
If there is no connection to the server, Logamatic TC100 can only be
put into operation in manual operation.
▶ All costs for creating an Internetconnection and asmart device are to
be borne by the user.
▶ The type of connected heat source determines, which functions can
be used. Consult the Logamatic TC100 site to gain an overview of
which functions are available for which heat source.1)
3.7 Proximity sensor and touch screen
Fig. 2 Proximity sensor and touch screen
[1] Proximity sensor
[2] Touch screen
A proximity sensor [1] detects a presence in front of the touch screen
[2] and lights up. If nothing more is detected for a short period of time,
the touch screen automatically switches off. If the detection lasts for
longer than 5 minutes, the touch screen automatically switches off.
▶ If required, clean the touch screen with a clean, dry cloth.
3.8 Ambient Light
Logamatic TC100 not only communicates with you via the app, but also
via Ambient Light. As soon as you send a heating command via the app to
Logamatic TC100, it lights orange for a second when you increase the
temperature, and blue when you lower the temperature. When you leave
your home, a green light for a second indicates that the heating system
has automatically switched to away mode. Red light: Error occurred in
your heating system. If everything is running normally, Ambient Light will
be off.
4 Assembly
4.1 Prior to installation
▶ Prior to installation, check that Logamatic TC100 can be combined
with the heat source.
On the Logamatic TC100 site there is a list of possible combinations with
or without the operation of Logamatic TC100.1)
Minimum requirements for installation:
▶ 2-wire cable to a heat source,which is suitable for use with Logamatic
TC100.
▶ Broadband internet access via WLAN 802.11 b/g (2.4 GHz) for use
with the app and internet functions.
4.2 Determining the installation location
A reference room is a room (for example the living room), where the
temperature, which is representative ofthe whole dwelling, is measured,
and where most time is spent.
1) See the back of this document for the web address.
0010018147-001
2x
Quick install guide
1
2
3
4
0010018148-001
1
2

4Assembly
Logamatic TC100 – 6720889234 (2018/10)
4
If weather-compensated control is used, it is not necessary to locate the
controller in the reference room.
▶ Install the controller on an internal wall in the reference room.
Ensure that there is sufficient clearance around the controller.
Fig. 3 Installation location for controller, clearance
Fig. 4 Installation location for controller, condition
4.3 Fitting the wall plate
When replacing a controller with Logamatic TC100, the existing wall
plate can continue to be used (section 4.5).
This wall plate can be fastened directly to the wall, for example at the
location of the previous controller.
▶ Pull the mains plug of the heat source from the socket.
When fitting to a recessed wall box, ensure that the room temperature
measurement can not be impaired by any draughts. If required, stuff the
recessed wall box with thermal insulation material.
▶ Connect the lead (EMS-BUS connection of the heat source) to the
terminals on the wall plate. The wires can be connected in any order.
Fig. 5 Connecting the wall plate
4.4 Connecting to the heat source
The installation instructions for the heat source contain further
information about the connection of Logamatic TC100.
Fig. 6 Connecting the Logamatic TC100 adaptor
[1] Logamatic TC100 adaptor
[2] Heat sources which use iRT, OpenTherm or On-Off
There are various possibilities for connection to a heat source:
• Replacing an existing controller on the same wall plate. Logamatic
TC100 is ready for operation.
• Buderus1) heat source appliance with a visible orange controller
connection on the underside. Connect Logamatic TC100 with the
orange connector at the orange terminal.
• Buderus1) heat source appliance without a visible connection for the
controller. The heat source must be opened by a recognized installer.
• Heat sources, which use iRT, OpenTherm or On-Off, can only be
connected with an Logamatic TC100 adaptor (accessory).
For more up-to-date information see the back of this document for
the web address or consult a recognized installer.
0010018149-001
1,2 - 1,9 m
≥ 0,75 m
≥ 1 m
≥ 0,6 m
0010018150-001
≥ 1 m
≥ 0,4 m
≥ 0,6 m
1) Or a Bosch Group brand (Nefit, Junkers, Worcester, ELM LeBlanc).
0010018151-002
EMS
l100 m EMS BUS
0010018152-002
l ≤ 100 m
l≤ 3 m
12

5Commissioning
Logamatic TC100 – 6720889234 (2018/10) 5
4.5 Installing (deinstalling) the controller
Fig. 7 Installing (deinstalling) the controller
Installing
▶ Hook Logamatic TC100 behind the wall plate[1].
▶ Press Logamatic TC100 with the underside against the wall plate,
until an audible “click” is heard [2].
Logamatic TC100 is now locked.
Deinstalling
▶ Unlock Logamatic TC100 by pressing the unlocking key [3].
▶ Slightly lift the underside of Logamatic TC100 and remove it [4].
5 Commissioning
5.1 Powering up Logamatic TC100
▶ Remove the protective film from Logamatic TC100.
▶ Plug the mains plug of the heat source into the socket.
▶ Switch on the heat source.
This also causes Logamatic TC100 to be supplied with mains voltage,
and it searches for a connection to:
• the heat source [1],
• a WLAN network [2],
• the Buderus server [3].
Fig. 8 Start screen
[1] Connection with the heat source
[2] Connection with WLAN network
[3] Connection with Buderus server
[4] Software version (example)
[5] Connection made (example)
[6] Connection not made (example)
A green check mark [5] shows, that the connection is made. A red cross
[6] shows, that the connection is not made. See section 7, page 8 for an
overview of possible causes and solutions.
5.2 Software update
The software version of this document is 01.xx.xx. The installed
software version is shown in the start screen [4]. Software updates are
performed automatically. It is possible that, when delivered, Logamatic
TC100 does not yet have the current software version and does not
therefore support all the functions in the app. The automatic update may
take some time to start. Via the app an update can start immediately.
After an update has been performed, the arrangement of the touch
screen may differ from this document. See the latest version of this
document on the Logamatic TC100 site for Buderus.1)
5.3 Operation of the touch screen
It is possible to change the settings by means of a horizontal or vertical
wiping movement (swipe) or by pressing (tap). Only operate the touch
screen with your hand.
Fig. 9 Swipe or tap
5.4 Connecting with WLAN network
Logamatic TC100 can only make a connection to “visible” networks. If
Logamatic TC100 is to establish a connection with a “hidden network”,
this must first be made “visible”. After a connection has been
established, the network can be “hidden” again.
After Logamatic TC100 has been connected to the heat source, it
automatically searches for WLAN networks [3] and displays these on the
touch screen. While the search is being performed, a flashing WLAN
symbol appears on the touch screen.
Fig. 10 Available WLAN networks
[1] Cancel key
[2] Return key
[3] Available WLAN networks
0010018153-001
1. 1.
2. 3. 4.
0010018154-002
01.nn.nn
1
2
3
4
5
6
1) See the back of this document for the web address.
0010018156-001
0010018157-003
Home 3
Home network ...
WLAN 8
WLAN 7
1
3
2

6Operating the appliance
Logamatic TC100 – 6720889234 (2018/10)
6
▶ Swipe vertically to find the WLAN network.
▶ Select the desired WLAN network by tapping.
If the WLAN network is secured with a password:
▶ Enter the WLAN network password (section 5.5).
If the desired WLAN network is not found:
▶ Press the Cancel key [1] to set the controller to the Offline mode.
The temperature can now only be set in manual operation on the
touch screen. Connection to the app or Buderus site is not possible.
Possible connection difficulties, section 6.8, page 8 and
chapter 7, page 8.
When all the connections have been established, the data is
synchronised. The start screen appears on the touch screen.
5.5 Entering the WLAN network password
Logamatic TC100 uses the standard WLAN protocol.
▶ Do not therefore use any $ characters in the WLAN network
password.
Fig. 11 Entering the WLAN network password
Using the Return key [8], one can return to the previous display. An input
error can be corrected with the “Back” key [3]. An input is confirmed
with the Enter key [1]. The password can be entered into the input line
[2] using the keys [4]. Use the shift key [5] to enter capital letters.Using
key [6], special characters can be entered. The lock key [7] shows, that
the WLAN network is secured.
▶ Enter the WLAN network password.
▶ Confirm the password with the Enter key [1].
Now the start screen appears (section 6.1).
5.6 MyMode app
The MyMode app contains functions, which are not included in
Logamatic TC100.
▶ Download the MyMode app from Buderus.
▶ Install the MyMode app from Buderus.
▶ Register the app with Logamatic TC100.
▶ Enter the one-off access code or scan the QR code (sticker on the
Quick Install Guide).
▶Establishaconnectionwith Logamatic TC100.
▶ Enter the personalised password.
On www.buderus-logamaticTC100.com you can find an overview of the
compatible smart devices.
5.7 Electronic thermostatically controlled radiator valve
Logamatic TC100 can establish a wireless connection with up to 19
Bosch electronic thermostatically controlled radiator valves
(accessories).
In this way different temperatures can be set in different rooms.
▶ Connect the electronic controller valves via the MyMode app (pair).
See the manual of the electronic thermostatically controlled radiator
valves or use the steps in the MyMode app.
6 Operating the appliance
6.1 Start screen
Fig. 12 Start screen
[1] Current room temperature
[2] Space for notification symbols
[3] Display for heat source modulation level
[4] Set temperature
[5] Space for operational and warning symbols
[6] Tab pages
[7] Display for economical heating
[8] Eco symbol
If the touch screen is not used for some time, the device returns
automatically to the start screen and the touch screen switches itself off.
The current room temperature is in the middle [1], and the set
temperature is beside it [4]. The modulation level of the heat source is
depicted with a display [3]. The Eco symbol [8] with the display for
economical heating [7] shows, how energy-efficient the heating of the
room is.
Notification symbols
The space for notification symbols [2] may contain the following
symbols:
0010018158-002
1
2
3
4
7
8
6
5
play
ANDROID APP ON •Away
•NoEMS
0010018159-001
3
1
5
4
8
7
6
2

6Operating the appliance
Logamatic TC100 – 6720889234 (2018/10) 7
Operational symbols
The space for operational symbols [5] may contain the following
symbols:
Warning symbols
The space for warning symbols [5] may contain the following symbols:
Symbols on tabs
The following symbols may appear on the tabs:
6.2 Symbol background
Fig. 13 Symbol background
Symbols can have differently coloured backgrounds. A light blue
background shows, that this function is active. [1]. A dimmed blue
background shows, that this is not active [2]. A grey background shows,
that this function is not available [3]. If a function is tapped, which is not
available, a red cross appears over this background [4].
6.3 Tab pages
Logamatic TC100 contains several tab pages (fig. 12, [6]).
The number of available tab pages depends on the system. The start
screen is on the 1st tab page.
▶ Swipe right or left to change between the tab pages.
6.4 Temperature setting
Fig. 14 Temperature setting
▶ Tap on the start screen to get to the temperature setting screen.
▶ Swipe vertically to increase or reduce the set temperature.
6.5 Manual operation or time program
Fig. 15 Selecting manual operation or time program
The time program can be set with the MyMode app. The time program
can be switched on or off with Logamatic TC100.
▶ Swipe horizontally to the correct tab page.
▶ Tap on the Manual operation [1] key or Time program [2] key to
change between these functions.
6.6 Away setting
Fig. 16 Selecting “Not at home” or “At home”
The “Away” setting is used to show, whether one is at home or not. The
set temperature is lowered in “Away from home status” by15 °C (60 °F).
This standard value can be changed in the MyMode app. This function is
only available in time program mode.
▶ Swipe horizontally to the correct tab page.
▶ Tap on the key for “Away” [1] or “Home” [2] to change between these
functions.
• No WLAN connection
• No connection with the Buderus server
• DHW is maintained at temperature
• DHW is not maintained at temperature
• Heat source in operation for CH
• Heat source in operation for CH optimum start
•Fireplace
•Event
• Maintenance request from the heat source
• Fault signal from the heat source
• Manual operation
• Time program
• Home/Away setting
• DHW mode permanently On/Off
• DHW mode On/Off automatically
• WLAN settings
0010018160-001
1 2 3 4
0010018161-001
20°C
5
2
1
°
C
0
2
0
°C
0
0010018162-001
21
0010018163-001
21

7Faults
Logamatic TC100 – 6720889234 (2018/10)
8
6.7 DHW heating
Fig. 17 Switching DHW heating on or off and DHW time program
If “DHW according to program” is switched on in the MyMode app, the
setting for DHW heating can be adjusted on Logamatic TC100.
Fig. 18 DHW not available
6.8 Settings
Fig. 19 WLAN setting
[1] WLAN settings
[2] Reset (factory settings)
[3] Information about the current software version
6.8.1 WLAN setting
▶ Press the WLAN symbol [1] to adjust the WLAN network or
password.
6.8.2 Reset
If Logamatic TC100 is reset to factory settings, all personal settings will
be lost.
To prevent data loss, in the event of a malfunction, first consult the
solutions (chapter 7) or perform a soft reset.
Soft reset
If Logamatic TC100 no longer functions correctly, perform a soft reset
while maintaining all settings.
▶ Disconnect Logamatic TC100 from the wall plate for a moment
(fig. 7, page 5).
Hard reset (factory settings)
A hard reset resets Logamatic TC100 to the factory settings.
After confirmation, the WLAN data is deleted and must be reset
(section 5.4).
1. Hard reset via touch screen
▶ Press the trash bin symbol [2] to reset the factory settings, there are
2 options:
– fully back to the factory settings
(Caution! Consumption data will be lost).
– return to the factory settings while
maintaining the consumption data.
2. Hard reset with a paperclip
Fig. 20 Hard reset
▶ Press the reset button (fig. 20) for a few seconds.
Caution! All personal settings (including consumption data) will be
deleted and the WLAN connection will have to be reset
(section 5.4).
The problem has not yet been solved:
▶ Consult the installer.
6.8.3 Firmware versions
▶ Press the info symbol [3] to request the information of the current
software.
7Faults
The fault displays for the heat source are visible on the touch screen and
are sent automatically from the controller to the MyMode app. Contact
with the installer can be selected in the app.
There is an extensive list on the Logamatic TC100 site with solutions for
any problems with Logamatic TC100 that may arise.1)
0010018164-001
1 2
0010018165-001
3
0010018743-001
1
2
3
1) See the back of this document for the web address.
Fault Remedy
No WLAN connection. The WLAN signal for the WLANi
router may be too weak. Install a WLAN amplifier.
WLAN
network not
found
The “Hide” function for the WLAN router is possibly
switched on, or the “Broadcast” function (sending
SSID) may be switched off. Temporarily switch off the
“Hide” function or switch on the “Broadcast” function.
0010018166-002

8Technical data
Logamatic TC100 – 6720889234 (2018/10) 9
Table 2 Fault overview (the symbols are displayed on the touch screen)
8Technicaldata
Table 3
9ErPClass
The data in the table below is needed to fill out the Energy related
Product (ErP) form and the ErP Data Label sticker, which are required for
systems.
Supplier is “Buderus, Bosch Group”, the model is “Logamatic TC100”.
Table 4
10 List of used Open Source Components
The following text is in English for legal reasons.
The following open source software (OSS) components are included in
this product:
No connection to the Internet server. Wait until the
connection to the Internet server has been
automatically restored. Even without a server
connection, the heat source can be controlled in
manual operation or via the time program after it has
been put into operation.
Forgotten
serial number
and access
code
The serial number and access code are both on the
sticker, which is on the front of the brief installation
instructions, and on the sticker at the back of
Logamatic TC100 and is incorporated in the QR code
with which it can be entered. If the app is used to log
on, the serial number and access code can be
displayed in the app, by navigating via the “Info menu”
to the “Product information” submenu. If the serial
number and accesscode can not be found, please
contact “Consumer Info”.1)
Theapphas no
contact with
Logamatic
TC100
Does Logamatic TC100 have a connection to the
Internet (section 5.4)? Serial number and access
code entered? Please note, these are capital letter
sensitive. There is possibly a slow Internet connection.
Wait for a few minutes.
The displayed
temperature
is too high or
too low
The displayed temperature can be set in the app or on
the Logamatic TC100 site1)
The touch
screen does
not function
If the touch screen does not detect anything for more
than 5 minutes, it automatically switches itself off.
After this, the touch screen can only be activated again
by touching it.
Passwordwith
$ character
Logamatic TC100 uses the standard WLAN protocol.
Do not therefore use any $ characters in the WLAN
network password. Remove the $ character from the
network password.
Appisnotfully
functioning
It is possible that, when delivered, Logamatic TC100
does not yet have the current software version. This
means that possibly not all app functions can be used.
The software update occurs automatically and make
take some time or can be done manually via the
MyMode app: Info – About – Check & Update.
Indication of one of the following messages: repeated
ignition attempts, dripping/leaking DHW tap, too little
flow through the heating system, leak in the heating
system, boiler pressure too low, or heat source shows
the Maintenance symbol. These are informative
signals. The heat source is functioning normally.
The heat source is malfunctioning. Check the MyMode
app for more information.
No software
updates have
been received
from
Logamatic
TC100
Software updates are performed automatically.
This requires a continuous Internet connection.
If the router is provided with a timer, updates can be
missed.
Fault Remedy
TC100.2
Description Unit Value
UVDC 14.3 – 16.0
Pmax W0.9
mg (lb) 250 (0.551)
f1 (RF) f = 868.3 …
869.5 MHz [EU]
(P = max. 13.4 dBm)
Tamb °C ( °F) 0 … 45 (32 … 113)
IP-class IP30
φ% RH 10 … 90
WLAN f = 2400 MHz …
2483.5 MHz
IEEE 802.11b (P = max. 17 dBm)
IEEE 802.11g (P = max. 14.1 dBm)
f2 (RF) f = 2400 MHz …
2483.5 MHz
IEEE 802.15.4 (P = max. 14.6 dBm)
mm (inch) h = 153 (6)
w =103 (4)
d = 24 (1)
Operating functions and ErP description ErP
class
Additional
room heating
energy
efficiency
Room temperature-dependent, modulating V 3%
Weather-compensated with influence of
room temperature, modulating
VI 4%
Room temperature control system with
several temperature sensors (zone
control), modulating
VIII 5%
Name of OSS
Component
Version of OSS
Component
Name and
Version of
License
(License text
can be found in
chapter 11)
Copyright
base64 2.1.0 MIT License See Appendix § 11.3.
Written by Peteris Krumins
http-parser 2.6.0 MIT License See Appendix § 11.3.
Copyright © Joyent, Inc.
and other Node contributors
MD5 2.2.1 Apache License
2.0
See Appendix § 11.1.
Copyright © 2006-2015
ARM Limited

11 Appendix
Logamatic TC100 – 6720889234 (2018/10)
10
Table 5
11 Appendix
11.1 Apache License 2.0
Apache License Version 2.0, January 2004
http://www.apache.org/licenses/
TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND
DISTRIBUTION
1. Definitions.
“License” shall mean the terms andconditions for use,reproduction, and
distribution as defined by Sections 1 through 9 of this document.
“Licensor” shall mean the copyright owner or entity authorized by the
copyright owner that is granting the License.
“Legal Entity” shall mean the union of the acting entity and all other
entities that control, are controlled by, or are under common control with
that entity. For the purposes of this definition, “control” means (i) the
power, direct or indirect, to cause the direction or management of such
entity, whether by contract or otherwise, or (ii) ownership of fifty
percent (50%) or more of the outstanding shares, or (iii) beneficial
ownership of such entity.
“You” (or “Your”) shall mean an individual or Legal Entity exercising
permissions granted by this License.
“Source” form shall mean the preferred form for making modifications,
including but not limited to software source code, documentation
source, and configuration files.
“Object” form shall mean any form resulting from mechanical
transformation or translation of a Source form, including but not limited
to compiled object code, generated documentation, and conversions to
other media types.
“Work” shall mean the work of authorship, whether in Source or Object
form, made available under the License, as indicated by a copyright
notice that is included in or attached to the work (an example is provided
in the Appendix below).
“Derivative Works” shall mean any work, whether in Source or Object
form, that is based on (or derived from) the Work and for which the
editorial revisions, annotations, elaborations, or other modifications
represent, as a whole, an original work of authorship. For the purposes
of this License, Derivative Works shall not include works that remain
separable from, or merely link (or bind by name) to the interfaces of, the
Work and Derivative Works thereof.
“Contribution” shall mean any work of authorship, including the original
version of the Work and any modifications or additions to that Work or
Derivative Works thereof, that is intentionally submitted to Licensor for
inclusion in the Work by the copyright owner or by an individual or Legal
Entity authorized to submit on behalf of the copyright owner. For the
purposes of this definition, “submitted” means any form of electronic,
verbal, or written communication sent to the Licensor or its
representatives, including but not limited to communication on
electronic mailing lists, source code control systems, and issue tracking
systems that are managed by, or on behalf of, the Licensor for the
purpose of discussing and improving the Work, but excluding
communication that is conspicuously marked or otherwise designatedin
writing by the copyright owner as “Not a Contribution”.
“Contributor” shall mean Licensor and any individual or Legal Entity on
behalf of whom a Contribution has been received by Licensor and
subsequently incorporated within the Work.
2. Grant of Copyright License.
Subject to the terms and conditions of this License, each Contributor
hereby grants to You a perpetual, worldwide, non-exclusive, no-charge,
royalty-free, irrevocable copyright license to reproduce, prepare
Derivative Works of, publicly display, publicly perform, sublicense, and
distribute the Work and such Derivative Works in Source or Object form.
3. Grant of Patent License.
Subject to the terms and conditions of this License, each Contributor
hereby grants to You a perpetual, worldwide, non-exclusive, no-charge,
royalty-free, irrevocable (except as stated in this section) patent license
to make, have made, use, offer to sell, sell, import, and otherwise
transfer the Work, where such license applies only to those patent claims
licensable by such Contributor that are necessarily infringed by their
Contribution(s) alone or by combination of their Contribution(s) with
the Work to which such Contribution(s) was submitted. If You institute
patent litigation against any entity (including a cross-claim or
counterclaim in a lawsuit) alleging that the Work or a Contribution
incorporated within the Work constitutes direct or contributory patent
infringement, then any patent licensesgranted to You under this License
for that Work shall terminate as of the date such litigation is filed.
4. Redistribution.
You may reproduce and distribute copies of the Work or Derivative
Works thereof in any medium, with or without modifications, and in
Source or Object form, provided that You meet the following conditions:
1. You must give any other recipients of the Work or Derivative Works a
copy of this License; and
2. You must cause any modified files to carry prominent notices stating
that You changed the files; and
3. You must retain, in the Source form of any Derivative Works that You
distribute, all copyright, patent, trademark, and attribution notices
from the Source form of the Work, excluding those notices that do not
pertain to any part of the Derivative Works; and
4. If the Work includes a „NOTICE“ text file as part of its distribution,
then any Derivative Works that You distribute must include a readable
copy of the attribution notices contained within such NOTICE file,
excluding those notices that do not pertain to any part of the
Derivative Works, in at least one of the following places: within a
NOTICE text file distributed as part of the Derivative Works; within
the Source form or documentation, if provided along with the
Derivative Works; or, within a display generated by the Derivative
Works, if and wherever such third-party notices normally appear. The
contents of the NOTICE file are for informational purposes only and
do not modify the License. You may add Your own attribution notices
within Derivative Works that You distribute, alongside or as an
addendum to the NOTICE text from the Work, provided that such
additional attribution notices cannot be construed as modifying the
License.
You may add Your own copyright statement to Your modifications and
microJSON 1.3 BSD (three
Clause License)
See Appendix § 11.2.
Copyright © 2014 Eric S.
Raymond
Texas
Instruments
2.1.0 Texas
Instruments-
Software
License
Agreement
See Appendix § 11.4.
Copyright © 2016 Texas
Instruments Incorporated
Yxml 10/27/2015 MIT License See Appendix § 11.3.
Copyright © 2013-2014
Yoran Heling
Name of OSS
Component
Version of OSS
Component
Name and
Version of
License
(License text
can be found in
chapter 11)
Copyright