Bueno Electric HFB-FO-LON Series User manual

Https://www.bueno-electric.com BUENO ELECTRIC
BUENO ELECTRICBUENO ELECTRIC
BUENO ELECTRIC
Contact: [e-mail] Fax: [phone]
HFB-FO-LON Series
Lonworks Fiber Optic Modem
Datasheet & User Manual

Page 2 of 7
Table of Contents
1. Overview ...........................................................................3
1.1 Introduction : ……………………….……………………………..3
1.2 Technical Specification……………………………...………….3
1.3 Warranty .…………………...……………………….…..……...4
2. Installation ........................................................................5
2.1 Package ontents ………………………………………..…....5
2.2 Enclosure ...................................................... .......... .......... 5
2.3 Install Method....................................................................…6
2.4 Install Application ..............................................................…7
3. Dimensions .......................................................................8

Page 3 of 7
1. Overview
1.1 Introduction
The LONWORKS Fiber Optic Modem is a multi-master and high performance Field bus Control
S stem (FCS). Our Fiber Optic Modem uses the fiber cable as its transmission medium and
utilizes Optical Fiber modulation/demodulation technolog to changes the electric medium into
a light medium transmission.
The LONWORKS Fiber Optic Modem product eliminates man of the disadvantages of copper
cable. Examples of these disadvantages are EMI/RFI, ground loops (electrical isolation with
fiber), high attenuation (high signal loss), short transmission distance between nodes of a
s stem, and potential lightning damage.
The LONWORKS Fiber Optic Modem can be widel used, such as Industrial Controls, Intelligent
Transportation S stems (ITS), Industrial Networking, Supervisor Control and Data (SCADA)
and so on
1.2 Technical S ecification
CAN BUS
onnectors Terminal
Standard LONWORKS(LonTalk)
Data Rate 78.6Kbps
Extended Distance 0~20Km
OPTICAL
Number of Fibers 2
Wavelength 850/1310nm(MM),1310/1550nm(SM)
Fiber Type 62.5/125μm(MM), 9/125μm(SM)
Distance 0 ~ 2Km OR 0-20 Km
onnector Type ST/P or S /F
GENERAL
Operating Temperature -30~ 70˚ / -30 ~ +158ºF
Operating Humidity 0 ~ 95% non-condensing
Mean Time Between Failure (MTB) > 70,000hrs
Power Supply Adaptor D 24V
Dimensions (H ×L×W)
125(L) × 110(W) × 36(H)

Page 4 of 7
1.3 Warranty
 Repair
 Please contact your local distributors when product is defective. Please apply RA in
advance and prepay shipping cost when returning the defective product to us. We will
pay the cost for sending it back to you.
 Please attach a statement clearly describing the problem.
 We will repair defective product under warranty free of charge to our customer.
 5 years warranty for product only.
 Any unauthorized modification of hardware and software voids the warranty.
 Warranty does not cover mishandling and/or abuse of the product.

Page 5 of 7
2 Installation
2.1 Package Contents
• OneLonworksFiber Optic Modem
• One power supply adaptor
• One User Manual
Please contact dealer or distributor if part is missing or damaged.
2.2 Enclosure
Fiber O tic Modem To View
LED Indicators:
POW: Power Supply, On if power input is OK.
TX: Fiber Link, Flashing if data transmitting is in OK.
RX: Fiber Link, Flashing if data receiving is in OK.
Fiber O tic Connectors:
TX: Transmitter (Fiber Optic ST)
RX: Receiver (Fiber Optic ST)
Terminal Definition

Page 6 of 7
Terminal pins assignment:
V+ Connect 24V power supply”+“
N/A N/A
V- Connect 24V power supply”-“
N/A N/A
N/A N/A
N/A N/A
N/A N/A
GND GND of LON
T+ LONA
—— R- LONB
2.3 Install Methods
1. Switch off all power supply before installation.
2. onnect the local “TX” Fiber Optic to the remote “RX” Fiber Optic, the local “RX” to the
remote “TX”. And ensure that fiber is properly aligned to the receiving connector.
2.4 Install A lication
1
2
3
4
5
6
7
8
9
0

Page 7 of 7
3 Dimensions (mm)
Wall Mount:
36
121.1
149
5
8
135.1
106.1
34