Buffalo AmeriHome MCDSG User manual

MCDSG
Double Seat Glider Chair
WARNING!
Maximum Weight Capacity Is 400 lbs
READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT.
This manual provides important information on proper operation & maintenance. Every effort has been
made to ensure the accuracy of this manual. These instructions are not meant to cover every possible
condition and situation that may occur. We reserve the right to change this product at any time without
prior notice.
IF THERE IS ANY QUESTION ABOUT A CONDITION BEING SAFE OR
UNSAFE, DO NOT OPERATE THIS PRODUCT!
QUESTIONS OR PROBLEMS? CONTACT CUSTOMER SERVICE FIRST.
If you experience a problem, have questions or need parts for this product, call Customer Service at
1-636-532-9888, Monday-Friday, 8 AM - 4 PM Central Time. A copy of the sales receipt is required.
FOR CONSUMER USE ONLY – NOT FOR PROFESSIONAL USE.
KEEP THIS MANUAL, SALES RECEIPT & APPLICABLE WARRANTY FOR FUTURE
REFERENCE.

MCDSG Double Seat Glider Chair Assembly Instructions 2
5) Long Frame Crossbar - 1 piece
13) Large End Cap - 2 pieces
Unpack product from package and review contents. Keep all packaging until product has been
reviewed. This product should be inspected prior to use to make certain all parts are intact and safe to
use after assembly.
Never allow children to use this product without responsible adult supervision.
Some chemicals can damage the finish on the product. Do not use harsh chemicals such as alcohol,
ammonia, gasoline, carbon tetrachloride, paint thinner, etc. to clean this product. Use soap and water.
Locate all parts before assembly. Two adults may be required for assembly. During assembly, position on
soft carpet or non-abrasive surface to avoid damage to the chair. Do not tighten screws until assembly is
complete.
After assembly: Regularly check all bolts and tighten any that are loose.
Tools Required: 4mm Hex Wrench, Phillips Screw Driver, 10mm Combination Wrench
COMPONENTS
A) Acorn Nut - 29 Pieces
B) Short Screw - 10 pieces
C) Plastic Spacer - 4 pieces
D) Long Screw - 19 pieces
E) Large Washer - 16 pieces
F) Lock Nuts - 29 pieces
G) Small Washer - 62 pieces
H) Small End Cap - 2 pieces
1) Main Frame - 2 pieces
3) Side Support - 2 pieces
8) Chair Back -
2 pieces
6) Swing Arms - 4 pieces
9) Chair Seat -
2 pieces
2) Short Frame Crossbar - 1 piece
7) Chair Frame Arm - 2 pieces
4) Chair Frame Crossbar - 1 piece
10) Small Support - 1 piece
11) Hex Wrench - 1 piece
12) Wrench - 1 piece

MCDSG Double Seat Glider Chair Assembly Instructions 3
(NOTE) Make sure the Swing Arm is placed at
top on INSIDE. But on bottom it is on
OUTSIDE. Also, make sure the shape of the
Swing Arm is pointed toward the INSIDE, but
at bottom it is pointed toward the outside. Use
Long Screws. At top make sure a Plastic
Spacer is used between Main Frame and
Swing Arm. (Later, when assembly is
complete, an Acorn Nut #A will be added on
top of the Lock Nut.)
3) Place the Chair Frame inside the Main Frame.
4) Locate the Swing Arm pieces. Connect Main
Frame #1 & Chair Frame Arm #7. Use Long Screw +
Small Washer + Frame + Small Washer + Lock Nut.
5) Attach Long Frame Crossbar #5 using
Long Screw + Small Washer + Lock Nut.
ASSEMBLY
1) Connect Main Frame #1 & Short Frame
Crossbar #2. Insert the Large End Cap #13 for
Feet. Use Long Screw + Small Washer + Frame +
Small Washer + Lock Nut.
2) Connect Chair Frame Arm #7 and Chair Frame
Crossbar #4 by firmly pressing the kinked end into
the open end. Insert Small End Cap #H into Chair
Frame.

MCDSG Double Seat Glider Chair Assembly Instructions 4
6) Combine the Chair
Back and Chair Seat by
using 4 pieces Short
Screws + Small Washer
+ Lock Nut.
7) Combine the two Chairs by adding a Short Screw + Small Washer + Lock Nut
in the middle of the Chair Seat. Insert the Small Support #10 between the two
Chair Backs using Short Screw + Small Washer + Lock Nut.
10) Attach the Small Support #10 between the two Chair Backs
to the Chair Frame Crossbar using Short Screw + Small Washer
+ Lock Nut.
Before use, make sure all nuts are securely tightened.
(Factory may have included extra washers and nuts)
9) Add the Side Support #3 to the Chair
Backs and the Chair Frame Crossbar with
Long Screw + Small Washer + Lock Nut.
8) Attach the combined Chairs to the Chair Frame
Arm, at the side of the Chair Back and the Chair
Seat using Long Screw + Small Washer + Lock Nut.
201907

MCDSG Double Seat Glider Chair Assembly Instructions 5