Buffalo GC882 User manual

Please read and keep indoor use only. Don’t discard
the instruction
GC882 and GC883 Aluminium Heat Shades
OPERATING INSTRUCTIONS
INTRODUCTION
1. Read the instructions before using the appliance.
2. Clean Heat Shade thoroughly before and after each use following the cleaning
instructions provided in this manual.
ELECTRICAL REQUIREMENTS
This product should only be connected to the mains electricity supply by a qualified electrician. Hardwire the
Heat Shade into a suitable power supply with correct voltage and sufficient power capacity. Refer to the
product label (serial plate) on the warmer for voltage and wattage requirements.
SAFETY INSTRUCTIONS
1. All power must be disconnected at power source before any service procedure is performed.
2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep
combustible materials, such as drapes and other furnishings, away from appliance.
3. Extreme caution is necessary when any appliance is used by or near children and whenever the
appliance is left unattended.
4. Always disconnect appliance before cleaning, maintaining and adjusting it.
5. Do not operate any appliance with a damaged cord or plug if the appliance malfunctions or has been
dropped / damaged. Return appliance to an authorised service facility for examination, electrical or
mechanical adjustment, or repair.
6. Do not use outdoors. This appliance is not intended for wet or moist locations. Never locate appliance
where it may fall into water.
7. Avoid the use of extension cords. Do not run cord under carpeting, runners, or the like. Arrange cord away
from traffic area and where it will not create a trip hazard.
8. This appliance has electrical parts. Do not use it in areas where gasoline, paint, or flammable liquids are
used or stored.
9. This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety. Children should be
supervised to ensure that they do not play with the appliance.
10. If the supply cord is damaged, it must be replaced by the manufacturer, it’s service agent or similarly
qualified persons in order to avoid a hazard
WARNING!
This unit only suitable for R40 or BR40 type incandescent lamps.
The lamp is excluded from the warranty.
Buffalo Telephone Helpline:- 0845 146 2887 (United Kingdom)
PREPARATION
1. Remove the Heat Shade assembly from the carton.
2. Remove tape and protective packaging from all surfaces of unit.
3. Make sure the installation site provides the proper installation
clearances for the unit

INSTALLATION
1. Drill a 7/16” (11mm) hole through mounting fixture.
2. Pass wires from the shade through hole in fixture.
3. Secure the shade to the fixture with nut.
4. You may unscrew the threaded nuts to adjust the length to fit your requirements.
5. The wires in this product are brown – live, blue – neutral and green/yellow for earth.
Caution; Hot Surface.
CLEANING
NOTE: Proper maintenance plays an important part in the life span and functioning of the shade.
1. Disconnect the heat shade from the power source prior to cleaning and ensure the surface is cool.
2. This unit can be cleaned with a damp sponge and mild soap. Rinse with clean water and wipe dry.
3. Do not immerse in water or other liquid.
The heat lamp must not be cleaned by a water jet.
MAINTENANCE
HEAT BULB REPLACEMENT
NOTE: Each standard Heat Shade is suitable for a clear or infrared heat bulb rated at or below 250 watts.
1. To replace a bulb, place the switch in the OFF position and allow the bulb and shade to cool
completely.
2. Bulbs have a threaded base, Unscrew the bulb counterclockwise from the unit and replace with a new
bulb.
Disposal
EU regulations require product to be disposed of by specialist companies who remove or recycle all gasses,
metal and plastic components.
Consult your local waste collection authority regarding disposal of your appliance. Local authorities are not
obliged to dispose of commercial refrigeration equipment but may be able to offer advice on how to dispose of
the equipment locally. Alternatively call the BUFFALO helpline for details of national disposal companies
within the EU.
Compliance
The WEEE logo on this product or its documentation indicates that the product must
not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and
environmentally safe recycling process. For further information on how to dispose of
this product correctly, contact the product supplier, or the local authority responsible
for waste disposal in your area.
BUFFALO parts have undergone strict product testing in order to comply with regulatory standards and
specifications set by international, independent, and federal authorities.
BUFFALO products have been approved to carry the following symbol:

Conformiteitsverklaring • Déclaration de conformité • Konformitätserklärung • Dichiarazione di conformità •
• Declaración de conformidad • Declaração de conformidade
Equipment Type • Uitrustingstype • Type d'équipement • Gerätetyp •
Tipo di apparecchiatura • Tipo de equipo • Tipo de equipamento
Heat Shade
Model • Modèle • Modell • Modello • Modelo • Malli
GD882 GD883
Application of Council Directives(s)
Toepassing van Europese Richtlijn(en) • Application de la/des directive(s) du Conseil •
Anwendbare EU-Richtlinie(n) • Applicazione delle Direttive • Aplicación de la(s)
directiva(s) del consejo • Aplicação de directiva(s) do Conselho
LVD Directive 2006/95/EC
RoHS Directive 2011/65/EU
Standards
Standaarden • Normes • Normen • Standard • Estándares • Normas
EN 60598-2-4
SN/T2003.1-2005
Producer Name • Naam fabrikant • Nom du producteur • Name des Herstellers • Nome
del produttore • Nombre del fabricante • Nome do fabricante
Buffalo
Producer Address • Adres fabrikant • Adresse du producteur • Anschrift des
Herstellers • Indirizzo del produttore • Dirección del fabricante • Endereço do fabricante
Fourth Way, Avonmouth,
Bristol, BS11 8TB
United Kingdom
I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and Standard(s).
Ik, de ondergetekende, verklaar hierbij dat de hierboven gespecificeerde uitrusting goedgekeurd is volgens de bovenstaande Richtlijn(en)
en Standaard(en).
Je soussigné, confirme la conformité de l'équipement cité dans la présente à la / aux Directive(s) et Norme(s) ci-dessus
Ich, der/die Unterzeichnende, erkläre hiermit, dass das oben angegebene Gerät der/den oben angeführten Richtlinie(n) und Norm(en)
entspricht.
Il sottoscritto dichiara che l'apparecchiatura di sopra specificata è conforme alle Direttive e agli Standard sopra riportati.
El abajo firmante declara por la presente que el equipo arriba especificado está en conformidad con la(s) directiva(s) y estándar(es) arriba
mencionadas.
Eu, o abaixo-assinado, declaro que o equipamento anteriormente especificado está em conformidade com a(s) anterior(es) Directiva(s) e
Norma(s)
Date • Data • Date • Datum • Data • Fecha • Data
29/05/12
Signature • Handtekening • Signature • Unterschrift
Firma • Firma • Assinatura
Full Name • Volledige naam • Nom et prénom • Vollständiger Name •
Nome completo • Nombre completo • Nome por extenso
Richard Cromwell
Position • Functie • Fonction • Position • Qualifica • Posición • Função
Commercial Director

Buffalo Telephone Helpline:- 0845 146 2887 (United Kingdom)