Bull Outdoor Outlaw 26038 Quick reference guide

ASSEMBLY & OPERATING INSTRUCTIONS
MODEL #26038 OUTLAW 4 BURNER STAINLESS STEEL, BUILT-IN, L.P. (PROPANE)
MODEL #26039 OUTLAW 4 BURNER STAINLESS STEEL, BUILT-IN, N.G. (NATURAL GAS)

TABLE OF CONTENTS PAGE#
SAFETY INSTRUCTIONS
..............................................................................................................
, ...................................
2
THE LOCATION FGR YOUR GRILL.. .... ........ ............ ....... ........ ................................................. ............................... 2
CHECKING FOR
tSAS
LEAKS
....... ............ ............................. .. .................................. L ......................................
2
,Nsr?c; :;
;
E: s
I
•
<•••
:•:•••••• ••••
••••••••:•::•••·•·•·•·••·•·•·•·•·•·•·•·•·•·•
'i:•·· ·•·•·•·•·•·•·•••••·••••••••••·•·•
SPECIFICATIONS FOR BARBECUE STRUCTURE
....................................................................................... ................
5
CONNECTING TO GAS SOURCE..
..............................................................................................................................
6
NATURAL GAS CONNECTIONS
................................................................................................................................. .. 6
PROPANE GAS CONNECTIONS
...................................................................... ..............................................................
6
OUTDOOR NATURAL GAS BBQ INSTALLATION SPECIF/CATIONS
.................................................................................. 7
OUTDOOR PROPANE GAS BBQ INSTALLATION SPECIF/CATIONS
... ............................................................................. 8
LP GAS TANK RETENTION
......................................................................................................................................................................
9
INSPECTING/ CLEANING BURNERS AND GAS VALVE ORIFICES
..........................................................................................
10
BURNER CLEANING
..........................................................................................................................................
,
..................................... 10
BURNER SHUTTER CLIP INSPECTION
I
ADJUSTMENT... ...................... ........................................................................
10
BURNER REPLACEMENT INTO INSERT... ....................................................... .........................
..............
.......................
11
IGNITOR
I
ELECTRODE CHECK
................................................................................ ...........................
.....................
11
BURNER OPERATION CHECK
............................................................. ........................................................................
11
COOKING COMPONENT INSTALLATION
............................................................................................................................
13
LIGHTING & OPERA TING INSTRUCTIONS
.............................................................................................................................
14
LIGHTING PROCEDURES
................................................................................................................ .
...
..
........
.................
14
OPERA
TING PROCEDURE
....................................................................................................................................... ..
14
COOKING TEMPERATURES
........................................................................................................................................ 14
CLEANING & MAINTENANCE
...........................................................................................................................................
16
TROUBLESHOOTING
...............................................................................................................................................................................
17
IF GRILL FAILS TO OPERATE PROPERLY
...........................................................................................................................................
17
YELLOW FLAME.
.....................................................................................................................................................................................
18
FLASH BACK
............................................................................................................................................................................................
18
LOCATIONS OF SERIAL NUMBER
................................................................................................................................................................
19
PARTS LIST .......................................................................................................................................................................
20
EXPLODED ILLUSTRATION
.............................................................................................................................................
21
LIMITED WARRANTY
.......................................................................................................................................................
22
REGISTER/NG YOUR GRILL
...................................................................................................................................................................
22
. READ THE FOLLOWING INSTRUCTIONS CAREFULLY AND BE SURE YOUR GRILL IS PROPERLY INSTALLED, ASSEMBLED AND
CARED FOR. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE.
IF YOU HAVE QUESTIONS CONCERNING ASSEMBLY OR OPERATION, CONSULT YOUR DEALER, GAS APPLIANCE SERVICE
REPRESENTATIVE OR YOUR GAS COMPANY.
· NOTE TO INST ALLER:
LEAVE THESE INSTRUCTIONS WITH THE CONSUMER AFTER INSTALLATION.
· NOTE TO THE CONSUMER:
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE .
. THIS OUTDOOR COOKING GAS APPLIANCE IS NOT INTENDED TO BE INSTALLED IN OR ON RECREATIONAL VEHICLES AND/OR
BOATS.
*FOR WARRANTY PURPOSES, PLEASE RECORD YOUR MODEL NUMBER, SERIAL NUMBER, DATE OF PURCHASE & A COPY OF YOUR
RECEIPT OR INVOICE IN THE BACK
OF YOUR MANUAL ON PAGE 22.
Revision: 06/2015
f:1IJ♦
U

SAFETY INSTRUCTIONS
READ CAREFUL
L
Y BE ORE ASSEMBLY AND OPERATION O'E r¥0UR GRILL
WARNING:
Fuels used in gas or oil-fired appliances and the products of combustion of such fuels, contain chemicals known-to the State of
California to cause cancer, birth defects and/or reproductive harm. This warning is issued pursuant to California Health & Safety Code Sec.
25249.6.
THE LOCATION FOR YOUR GRILL
DO NOT use your gas grill in garages, porches, breezeways, sheds or other enclosed areas.
Your gas grill is to be used
OUTDOORS ONLY,
with at least
21 inches
clearance from the back and side of any combustible surface. The grill should not be placed under or on top of any surface
that will burn. Do not obstruct the flow of combustion and ventilation air around the grill housing.
PROTECT CHILDREN:
Keep children away from the grill during use and until the grill has cooled after you are finished. Do not allow children to
operate the grill.
WARNING! FOR YOUR SAFETY ...
-DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or
any other appliance.
-DO NOT store empty or full spare gas cylinders and/or chemicals under or near this or any
other appliance.
-Keep the fuel hose and electrical cord away from hot surfaces. Protect the fuel hose from
dripping grease. Avoid unnecessary twisting of the hose. Visually inspect the hose prior to each
use for cuts, cracks excessive wear or other damage and replace if necessary.
•
NEVER test for gas leaks with a lighted match or open flame.
-NEVER light grill with lid closed or before checking to ensure burner tubes are fully seated
over gas valve orifices.
-NEVER lean over cooking surface while lighting grill. Use barbecue tools with wood handles
and good quality insulated oven mitts when operating grill.
DANGER!
IF YOU SMELL
GAS ...
1. Shutoff gas to the appliance at its' source.
2. Extinguish any open flame.
3. Open grill lid to release any accumulation of fumes.
4. If gas odor persists, immediately contact your gas supplier or your fire department.
CHECKING FOR GAS LEAKS
NEVER TEST FOR GAS LEAKS WHILE THE GRILL IS LIT!
Prior to the first use and at the beginning of each new season (or, if using LP,
whenever gas cylinder is changed), it is a must that you check for gas leaks. Follow these steps:
1. Make a soap solution by mixing one part liquid detergent and one part water.
2. Turn off heat control valve(s), and then turn on gas at source.
3. Apply the soap solution to all gas connections: bubbles will appear in the soap solution if connections are not properly sealed. Tighten or repair
as necessary.
4. If you have a gas leak that you cannot repair, turn off the gas at the source, disconnect fuel line from the grill and immediately call your grill
dealer and gas supplier for professional assistance.
2
(f:1
11
,a

Your Natural Gas gri gnea to operate on na ural gas 0NLY, at a r.1ressure o " ater column (W.C.) regulateta_\the natural gas regulator
attached at the back of the grill. Check with your gas utility for local gas pressure and with your local municipalit or uili:ling code requirements.
Check with your gas utility or with local building codes for instructions to install gas supply line, or call a licensed and knowledgeable installer.
It is recommended that an "ON-OFF" shutoff valve be installed at the gas supply source:
-Outdoors after gas line piping exits outside wall or before gas line piping enters ground.
-Indoors in the branch fuel line in an accessible location near the supply line.
Pipe sealing compound or pipe thread tape of the type resistant to the action of natural gas must be used on all male pipe thread. Apply
compound or tape to at least the first three threads when making the connection.
Disconnect your gas grill from fuel source when the gas supply is being tested at high pressures. This appliance and its individual shutoff valve
must be disconnected from the gas supply piping system during any pressure testing of that system at pressures in excess of 1 /2 psig (3.5 kPa).
Turn off your gas grill when the gas supply is being tested at low pressures. This appliance must be isolated from the gas supply piping system by
closing its individual valve.
WARNING:
Gas valves are preset at the factory to operate on LP or natural gas. If you wish to convert to a different gas type, be sure to contact
your grill dealer, licensed plumber or authorized seNice center for further details. Conversion kits are not sold to the general public and require a
professional to perform seNice. Failure to properly convert a unit can cause serious injury to yourself and/or others, irreparable damage to your
grill and void of warranty.
SAFETY! BEWARE OF SPIDERS
CAUTION: BURNERS MUST BE INSPECTED AND CLEANED BEFORE FIRST USE.
Spiders and small insects occasionally spin webs or make nests in the burners during warehousing, transit and/or after long periods of non-use.
These webs can lead to a gas flow obstruction, which could result in a fire in and around the burner tubes. This type of fire is known as "FLASH-
BACK" and can cause serious damage to your grill and create an unsafe operating condition for the user. Although an obstructed burner tube is
not the only cause of "FLASH BACK" it is the most common cause, and frequent inspection and cleaning of the burners is necessary.
3
f:11JIU

Your propane gas grill is designed to be used with a standard 20 lb gas cylinder. In the United States, the gas cylinder must be constructed and
marked in accordance with specifications of the US Department of Transportation for Propane Gas Cylinders.
Always keep cylinder securely fastened in an upright position.
Never connect an unregulated propane gas cylinder to the grill.
Do not subject Propane cylinders to excessive heat.
CAUTION:
Never store a Propane gas cylinder inside a building or in the vicinity of any gas-burning appliance.
WARNING:
Gas valves are preset at the factory to operate on LP or natural gas. If you wish to convert to a different gas type, be sure to contact
your grill dealer, licensed plumber or authorized service center for further details. Conversion kits are not sold to the general public and require a
professional to perform service. Failure to properly convert a unit can cause serious injury to yourself and/or others, irreparable damage to your
grill and void of warranty.
SAFETY! BEWARE OF SPIDERS
CAUTION: BURNERS MUST BE INSPECTED AND CLEANED BEFORE FIRST USE.
Spiders and small insects occasionally spin webs or make nests in the burners during warehousing, transit and/or after long periods of non-use.
These webs can lead to a gas flow obstruction, which could result in a fire in and around the burner tubes. This type of fire is known as "FLASH-
BACK" and can cause serious damage to your grill and create an unsafe operating condition for the user. Although an obstructed burner tube is
not the only cause of "FLASH BACK" it is the most common cause, and frequent inspection and cleaning of the burners is necessary.
WARNING
•Do not store a spare or disconnected liquid propane cylinder under or near
this barbecue.
•A dented or rusty liquid propane cylinder may be hazardous and should be
check by your liquid propane provider.
•
Do not use a liquid propane cylinder with a damaged valve.
4

INSTALLATION INSTRUCTIONS
Your Built-in Gas Grill eomes to you fully assemblea. We str0ngly recommend professional installation a d ho,.gkup ft e Gas BBQ grill. These
instructions will provide you with the measurements necessary for you or your builder to construct a masonry s(ructure to house your outdoor gas
grill.
NOTE TO INST ALLER: Leave these instructions with the consumer for future reference. The grill must be installed in accordance with all local
building codes. Adapter from 1/2" NPT to BSP 21 mm & regulator are available from Bull dealers and distributors.
NOTE: Please remove the cotter pins from the burners before installing unit into an island. See page 10 for cotter pin removal.
SPECIFICATIONS FOR BARBECUE STRUCTURE
1. Your choice of masonry can be used for cabinet construction for the built-in gas grill; however it must be non-combustible material. Keep in
mind when choosing a location for your grill that it should NOT be located under any overhead combustible construction. Upper and lower level
vents must be provided for combustion air on both sides of built-in cabinet. Vents on BBQ insert must remain unobstructed to allow for combustion
air and ventilation. Upper vents must be located within 5 inches from the top of the island enclosure to the bottom of the vent. Lower vents must be
located within 1 inch from the bottom of the island enclosure to the bottom of the first vent openings and no more than 5 inches from the bottom of
the island enclosure to the top of the vent. If not using Bull vents, the vents you use must meet ANSI Standard codes. The upper vents must have
openings that have a total free area of not less than 1 sq in per lb of stored fuel capacity per vent and the lower vents must have openings that
have a total free area of not less than 1/2 sq in per lb of stored fuel capacity per vent. Both upper and lower vent openings must have minimum
dimensions so as to permit the entrance of a 1/8 in diameter rod.
TOP OF ISLAND ENCLOSURE
-- ,;-_fi_-
--1/'--
'
4 1/16
1/2
BOTTOM OF ISLANJ ENCLOSURE
2. The BBQ grill requires a wall opening of the following dimensions: See PAGES 7 & 8 for different models.
3. Place gas grill assembly into wall opening as shown in illustration on pages 7 & 8. BBQ rests on side and back edges of the BBQ insert.
4. For propane gas LP TANK STORAGE AREA MUST BE ISOLATED FROM GRILL AND VENTED.
5. Do not use any combustible materials for this construction. Minimum horizontal clearance to adjacent combustible surface from side and back of
the grill must be
21 inches. A 6 inch clearance is required behind grill to allow front portion of hood to open and for ventilation purposes.
5
t :11}!§,I)

INSTALLATION INSTRUCTIONS (CONT.)
CONNECTING O G'AS OURCE
�== =
._
the Gas BBQ.
IMPORT ANT: Before connecting grill to gas source, make sure BBQ Grill control knobs are in "OFF" position.
NATURAL GAS CONNECTIONS
IMPORTANT: Bull Outdoor Products does not recommend the use of any quick connect
fittings or lines to the unit. Use of these types of fittings or lines could cause low gas flow
and greatly reduce the performance of
the unit.
-Pipe sealing compound or pipe thread tape of the type resistant to the
action of natural gas must be used on all male pipe thread.
-Apply compound or tape to at least the first three threads when making the connection.
-Remove plastic cap from regulator installed on grill.
- Attach stainless steel flex line 3/8"/9.5 mm flare-female end to the regulator.
- Attached the other end of flex line to shut-off valve through a nipple.
-Attach a shut-off valve to gas supply pipe.
PERFORM GAS LEAK CHECK -REFER TO PAGE 2
PROPANE GAS CONNECTIONS
-In the United States, the LP gas pressure regulator and hose assembly supplied with this
unit must be used without alteration. If this assembly needs to be replaced, use only the
type 1 specified in the parts list supplied with this unit. Use a LP tank with a type 1 cylinder
valve.
-Outside the United States, the LP gas pressure regulator is not supplied with the grill but
Cavagna Group BS3016 Type 634PR regulator or equivalent can be purchased from Bull
dealers or hardware stores.
-Make sure the tank is firmly secured in an upright position.
-Turn the black coupling nut of the hose and regulator assembly in a clockwise direction.
-Make sure it is completely threaded onto the cylinder valve before turning gas supply on.
PERFORM GAS LEAK CHECK -REFER TO PAGE 2
6
GAS SUPPLY
(NOT PROVIDED)
l
SHUT-OFF VALVE I
NG REGULATOR (NOT PROVIDED) -I
(PROVID···E···D· )
'
\
l/.l
,,. smm"J
I
.
(NOi PROVIUtD)
NIPPLE & (/"
(NOT PROVIDED)\ w·"·
-
PRESSURE RELIEF
VALVE
- -/2
/',r
-
\ \ 8LEEDOFFVALVE
L LP REGULATOR .... (TURN CLOCKWISE
(PROVIDED) TO CLOSE)
f:ZIJ!U

INSTALLATION INSTRUCTIONS
(CONT.)
NOTE:
-Vents must be provided for combustion air and ventilation on both sides of built-in cabinet.
-When choosing a location for your gas grill keep in mind that it should never be located under any overhead combustible construction.
-The sides and back of the grill should not be any closer than
21 inches
to combustible construction.
-
DO NOT
store empty or full spare tanks under or near this or any other appliance.
-There must be a minimum of 6" counter space behind the grill in order to allow the grill hood to clear properly.
/
DsailA
OUTER LIPS OF GRILL RESTS
ON ISLAND CUTOUT EDGES
7
GRILL
NG GAS SUPPLY
(NOT SUPPLIED)
(f:11JtU

INSTALLATION INSTRUCTIONS
{CONT.)
)
NOTE:
-Vents must be provided for combustion air and ventilation on both sides of built-in cabinet.
-When choosing a location for your gas grill keep in mind that it should never be located under any overhead combustible construction.
-The sides and back of the grill should not be any closer than 21 inches to combustible construction.
-DO NOT store empty or full spare tanks under or near this or any other appliance.
-There must be a minimum of 6" counter space behind the grill in order to allow the grill hood to clear properly.
-The cylinder valve on the tank must be readily accessible for hand operation. The tank must be isolated enough to where it is shielded from
radiation, open flames and protected from foreign matter such as hot drippings.
-There must be access so the tank can be connected, disconnected, inspected and leak tested outside of the cabinet. As well access so that
connections which could be disturbed when installing the tank in the cabinet can be leak tested inside the cabinet.
\
\
LP �OSE
(Sl.?PU:':Di
Df-iail B
OUTER LIPS OF GRILL RESTS
ON ISLAND CUTOUT EDGES
8
GRILL
LP TANK
(NOT SUPPLIED)
NON-COMBUSTIBLE
CONSTRUCTION
(f:ZIJ!II

TANK RETENT
INSTALLATION INSTRUCTIONS (CONT.)
/
I
"-.
ION---..
I"--.{ -
"-
/
I !
I
to::
LI , = =n
1- L--
"'s:- ,-P-
TANK RETENTION SOLT
The tank retention system must be securely fastened to the bottom of the island with the use of bolts, washers and nuts. There must be a minimum
clearance of 2" between the floor and the cylinder enclosure. Once secured, place the LP tank in the tank retention system and tighten the tank
retention bolt until the tank is snug and cannot move.
l f l
l ! !
t t
!@=
BOLT
WASHER
TANK RETENTION
WASHER
l
�NUT
---y/\ __ ---- -..-,-.-,--rr---
TANK RETENTION BOLT
9

INSPECTING / CLEANING BURNERS AND GAS
VALVE O, IFICES )
CAUTION-Always turn off the gas supply prior to clearing your grill.
BURNER CLEANING
1. Remove burner from the grill insert (See drawing below). Bend a stiff wire (a light-weight coat hanger works well) into a small hook as shown to
the right. Run the hook through each burner tube and burner several times. c::J ,
REMOVE COTTER PIN
FROM CAST PEG BE�FORE -
LIFTING UP THE BURNER
/-- ·--
(
Detail C
2. Use a narrow bottlebrush with a flexible handle. Run the hook through each burner tube and burner several times.
3. Wire brush entire outside surface of burner to remove loose corrosion.
4. Clean any clogged hole with a stiff wire (such as an open paper clip).
5. Inspect the burner assembly for any openings caused by corrosion.
BURNER SHUTTER CLIP INSPECTION I ADJUSTMENT
The burners are set to a factory setting; however the air to fuel mixture may need to be adjusted to accommodate different gas pressures. In order
to adjust the air to fuel mixture, loosen the screw and rotate the shutter clip to the appropriate setting (see diagrams below). Tighten the screw and
repeat adjustment procedure to the remaining burners. This should improve burner efficiency.
SCREW
10
BURNER
SHlJTTER CLIP
(OPEN FOR LP)
SCREW

CAUTION-Always turn off the gas supply prior to clearing your grill.
1. Replace burner back into the grill insert. There is no need to replace the cotter pin back into the cast peg, ii is for shipping purposes only.
2. Check the burner for proper location after replacing.
Make sure the valve orifices are inside of the burner tubes (see drawing below). If the
valve orifices do not fit inside the burner tubes, lighting the burners may cause explosion and/or fire.
Detail D
ENSURE VAL VE ORIFICE
INSIDE BURNER TUBE
/GNITOR I ELECTRODE CHECK
Detail E
INSERT ASSEMBLY
CAST PEG ON BURNER
RESTS IN HOLE
With all control knobs set to "OFF", check each igniter individually for presence of spark at electrode. In turn, push each control knob in fully and
turn slowly about a 1/4 turn to the left (counter-clockwise) until a click is heard; the trigger hitting the strike block should produce a blue spark at the
electrode tip. Return control knob to "OFF" before checking next igniter.
BURNER OPERATION CHECK
NOTE: Upon first assembly the gas lines and burners will be full of air. In order for the burners to light properly the lines must fill with gas. It may
require several attempts at lighting the burners before you are successful.
1. With BBQ Grill control knobs in "OFF" position, turn on the Gas supply.
11

INSPECTING / CLEANING BURNERS AND GAS
AILVE ORIFICES {OON1.}
)
2. Light any burner by
fUShing its contro knob in fully and slowly (3 to 4 seconds) turning it,bout
V4 turn to the le nter-clockwise) until a
click is heard. The 3 to 4 second duration shoula proviae enough gas to lign! me burner. lftlie Burner does not light, immediately return the
control knob to "OFF", wait several minutes for the gas to disperse, and repeat the process. After burner lights saccessfullYi, turn control knob to
"OFF".
3. Repeat process for each control knob/igniter, in turn, ensuring that other knobs are in "OFF" position as you perform each check.
4. If any burners fail to light after several attempts, discontinue gas supply at source and re-inspect for obstructions to gas flow and orifices.
VALVE
INSPECT IGNITION ORIFICE
I
\,_
INSPECT BURNER ORIFICE
BURNER
INSPECT ALL PORTS
12
f:ZIJ!N

COOKING COMPONENT INSTALLATION
IMPORTANT: Before firs/use: wash flame laJers, c[king grids 1 and warming rack with wal, soapy water. Rinse and dry thoroughly. Season
metal surfaces with coo ing oiJ occasionally. (After cooking is completed, turn grill to high setting for NO MORE THAN five minutes to burn off
excess grease or food esidue)
CAUTION: DO NOT LEAVE GRILL UNATTENDED WHILE GRILL IS IN USE
1. Place stainless steel heat shields on lowest ledge under / between
burners in grill insert (see drawing to the right).
2. Place stainless steel flame tamers on lower ledge above burners in
grill insert (see drawing to the right).
3. Place cooking grids in grill insert on ledge above flame tamers
(see drawing to the right).
NOW YOUR GAS GRILL IS READY TO USE!
Before first use and at the beginning of each barbecue season:
1. Please read Safety, Lighting and Operating Instructions carefully.
2. Check gas valve orifices, burner tubes and burner ports for any obstructions.
3. PERFORM GAS LEAK CHECK -REFER TO PAGE 2.
13
Fl.AME FL.AME
TAMERS- -TAMERS

2. If your grill fuel source is a LP gas cylinder, check to see that cylinder is filled.
3. Check that the end of each burner tube is properly located over each valve orifice.
4. Make sure all gas connections are securely tightened.
TEST FOR LEAKS WITH A SOAP SOLUTION, NEVER WITH A FLAME.
(Gas Leak
Check instructions are on page 2).
5. Always open lid before lighting.
6. Set ALL BBQ Grill control knobs to "OFF" and open gas supply, LP cylinder or Natural Gas Valve.
7. Ignite only the burners you intend to use, using the same method for each: Push in control knob completely and rotate slowly (3 to 4 seconds)
about 1/4 turn to the left (counter clockwise) until a click is heard. The 3 to 4 second duration should provide enough gas to light the burner. If the
burner does not light, immediately return the control knob to 'OFF', wait several minutes for the gas to disperse, and repeat the process. After
burner ignites, repeat procedure with any other burner needed.
8. Adjust control knob(s) to desired cooking temperature.
NOTE:
If igniters fail to produce a spark at the electrode tip, burners can be manually lit with a fireplace-type match.
NOTE: To light gas grill with a fireplace-type match,
follow steps 1 through 6 above. Remove cooking grid and flame tamer from burner you
wish to light. Insert lighted fireplace-type match or long-necked butane lighter placing flame near to burner ports. Press in control knob and rotate
left to "HIGH" setting to release gas. Burner should light immediately. If more than one burner is needed, repeat procedure with each burner.
Replace flame tamer and cooking grid. Turn off burners not needed, and adjust other burners to desired cooking temperature.
OPERATING
PROCEDURE
Burn-off:
Before cooking on your gas grill for the first time, burn the grill to get rid it of any odors or foreign matter by igniting the burners, closing
the lid, and operating at "HIGH" setting for about five minutes. You may then either set the controls to "OFF" or cook on your grill immediately by
turning the control knobs to a lower setting.
CAUTION: DO NOT LEAVE GRILL UNATTENDED
WHILE IN USE.
Preheating:
It is necessary to preheat the grill for a short time before cooking certain foods, depending on the type of food and the cooking
temperature. Food that requires a high cooking temperature needs preheat for five minutes; food that requires a lower cooking temperature needs
only a period of two to three minutes. There is no need to preheat for casseroles or other foods that require slow cooking.
COOKING
TEMPERATURES
HIGH setting -Use this setting only for fast warm-up, for searing steaks and chops, and for burning food residue from the cooking grids after the
cookout is over.
MEDIUM setting -Use this setting for most grilling, roasting or baking, and for cooking hamburgers and vegetables.
LOW setting -Use this setting for all smoke cooking, rotisserie cooking, and when cooking very lean cuts such as fish.
Note:
These temperatures vary with the outside temperature and the amount of wind.
14

LIGHTING & OPERA TING INSTRUCTIONS (CONT.)
Cooking With Indirect �eat: You can cook poultry and large cuts o meat slowly to perfection on one side of the grill by indirect heat from the next
burner. The heat from ttie lightec
f
bumer circulates gently throughou the grill, cooking the meat or poultry wit out any direct flame beneath or below
the food you are prepqring. This method greatly reduces flare-ups when cooking extra fatty cuts, b cause there is no direct flame to ignite the fats
and juices that drip down during cooking. Place a drip pan slightly smaller than the cut of meat on tne cooking grids or flame tamer surface under
the meat being cooked. This will allow you to catch meat juices for making gravy.
,--··
Flare-Ups: The fats and juices that drip from the meat cause flare-ups. Since flare-ups impart the distinctive taste and color for food cooked over
an open flame, they should be expected and encouraged within reason. Nevertheless, uncontrolled flaring can result in a ruined meal. To control
excessive flare-ups caused by too high a heat setting, turn the heat control knob to a lower setting.
CAUTION: If burners go out during operation, close gas supply at source, and tum all gas valves off. Open lid and wait five minutes before
attempting to re-light (this allows accumulated gas fumes to clear).
CAUTION: Should a grease fire occur, close gas supply at source, turn off all burners and leave lid closed until fire is out. Do not use water or any
liquid to extinguish a grease fire.
CAUTION: Do not attempt to disconnect any gas fitting while your barbecue is in operation or while gas feed is on.
15
f:11Jfiil

CLEANING & MAINTENANCE
)
CLEANING THE COOK
After cooking, turn control knobs to OFF" and let grill cool bef re attempting to clean your cooking grids. Before ti st use and periodically it is
suggested that you wash the cooki g grids in a mild soap and warm water solution. You can use a washcloth or a vegetable brush to clean your
cooking grids. _____ ,,.. ----- ---- �
CLEANING THE FLAME TAMERS & HEAT SHIELDS
Washing the flame tamers & heat shields after every use is not necessary but periodically it is suggested you wash them in a soap and warm water
solution. Use a wire brush to remove stubborn burned on cooking residue. Dry the flame tamers & heat shields thoroughly before you reinstall it in
the cooking insert.
CLEANING
THE BURNERS
IMPORT ANT: Gas control knobs should be in the "OFF" position, and fuel line should be disconnected from gas valve manifold. To reduce the
chance of FLASHBACK, the procedure below should be followed at least once a month or when your grill has not been used for an extended
period of time.
1. Remove burners from grill by carefully lifting each burner up and away from gas valve orifice.
2. Wire brush entire outer surface of burner to remove food residue and dirt. Clean any clogged ports with a stiff wire such as an open paper clip.
3. Inspect the burner for damage (cracks or holes) and if such damage is found, order and install a new burner.
4. After installation, check to insure that gas valve orifices are correctly placed inside ends of burner tubes. Also check position of spark electrode.
CLEANING THE GREASE TRAY
The grease tray should be emptied and wiped down periodically and washed in a mild detergent and warm water solution.
ANNUAL CLEANING OF GRILL HOUSING
Burning-off the grill after every cookout will keep it ready for instant use. However, periodically the grill should be given an entire thorough cleaning
to ensure optimal performance.
1. Shut off gas supply at source and disconnect fuel line from gas valve manifold. Protect fuel line fitting.
2. Remove and clean (as explained above) the cooking grids, flame tamers and burners.
3. Remove warming rack and wash with mild detergent and warm water.
4. Cover the gas valve orifices with a piece of aluminum foil.
5. Brush the inside and bottom of the grill with a stiff wire brush, and wash down with a mild soap and warm water solution. Rinse thoroughly and
let dry.
6. Remove aluminum foil from orifices and check orifices for obstruction.
7. Check electrode as instructed on page 11.
8. Replace flame tamers, cooking grids, and warming rack.
9. Reconnect to gas source and observe burner flame for correct operation.
IMPORTANT: You should NOT line the bottom of the grill housing with aluminum foil, sand or any other grease absorbent substance. Grease will
not be able to drip down into grease collector and a grease fire could occur.
STAINLESS STEEL CLEANING AND MAINTENANCE
Stainless steel is a corrosion resistant chromium/nickel alloy steel that is both durable as well as strong with an outstanding luster. The goal of your
cleaning and maintenance routine should be to keep the stainless steel's protective chromium oxide layer intact. This is what prevents corrosion.
Contrary to popular belief, stainless steel is NOT rustproof, especially in the environment of a swimming pool. Chlorine, bromine, some fertilizers
and other elements are extremely caustic chemicals for stainless steel. These chemicals combined with heat and humidity greatly increase the
corrosiveness of these chemicals. Regular cleaning is the best way to prevent corrosion and add years of enjoyment to your Bull stainless steel
products.
16

TROUBLESHOOTING
IF GRILL FAILS
If grill still fails to operate properly,
TURN "OFF" GAS AT SOURCE, TURN CONTROL KNOBS TO "OFF",
wait for grill to cool, and check the
following:
a. Misalignment of burner tube(s) over orifice(s)
CORRECTION:
Reposition burner tube to properly seat over orifice.
b.
Obstruction in gas line
CORRECTION:
Remove fuel line from grill. DO NOT SMOKE! Open gas supply for one second to blow any obstruction from fuel line. Close off gas
supply at source and reconnect fuel line to grill.
c. Plugged orifice
CORRECTION:
Remove cooking grids, flame tamers and grease tray. Remove burners from bottom of grill insert by pulling cotter pin from
beneath burner peg using a screwdriver or needle nose pliers (Please reference the diagram on page 10). Carefully lift each burner up and away
from gas valve orifice. Remove the orifice from each burner up and away from gas valve and gently clear any obstruction with a fine wire. Re-install
each orifice, reinstall burners over orifices and seat each burner peg into mounting bracket at bottom of grill insert. There is no need to replace the
cotter pins, they are for shipping purposes only. Replace cooking components and grease collectors. If an obstruction is suspected in gas valve(s)
or gas valve bracket, please contact your gas grill dealer or gas appliance service person for assistance.
---
------.....
Detail F
d. Misalignment of igniter on
burner
CORRECTION:
Check for proper position of electrode tip. The tip of the electrode should be pointing forward toward the front and free from grease
for spark discharging. The ignition wire should be firmly connected to the valve ignition and electrode. Replace the ignition wire if the wire were
broken or cracked. With gas supply closed and all control knobs set to "OFF", check each positive igniter individually for presence of spark at
electrode. In turn, push each control knob in fully and rotate about 1/4 turn to the left (counter-clockwise) until click is heard; the trigger hitting the
strike block should produce a blue spark at the electrode tip. Return control knob to "OFF" before checking next igniter.
If re-ignition is necessary
While the gas grill is still hot, you must wait for a minimum of five minutes before commencing to re-ignite (this allows accumulated gas fumes to
clear). If all checks/corrections have been made and gas grill still fails to operate properly, consult your grill dealer or gas appliance service person.
17

FLASH BACK
When fire occurs in and around the burner tubes, immediately turn off gas at its source and turn the control knob(s) to "OFF". Wait until the grill has
cooled, then clean the burner tubes and burner ports as described on page 10.
18

LOCATIONS OF SERIAL NUMBER
Essential information about your product i encoded in the serial umber of your grill. This in ormation wilJ.be required for all warranty claims,
ordering replacement parts and will identify any variations of your unit. It is extremely important that you record your eri al number and register
your grill from the Pro°f Purchase. The serial number of your grill is located in the following areas:
ENO OF BOX
1. At the end of the box 2. Interior flap of the box
3. Reverse side of the grease tray 4. Left interior panel of the insert assembly
REVERSE SIDE
00000000000000000000000000000
19
LEFT INTERIOR PANEL OF
THE INSERT ASSEMBLY