Bull 88900 User manual

1
BISON PREMIUM CHARCOAL GRILL GRILL
CART OWNERS MANUAL MODEL #88900
USA Edition

2
READ THIS ENTIRE MANUAL CAREFULLY AND RETAIN FOR FUTURE REFERENCE
We care about your safety, so please….
BE SURE YOUR GRILL CART IS PROPERLY ASSEMBLED AND CARED FOR. FAILURE TO FOLLOW THESE
INSTRUCTIONS MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. IF YOU HAVE
QUESTIONS CONCERNING ASSEMBLY OR OPERATION, CONSULT YOUR DEALER OR APPLIANCE SERVICE
REPRESENTATIVE FOR ASSISTANCE.
NOTE TO ASSEMBLER, PLEASE RETURN THIS MANUAL TO CONSUMER AFTER INSTALLATION.
NOTE TO THE CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.
THIS GRILL CART IS NOT INTENDED FORUSE IN OR ON RECREATIONAL VEHICLES AND/OR
BOATS.
TABLE OF CONTENTS PAGE# 2
----------------------------------------------------------------------------------------------------------------------------------------------------------
HOW TO REGISTER YOUR GRILL CART
HOW TO ORDER GRILL CART REPLACEMENT PARTS ------------------------------------------------------------------------------- 3
BISON GRILL CART DETAILS
CART REPLACEMENT PARTS LIST / ILLUSTRATION -------------------------------------------------------------------------------------- 4
GRILL AND FASTENERS LIST FOR ASSEMBLY ---------------------------------------------------------------------------------------------- 5
CART ASSEMBLY INSTRUCTIONS ------------------------------------------------------------------------------------------------------------------ 5-7
CLEANING & MAINTENANCE ------------------------------------------------------------------------------------------------------------ 8
LIMITED WARRANTY POLICY ------------------------------------------------------------------------------------------------------------------------ 9-11
WARNING: THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS INCLUDING CARBON MONOXIDE
WHICH IS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER
REPRODUCTIVE HARM. FOR MORE INFORMATION VISIT: www.P65Warnings.ca.gov
v.2021.4.6

3
REGISTERING YOUR BISON GRILL CART
Your Bison Grill Cart is automatically covered by your Bull Limited Warranty if you have
completed the Warranty Registration Card for you Bison Grill within 90 days from the
Proof of Purchase. You may register your unit either online at www.bullbbq.com or by
sending in the completed hard copy along with a copy of the Proof of Purchase to:
Bull Outdoor Products, Inc., 1011 East Pine
Street. Lodi, California 94520 United States
ATTN: Warranty Service Center
LOCATION OF SERIAL NUMBERS
The essential information about your cart is encoded in the serial number of the Bison
Grill it was sold with. This information will be required for all warranty claims, ordering replacement parts and will identify any
variations of your unit. It is extremely important that you record your serial number and register your grill from the Proof of
Purchase. The grill serial number locations are shown below.
ON THE RIGHT SIDE OF YOUR BISON GRILL END OF YOUR BISON CART’S BOX OR INSIDE OF BOX FLAP
HOW TO ORDER REPLACEMENT PARTS
The following information is required before contacting your Bull Authorized Dealer to assure getting the correct part(s) for your Cart
Please refer to your owner’s manual parts list and illustration to identify what you need.
To Order Replacement Parts go to :https://www.bullbbq.com/buy-parts
Ordering Parts by phone: Bull is ready to help with two regional suppliers open 8:00 am to 5:00 pm Monday through Friday.
For the western region, please call Bull Grills & Spas at [phone]
For the eastern region. Please call Goodwood Hardware [phone]
IMPORTANT: Keep this assembly and operating instruction manual for referral, and for replacement parts ordering.
WARNING: Use of any part that is not factory authorized will void your warranty and may be dangerous.
FOR WARRANTY PURPOSES,
PLEASE RECORD OR RETAIN THE
FOLLOWING:
1) WARRANTY REGISTRATION
CARD FOR YOUR BISON GRILL
2) DATE OF PURCHASE
3) COPY OF YOUR RECEIPT OR
INVOICE

4
NOTE: PLESE COMPLETE THE FOLLOWING PRIOR TO ASSEMBLY:
1. Before attempting to assemble your grill cart, check that all the necessary parts are included by using the illustrated parts list.
2. Inspect parts for any damage and contact our service center or local dealer for replacement of any damaged parts.
3. Do not assemble or operate a grill cart that appears to be damaged.
4. For your safety, Bull recommends the assistance of another person when assembling larger and/or heavier items.
PARTS LIST AND ILLUSTRATION
88900 BISON PREMIUM GRILL CART PARTS LIST
ILLUSTRATION ID# BULL SKU # DESCRIPTION QUANTITY
1 88901 FRAME, CART BOTTOM 1
2 88902 SUPPORT LEG, FRONT, LEFT SIDE 1
3 88903 SUPPORT LEG, FRONT, RIGHT SIDE 1
4 88904 SUPPORT LEG, BACK, LEFT SIDE 1
5 88905 SUPPORT LEG, FRONT, RIGHT SIDE 1
6 88906 SCREEN, CART BOTTOM 2
7 88907 LEFT SIDE SHELF 1
8 88908 RIGHT SIDE SHELF 1
9 88909 SHELF HANDLE END CAP 4
10 88910 SHELF HANDLE CENTER BAR 2
11 16514 CART CASTER (WITH BRAKE) 4
1
2
3
4
5
6
7
8
9
10
11

5
CART FASTENERS FOR ASSEMBLY
Before attempting to assemble your grill cart, check that all the fasteners are included using the list
below.
If any are missing contact our Service Center, or local dealer for replacement.
88900 BISON CART ASSEMBLY HARDWARE LIST
ILLUSTRATION
ID #
DESCRIPTION, SIZE QUANTITY PURPOSE
12 ALLEN WRENCH (4mm) 1 ASSEMBLE HANDLES
TO SHELVES
13 HEX DRIVE BUTTON HEAD SCREW, M6
X 8 4
14 ALLEN WRENCH (5mm) 1
ASSEMBLE CASTERS
TO FRAME
15 HEX DRIVE BUTTION HEAD SCREW, M8
X 20 16
16 FLAT WASHER, 8mm 16
17 LOCK WASHER, 8mm 16
18 WRENCH (6mm) 1
ASSEMBLE SUPPORT
LEGS
TO FRAME
19 HEX DRIVE BUTTION HEAD SCREW, M6
X 12 16
20 FLAT WASHER, 6mm 32
21 LOCK WASHER, 6mm 32
22 HEX NUT, 6mm 16
CART ASSEMBLY INSTRUCTIONS
Do not assemble or operate a grill cart that appears to be damaged. For your safety, Bull recommends
the assistance of another person when assembling larger and/or heavier items.
STEP #1: ATTACH SHELF HANDLES TO SHELVES
Remove the pre-installed screws (M6X8 mm) on the handle end caps.
Per illustration below, combine the handle tube and end caps and then install the handle end
caps onto the side shelf.
SLIDE BOTH END CAPS AND
CENTER TUBE TOGETHER
WITH MOUNTING HOLES
APPROXIMATELY 13 ¾” APART
USE PROVIDED
ALLEN WRENCH
(ITEM 12) TO ATTACH 1
HANDLE TO EACH SHELF
USING 2 (ITEM 13) M6X8
SCREWS AS SHOWN

6
STEP #2 ATTACH CASTERS TO FRAME
Per illustration below, attach casters to pre-installed nuts on frame with provided fasteners and Allen
wrench.
STEP #3 ATTACH LEGS TO FRAME
Per illustration below, attach cart legs to on frame with provided fasteners and tools.
.
NOTE: EACH CART LEG IS UNIQUE AND MUST BE ASSEMBLED AS SHOWN TO ACCOMMODATE GRILL.
FRAME
,
ITEM 1
ITEMS 15, 16, 17
M8X20 SCREWS
8mm FLAT AND
LOCKWASHERS
4 FOR EACH CASTER
CASTERS, ITEM 11
ALLEN WRENCH
ITEM 15
ITEM 2
ITEM 3
ITEM 5
ITEM 4
SEE
DETAIL
ITEM 18
WRENCH
ITEMS 19, 20, 21
4 PER LEG
M6X12 SCREWS
6mm FLAT AND
LOCKWASHERS
ITEMS 20, 21, 22
4 PER LEG
M6 HEX NUT
6mm FLAT AND
LOCKWASHERS
ITEM 12
ALLEN
WRENCH

7
STEP 4: ATTACH GRILL TO CART LEGS
(This step will require at least 2 people).
1. Ensure the swivel casters are in the locked position in order to prevent the cart from moving and causing injury.
2. Remove the grill cooking and warming grates, briquet baskets and ash collector and place out of the way during
assembly.
3. NOTE: The cart back legs are attached with 4 specific fasteners that are already on your grill where shown
below. The cart front legs are attached with 5 specific fasteners. All of these fasteners are held by threaded
inserts pressed into the grill.
Remove those fasteners from the grill.
4. NOTE: (This step will require at least 2 people). Guide the cart legs around the outside of the grill head until
the cart leg mounting holes line up with the holes on the grill.
5. Install the mounting screws ‘finger tight’ on all four legs and evaluate alignment of the legs to the grill before
tightening. If using a torque wrench to install set it to 70 inch-pounds (8 Nm). Caution: cross threading will cause
irreparable damage to the cart.
STEP 5: ATTACH SHELVES TO GRILL
1. NOTE: The cart shelves are attached with 4 specific fasteners that are already on your grill where shown above.
All of these fasteners are held by threaded inserts pressed into the grill.
Remove those fasteners from the grill.
2. NOTE: (This step will require at least 2 people). Install one shelf at a time by having 1 person hold the shelf so
the mounting holes line up mounting holes on the grill. The shelves have slots on one side for hanging tools.
That side should be facing the front of the grill.
3. Install the mounting screws ‘finger tight’ on both shelves and evaluate alignment before tightening. If using a
torque wrench to install set it to 70 inch-pounds (8 Nm). Caution: cross threading will cause irreparable damage
to the cart.
Your grill cart is now completely assembled. Please continue to read the next section your Bison Grill to understand all safety, warning and
usage instructions for your Bison grill manual before use.
ITEM 2
ITEM 4
ITEM 7
FASTENERS ALREADY ON GRILL
INTENDED FOR MOUNTING CART
LEGS
FASTENERS ALREADY ON GRILL
INTENDED FOR MOUNTING CART
SHELVES

8
CLEANING AND MAINTENANCE
WARNING
BEFORE CLEANING YOUR CART MAKE SURE YOUR GRILL AND CART ARE COOL ENOUGH TO TOUCH.
CART CLEANING: Washing the cart is not necessary, but periodically it is suggested you wash the cart using
a soap and warm water solution. Use only a nylon brush to remove stubborn residue. Dry the cart before
the next use.
STAINLESS STEEL CLEANING AND MAINTENANCE
Stainless steel is a corrosion resistant chromium/nickel alloy steel that is both durable as well as strong
with an outstanding lustre. The goal of your cleaning and maintenance routine should be to keep the
stainless steel’s protective chromium oxide layer intact. This is what prevents corrosion. Contrary to popular
belief, stainless steel is NOT rust proof, especially in the environment of a swimming pool. Chlorine,
bromine, some fertilizers and other elements are extremely caustic chemicals for stainless steel. These
chemicals combined with heat and humidity greatly increase the corrosiveness of these chemicals. Regular
cleaning is the best way to prevent corrosion and add years of enjoyment to your Bull Stainless Steel
products.

9
Warranty Policy
LIMITEDWARRANTYONBULLOUTDOORPRODUCTS,INC.,PRODUCTS

THISLIMITEDWARRANTYGIVESYOUSPECIFICLEGALRIGHTS.YOUMAYALSOHAVEOTHERRIGHTS,
WHICHVARYFROMSTATETOSTATE.

THISLIMITEDWARRANTYCANALSOBEFOUNDONOURWEBSITEAT:
https://www.bullbbq.com/support-warranty(UnitedStatesCustomers);
https://www.bullbbq.eu/en/warrantyform.htm(InternationalCustomers)
ANDINTHEOWNER’S/INSTALLATIONMANUALTHATWEPROVIDEWITH
OURPRODUCT.

THISLIMITEDWARRANTYISSUBJECTTOTHEEXCLUSIONS,CONDITIONSANDLIMITATIONSSET
FORTHBELOW.

ANYIMPLIEDWARRANTIESIMPOSEDBYLAW,INCLUDINGWITHOUTLIMITATIONTHEIMPLIED
WARRANTIESOFMRECHANTABILITYANDFITNESSFORAPARTICULARPURPOSE,ARELIMITEDIN
DURATIONTOTHEDURATIONOFTHISEXPRESSLIMITEDWARRANTY.SOMESTATESDONOT
ALLOWLIMITATIONSONHOWLONGANIMPLIEDWARRANTYLASTS,SOTHEABOVELIMITATION
MAYNOTAPPLYTOYOU.

WHOMAYUSETHISWARRANTY?
BULL OUTDOOR PRODUCTS, INC. located at address 1011 East Pine St. Lodi, CA. 95240
("we") extend this limited warranty only to the consumer who originally purchased the product ("you") at
the original site of delivery or installation. It does not extend to any subsequent owner or other transferee of
the product. It does not apply to products installed in any rental, commercial or non-residential application.
Examples of excluded applications include, but are not limited to day care centers, schools, bed and breakfast
centers, churches, private clubs, fire stations, club houses, common areas in multi-family dwellings,
restaurants, hotels, nursing homes, food service locations and institutional food service locations.
WHATDOESTHISWARRANTYCOVER?
This limited warranty covers defects in materials and workmanship of the product and product components
identified below for the Warranty Periods defined below.

WHATISTHEPERIODOFCOVERAGE?
This limited warranty starts on the date of your purchase and lasts for the time period or time periods
specified above (the "WarrantyPeriod"). The Warranty Period is not extended if we repair or replace the
product. We may change the availability of this limited warranty at our discretion, but any changes will not
be retroactive.


10


Warranty Policy (Continued)
GrillWarrantyPeriods
The following parts are covered for oneyear on all our current gas grill models:
The lid, control panel, grease tray, bezels, knobs, temperature gauge, valves, regulator, flex tubes, rotisserie
burner, transformer, and all components of the lighting system.
The following parts are covered for threeyears on all our current gas grill models:
The manifold, handle end caps, flame tamers, heat shields, and warming rack.
The following parts are covered for lifetime on all our current gas grill models:
Insert assembly and the grates.
The warranty period for the grill burners vary by type:
Cast stainless steel burners - lifetime,
Welded burners – 5years, and
Porcelain coated burners – 3years.
The warranty period for the charcoal grill is oneyear on all parts, except for the insert assembly, which is
covered for 5years.
The Bel Air grill included a one‐year warranty on all parts.
ComponentWarrantyPeriods
All of the parts for our components/grill carts/refrigerators/kegerators/drawers/doors are covered for one
year with these exceptions:
Power Burner
oThe insert/grates are lifetime covered parts.
oThe manifold/burner are covered for 3years.
Searing Station/Slide in Double Sideburner
oThe grates are covered for lifetime,
othe insert for 5years, and
othe manifold for 3years.
Single Sideburner
oThe grates are covered for 5years and
othe burner for 3years.
Sidekick
oThe burner is covered for 3years.
PizzaOvens/Islands/FireFeaturesWarrantyPeriods
All of the parts and construction materials are covered for oneyear.
Grill Accessories and Grill Covers do not include a warranty period.