Bulldog Security Eco Net Controls EVC300 User manual

BULLDOG EVC300 QUICK
START
Bulldog EVC300 Controller QuickStart Guide - Rev_D - Master
EVC300
CONTROLLER
QUICKSTART
GUIDE

Bulldog EVC300 Controller
QuickStart Guide
1
CONTROLLER
Basic Controller Functions
Press to open or close Bulldog Motor.
Press to reset leak alarm.
Press to pair leak sensors, emergency stop buttons,
and remote buttons.

Bulldog EVC300 Controller
QuickStart Guide
1
Controller LEDs
LED above –Current System State
•(Green): System is armed and ready. Valve is open.
•(Red): System is armed and ready. Valve is closed.
•(Green, Red): Valve Motor is not fully closed, not fully
open, or the Valve Motor control wire is not
connected.
•(Green, Blue, Red): Your Bulldog Controller has
detected a leak and shutoff your water.
NOTE: Your water shutoff valve cannot be opened until the
leak alarm is reset.

Bulldog EVC300 Controller
QuickStart Guide
1
LED next to –Current Valve Controller Command
•(Red): Valve is set to open.
•(No Colour): Valve is set to closed.

Bulldog EVC300 Controller
QuickStart Guide
1
LED above –Wi-Fi Status
•(Solid Blue): Your Bulldog Controller is connected to
Wi-Fi.
•(Blinking Blue): Your Bulldog Motor is closed.
NOTE: To connect your controller to Wi-Fi, please see
your EVC300 Wi-Fi Connectivity Guide.

Bulldog EVC300 Controller
QuickStart Guide
1
Device pairing
NOTE: All devices included with your Starter Kit have
already been paired with your Bulldog Controller.
Pairing Leak Sensors
1. Press the button.
2. Place a leak sensor on a wet paper towel and allow it
to go through 2-3 beep cycles.
3. Once the Leak Sensor or Emergency Stop button is
paired, your Bulldog controller will enter an alert
state.
4. Clear the leak alert by pressing the Button.
5. Click button to re-open your water shutoff valve.

Bulldog EVC300 Controller
QuickStart Guide
1
Pairing Optional Remote Button
or Emergency Stop Button
1. Press the button.
2. Press and hold the Remote button.
Unpairing Devices
All paired devices can be removed by pressing and
holding the button for 5 seconds until the red LED
blinks.

Bulldog EVC300 Controller
QuickStart Guide
1
MAINTENENCE
Maintenance should be performed every 6 months to
ensure your device is armed and in working order.
Check Leak Sensor Battery
NOTE: Testing a Leak Sensors will trigger a leak alert.
1. Set your leak sensor on a wet paper towel.
2. Listen for the number of beeps.
•(2 beeps): Battery is charged.
•(3 beeps): Battery is low and needs to be replaced.
•(No beeps): Battery is dead, or leak sensor is not
properly being triggered.
•(Beeps but no leak alert): Leak Sensor is unpaired
or non-functional.
(Refer to section: Pairing Leak Sensors &
Optional Emergency Stop Button)

Bulldog EVC300 Controller
QuickStart Guide
1
Replace Leak Sensor Battery
1. Twist the leak sensor lid counterclockwise and lift.
2. Replace the battery with Type A23 12 Volt only.

Bulldog EVC300 Controller
QuickStart Guide
1
3. Line up alignment marks. Close and lock with clockwise
twist.
Check Bulldog Functionality
1. Close your bulldog water valve using the button.
2. Turn on the water at highest point in the building and
observe water flow after 10 seconds.
•(Water stops):Bulldog fully closes the valve.
•(Water continues running): Remove Bulldog from
water shutoff and follow Bulldog Mounting
Instructions card included with box.
3. Open your bulldog water valve using the button.

Bulldog EVC300 Controller
QuickStart Guide
1
SUPPORT

Bulldog EVC300 Controller
QuickStart Guide
1
Econet Support Email:
[e-mail]
Econet Support Phone:
[phone]
Leak Sensor Range Support Link:
https://www.econetshop.com/PDF/
SensorRange.pdf
Additional Support Page Link:
https://www.econetshop.com/
index.php/support/
Leak Sensor Pairing Video Link:
https://www.youtube.com/
watch?v=otzdhZbWBp4&t=146s
Bulldog EVC300 Controller QuickStart Guide –Rev_D