BURREL S22 User manual

Burrel S22 Trail Camera User’s Manual

1
PLEASE READ CAREFULLY BEFORE USING CAMERA
Package Contents
Camera Body and Ports
Mounting Strap
1
Trail Camera
1
Antenna
1
User’s Manual
1
Mic
Infrared
LED
Lens
Fresnel
Latch
Tripod Socket
Front Cover

2
Mounting Bracket
USB Port
TF card slot( Micro SD)
Nano SIM card slot
12V DC port
Menu Button
ON/OFF Switch
Battery compartments
Eject Button
Playback Button
Battery Bay A

3
Keys & Buttons
• MENU: Enter the program menu in preview mode
• ▲▼◄►: Move between the menu items and change the value
• OK:
o Save parameter settings in menu mode
o Play videos in playback mode
• Playback button : In live preview window, switch between
playback and preview mode
• Use Shortcuts: In live preview window,
o ▲ is the shortcut to choose Video mode, and
o ▼ is the shortcut for the Camera mode
o ◄ is the shortcut for Arm the camera(start working)
o ► is the shortcut for GPS information
o OK is for capture photos or record a video manually
• ON/OFF(Power) Switch: OFF in the bottom. ON in the top.
Battery Bay B

4
Quick Start
1. Make sure the power switch is at OFF position. Load the batteries into
the battery compartment according to the polarities indicated. Load a
set of 12 (recommended), 6(emergency, battery bay A or B) AA
batteries. Or connect 12V external power supply to the camera by
using the correct cable and external battery.
The following batteries can be used, make sure it is 1.5V AA.
• High-performance alkaline batteries
• Lithium batteries
• Rechargeable Ni-MH batteries
2. Insert a TF card (32GB or smaller). Open the camera and insert the TF
card into the card slot. Refer to the card symbol on the case for proper
orientation. The camera supports up to 32 GB TF card.
3. Insert a Nano SIM card.
4. Screw the antenna onto the antenna jack on the top of the camera.
Make sure it’s all the way in but DO NOT over tight it.
5. Slide the power switch to the ON position. The camera will enter the
live preview mode and start searching the network.
6. Wait until the camera finds the network. If the wireless carrier is not

5
found, you will need to go to the Advanced Wireless Setup section on
Page 10. If the wireless carrier is found, please go to the next step.
7. Press button to enter into the menu, then press ◄ or ►
buttons to move between the tabs (submenu) which contains different
group of items. Press the ▲ or ▼ buttons to activate the submenu
and edit different items. Press ◄► to change the value. Press the OK
button to save.
8. Navigate to the Wireless tab; scroll down to enter the submenus.
Change the Send Mode to Instant. Leave the Send To on Phone mode
if you are sending the MMS to a cell phone number. Or change to Email
mode if you are sending to your email address. Scroll down to Phone
or Email and input the phone number or email address of the recipient
there. Only Send Via=Internet available if choose Video mode.
9. Press button to exit from the submenu. Press the MENU
again to exit from setup menu and enter the live preview mode.
10. Press the OK button to capture image or record video manually.
11. At preview mode, press the playback button to playback. Use the ◄ or
► buttons to go through the images. Press ▲ or ▼ button to choose
magnification times. Press OK and press ◄ or ►,▲ or ▼ to move
the magnified area.
12. Press Playback button to exit. Magnification mode.
13. While reviewing the image, press button to delete the current
image or all the images.
14. Press Playback button to exit the playback mode.
15. Place the camera at the target area and turn on the camera (press the
left key ◄ for 1 second to arm the camera or slide the power switch to
ON（5 minutes later start to work）). The camera will take pictures or
videos as programmed. The height from the ground for placing the

6
camera should vary with the object size appropriately. In general, 3-6
feet is preferred.
16. If camera is working (Switch=on), it goes to setup mode when press
any button.
17. Push the power switch to the OFF position to power off the camera.
Please note that even in the OFF mode, the camera still consumes a
small amount of battery power. Therefore, please remove the batteries
if the camera is not in use for an extended time.
Menu Settings
Switch the camera to SETUP mode & press MENU. Press ▲▼◄► to
select the desired value, And then press OK to save.
Setting Items
Description
Camera
Mode
Choose to take Photo / Video/Photo&Video
Photo Size
Choose the image size, e.g. 3MP, 5MP,
8MP, 10MP ,12MP or 24MP.
Photo Burst
Choose the number of images taken after
each trigger (1-10).
Burst
Interval
Choose the interval time length between the
images taken in burst mode (Short 1/2/3s).
Video Size
Choose the video resolution.
Video Length
Set the video length to the desired duration.
Sound
Enable or disable video sound recording.
Trigger
Sensitivity
Select between High,Normal,Low,and OFF.

7
Trigger
Interval
The sleeping time after each trigger.
Time Lapse
Camera can be triggered by timer at a
preset time interval. Please note that even
in Time Lapse mode, the camera still can
be triggered unless the Sensitivity set to off.
Trigger
Start-Stop
1/2
The camera can be set to operate only at
specific time period. To enable this function
select ON and press ok. The start-stop
menu will then appear. This menu contains
the settings for times to start and stop as
well as the trigger interval and time lapse
interval. The start-stop setting will override
all other general camera settings. Since
there are 2 periods available, make sure to
not program times that overlap.
Work Day
Enable or disable the PIR trigger and Time
lapse trigger by day of the week.
System
ArmCamera
Make the camera working immediately.
Clock
Choose right timezone and press save.
Camera ID
Watermark in the left bottom corner of
image, up to 5 digits.
GPS
coordinate
Could be written to exif info of photo.

8
Camera
Tracker
Enable of disable camera tracker.
Password
This option allows a 6 digits password to be
set, keep it in mind. Recommend to use.
Time Stamp
ON /Off. Choose if the image stamp is to be
shown or not.
Overwrite
Cycle writing the TF card.
Beep
Enable or disable key tone
LED indicator
Enable or disable blinking of indicator.
FW Update
Start to update FW and MCU once update
files copied to TF card root directory.
System
Format
Format the TF card. This will erase all data
on the TF card. This cannot be undone.
Default
Restore all settings to factory default
values.
Language
Choose the menu language.
Information
Show Model Number, HW/FW/MCU version
and IMEI(wireless camera only).
Wireless
(wireless
camera only)
Send Mode
Choose to send the photo or video clips
instantly, or Daily report (send one picture
at preset time, save others) or turn off
sending. Both= Instant and Daily report.
Send Via
Choose to send the image via MMS (MMS
plan) or Internet (Data plan).
Send To
Send the images to Phone, Email or Both.

9
Phone
Input or revise the recipient Phone number.
Email
Input or revise the recipient Email address.
Image From
The text content of Image From will be
included in MMS/Email subject
Wireless
(wireless
camera only)
SMS
Control
Turning the SMS command function always
on or every n hours. On mode will increase
the power consumption.
Copy Para
Copy the current network parameter
settings to the TF card.
Update Para
If no pre-programmed carrier’s network
parameters, you will need to use the Setup
Tool to program in manually. After you use
the Setup Tool, a MMSCFG.bin file will be
generated and put on the TF card. You will
need to run Update Para to write the
settings to the camera.
Image Quality
Choose the wireless picture quality.
Debug Switch
Generate logs automatically when to set to
on. Press save to manually create logs.
Playback Button (Viewing Photo or Video)
• Switch to ON position
• Press Playback button to view the latest picture (or video).
• Press OK button to start playing the video clips.
• Press OK button to pause and press playback to quit playing.
• Press ◄ button to view the previous image and press ► button
for the next.