BURWELL Elcometer 7410 User manual

English
Elcometer 7410
Concrete Moisture Meter
Operating Instructions
7410_TMA_0354_Issue_03.fm(19520).fm Page -1 Friday, June 5, 2009 3:08 PM
Product Manual
7410 Concrete Moisture Meter
For more information: 1300 287 935 / [e-mail] / www.burwell.com.au
Copyright 2016 Burwell Technologies

R
English
The product meets the Electromagnetic
Compatibility Directive.
The product is Class A, Group 1 ISM equipment
according to CISPR 11.
Group 1 ISM product: A product in which there is
intentionally generated and/or used conductively coupled
radio-frequency energy which is necessary for the
internal functioning of the equipment itself.
Class A product are suitable for use in all establishments
other than domestic and those directly connected to a low
voltage power supply network which supplies buildings
used for domestic purposes.
i s a registered trademark of
Elcometer Limited.
© Copyright Elcometer Limited. 2009.
All other trademarks acknowledged.
All rights reserved. No part of this Document may be
reproduced, transmitted, transcribed, stored (in a retrieval
system or otherwise) or translated into any language, in
any form or by any means (electronic, mechanical,
magnetic, optical, manual or otherwise) without the prior
written permission of Elcometer Limited.
Doc.No. TMA-0354 Issue 03
Text with Cover No: 19520
7410_TMA_0354_Issue_03.fm(19520).fm Page 0 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
2 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

1
R
CONTENTS
Section Page
1 About this gauge ......................................2
2 Getting started .........................................5
3 Taking a reading ......................................9
4 A guide to moisture testing ..................10
5 Maintenance ...........................................12
6 Accessories ............................................13
7 Technical specification .........................13
8 Related equipment .................................14
7410_TMA_0354_Issue_03.fm(19520).fm Page 1 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
3 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

2
R
hank you for your purchase of this Elcometer
7410 Concrete Moisture Meter. Welcome to
Elcometer.
Elcometer are world leaders in the design,
manufacture and supply of inspection equipment
for concrete and coatings.
Our concrete inspection products include a
comprehensive range of concrete, and civil
engineering inspection equipment. Our coatings
products cover all aspects of coating inspection,
from development through application to post
application inspection.
Your Elcometer 7410 Concrete Moisture Meter is
a world beating product. With the purchase of this
product you now have access to the worldwide
service and support network of Elcometer. For
more information visit our website at
www.elcometer.com
1 ABOUT THIS GAUGE
The Elcometer 7410 Concrete Moisture Meter is
an accurate and easy to use non-invasive
instrument for non-destructive measurement of
the moisture content of concrete.
The gauge is very easy to use; switch the gauge
on, press it against the surface and take a
reading from the dial.
T
7410_TMA_0354_Issue_03.fm(19520).fm Page 2 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
4 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

3
R
The analogue dial shows concrete moisture
content up to 6%. The dial also includes scales
which can be used for comparative or qualitative
moisture readings for gypsum and other floor
screeds.
Note: The Elcometer 7410 Concrete Moisture
Meter will not detect or measure moisture
through any electrically conductive materials
including metal sheeting or cladding, black
EPDM rubber or wet surfaces.
The Elcometer 7410 Concrete Moisture Meter is
not suited for taking comparative readings in the
concrete substrate through thick coverings such
as wood.
1.1 Features
• Sturdy plastic case
• Easy-to-use
• Reading ʻholdʼ facility
• Low battery indication
1.2 What the box contains
• Elcometer 7410 Concrete Moisture Meter
• Battery
• Soft storage case
• Calibration certificate
• Operating instructions
7410_TMA_0354_Issue_03.fm(19520).fm Page 3 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
5 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au
5 of 17

4
R
The Elcometer 7410 Concrete Moisture Meter is
packed in a cardboard and foam package.
Please ensure that this packaging is disposed of
in an environmentally sensitive manner. Consult
your local Environmental Authority for further
guidance.
To maximise the benefits of your new
Elcometer 7410 Concrete Moisture Meter
please take some time to read these
Operating Instructions. Do not hesitate to
contact Elcometer or your Elcometer supplier
if you have any questions.
7410_TMA_0354_Issue_03.fm(19520).fm Page 4 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
6 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

5
R
2 GETTING STARTED
2.1 Fitting a battery
Your Elcometer 7410 Concrete Moisture Meter is
powered by a single 9 V battery. The battery is
located in a battery compartment at the rear of
the instrument.
To fit the battery:
1. Using a small screwdriver, coin or key,
push back the tab of the battery
compartment cover. The cover will then lift
away.
2. Fit the battery taking care to ensure correct
polarity.
3. Replace the battery compartment cover.
When the battery is nearing the end of its useful
life both lights on the front of the gauge flash for
3 seconds whenever the gauge is switched on.
The battery must be replaced when this happens.
7410_TMA_0354_Issue_03.fm(19520).fm Page 5 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
7 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

6
R
2.2 The buttons
Your Elcometer 7410 Concrete Moisture Meter is
controlled by the two buttons on the front of the
instrument.
ON/
OFF:
Press once to switch the gauge on.
The gauge will beep and then switch
off automatically 10 minutes after the
last button press or change of
reading. The gauge can also be
switched off manually by pressing
the ON/OFF button once.
HOLD: Press once to hold the reading.
Press again to release the reading. If
the gauge switches off while the
reading is on hold, the reading will be
restored next time the gauge is
switched on.
7410_TMA_0354_Issue_03.fm(19520).fm Page 6 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
8 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

7
R
2.3 The lights
When the battery is nearing the end of its useful
life both lights flash for 3 seconds whenever the
gauge is switched on.
Top
light:
Starts to flash when the HOLD button
is pressed to hold a reading. Stops
flashing when the HOLD button is
pressed again to release the reading.
Bottom
light:
Illuminates when the ON button is
pressed and remains illuminated until
the gauge switches off.
7410_TMA_0354_Issue_03.fm(19520).fm Page 7 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
9 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

8
R
2.4 The dial
Top
scale:
Graduated from 0% to 6%. Use this
scale to obtain readings of concrete
moisture content.
Bottom
scales:
Graduated from 0 to 10 and 0 to 100.
Use these scales to obtain
comparative or qualitative moisture
readings for gypsum and other floor
screeds.
Note: The bottom scales do not
provide quantitative readings for
moisture content.
3
0
6
1
2
5
4
0
10
9
8
7
6
5
4
3
2
1
0
1
0
0
8
0
6
0
4
0
2
0
CONCRETE
% H 0
2
GYPS UM
FLOOR
SCREED
7410_TMA_0354_Issue_03.fm(19520).fm Page 8 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
10 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

9
R
3 TAKING A READING
Before you start, remove any dust or foreign
matter from the probes of your gauge. Ensure
that the concrete surface being tested is clean
and bare and free from dust, dirt or standing
water.
1. Switch on the gauge.
2. Press the moisture meter firmly against the
surface being measured ensuring that all
the spring-loaded probes on the rear of the
gauge are fully compressed.
The moisture content will be displayed on
the dial.
3. Wait for the position of the needle to
stabilise before taking a reading; press
HOLD to retain the reading on the dial if
required.
4. Repeat steps 2 and 3 a number of times
and record the highest value.
7410_TMA_0354_Issue_03.fm(19520).fm Page 9 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
11 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

10
R
4 A GUIDE TO MOISTURE TESTING
Drying time
Concrete must be allowed to dry to an adequate
level before applying coatings or installing sheet
material, tile, wood, etc. Manufacturers of these
coating systems and sheet materials generally
require moisture testing to be performed before
application on a concrete surface. Moisture
content measurement is one such method of
testing. Excessive moisture in or permeating from
concrete after application of a coating, or
covering with sheet material, can cause failures
such as condensation, blistering, delamination,
movement and general deterioration of the
finished product. There is also a risk of promoting
microbial growth.
No exact period can be specified for the drying
time of concrete as this is affected by
temperature and humidity as well as concrete
curing times and other factors. During the drying
period and prior to applying the coating or sheet
material, the concrete surface should be checked
regularly to monitor moisture content.
For best and most accurate results, tests should
be carried out after the environment in which the
concrete is located has been at normal service
temperature and humidity for at least 48 hours.
All artificial heating or drying equipment should
be turned off at least 96 hours before final
7410_TMA_0354_Issue_03.fm(19520).fm Page 10 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
12 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

11
R
readings are attempted, otherwise results may
not accurately reflect the amount of moisture
present or moisture movement in the concrete
during normal operating conditions.
Removal of covering materials
All covering materials, adhesive residue, curing
compound, sealers, paints etc., shall be removed
from the test surface prior to testing. The test
surface must be clean, bare concrete.
Observe all health and safety practices relevant
to cleaning and removal of these types of
materials. Removal of covering materials and
cleaning, if required, shall take place a minimum
of 48 hours prior to testing.
Use of water based cleaning methods that could
lead to elevated surface and/or sub-surface
moisture levels in the concrete are not
recommended, and testing after such treatment
could result in elevated readings.
No visible water in liquid form should be present
on the concrete at the time of testing.
Avoid testing in locations subject to direct
sunlight or sources of heat. Use of artificial aids
for accelerated drying of concrete is not
recommended. If they are being used it is
recommended they should be turned off at least
four days before taking final readings.
7410_TMA_0354_Issue_03.fm(19520).fm Page 11 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
13 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

12
R
5 MAINTENANCE
The Elcometer 7410 Concrete Moisture Meter is
designed to give many years reliable service
under normal operating and storage conditions.
Regular calibration checks over the life of the
Elcometer 7410 Concrete Moisture Meter are a
requirement of quality management procedures
e.g. ISO 9000 and other standards.
Follow the instructions given on the optional
calibration check plate (see “Accessories” on
page 13) to confirm whether your gauge is
calibrated correctly.
If your gauge does not meet calibration
tolerances, contact Elcometer or your local
Elcometer supplier.
The instrument does not contain any user-
serviceable components. In the unlikely event of
a fault, the instrument should be returned to your
local Elcometer supplier or direct to Elcometer.
The warranty will be invalidated if the instrument
has been opened.
Details of Elcometer offices around the world are
given on the outside cover of these operating
instructions. Alternatively visit the Elcometer
website, www.elcometer.com
7410_TMA_0354_Issue_03.fm(19520).fm Page 12 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
14 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

13
R
6 ACCESSORIES
Your Elcometer 7410 Concrete Moisture Meter is
complete with all the items needed to take
measurements.
The following optional accessory is available
from Elcometer or your local supplier:
Calibration check plate KT007410P001
(Instructions for use of the calibration check plate
are supplied with the plate.)
7 TECHNICAL SPECIFICATION
Measurement range: 0% to 6%
Accuracy: 0.5%
Resolution: 0.2%
Weight: 290 g (10.2 oz)
Dimensions: 155mm x 85mm x 43mm
(6.1" x 3.3" x 1.7")
Battery: 9 V, PP3/6LR61
a
a. Batteries must be disposed of carefully to
avoid environmental contamination.
Please consult your local environmental
authority for information on disposal in
your region.
Do not dispose of any batteries in fire.
7410_TMA_0354_Issue_03.fm(19520).fm Page 13 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
15 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

14
R
8 RELATED EQUIPMENT
Elcometer produces a wide range of concrete
and coatings inspection equipment. Users of the
Elcometer 7410 may also benefit from the
following Elcometer products:
• Elcometer Adhesion/Bond Strength Testers
• Elcometer Concrete Crack Microscopes
• Elcometer Concrete Covermeters
• Elcometer Concrete Test Hammers
For further information contact Elcometer, your
local supplier or visit www.elcometer.com
7410_TMA_0354_Issue_03.fm(19520).fm Page 14 Friday, June 5, 2009 3:08 PM
7410 Concrete Moisture Meter
16 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au

R
www.elcometer.com
THE NETHERLANDS
Elcometer NL
Newtonlaan 115
3584 BH Utrecht
Tel: [phone]
Fax: [phone]
email: [e-mail]
www.elcometer.com
GERMANY
Elcometer Instruments GmbH
Ulmer Strasse 68
D-73431 Aalen
Tel: [phone]
Fax: [phone]
e-mail: [e-mail]
www.elcometer.de
FRANCE
Elcometer Sarl
97 Route de Chécy
45430 BOU
Tel: [phone]
Fax: [phone]
e-mail: [e-mail]
www.elcometer.fr
ASIA & THE FAR EAST
Elcometer (Asia) Pte Ltd
896 Dunearn Rd
Sime Darby Centre #03-09
Singapore 589472,
Tel: [phone]
Fax: [phone]
e-mail: [e-mail]
www.elcometer.com
ENGLAND
Elcometer Limited
Edge Lane
Manchester M43 6BU
Tel: [phone]
Fax: [phone]
e-mail: [e-mail]
www.elcometer.com
USA
Elcometer Inc
1893 Rochester Industrial Drive
Rochester Hills Michigan 48309
Tel: [phone]
Toll Free: 800 521 0635
Fax: [phone]
e-mail: [e-mail]
www.elcometer.com
BELGIUM
Elcometer SA
Rue Vallée 13
B-4681 Hermalle /s Argenteau
Tel: [phone]
Fax: [phone]
e-mail: [e-mail]
www.elcometer.be
JAPAN
Elcometer KK
7F Toranomon MT40 Bldg. 5-13-1
Toranomon, Minato-ku
Tokyo 105-0001
Tel: [phone]
Fax: [phone]
email: [e-mail]
www.elcometer.co.jp
7410 Concrete Moisture Meter
17 of 17For more information / 1300 287 935 [e-mail] / www.burwell.com.au