Bush DWFS146W Guide

246/3487

5-7
5
5
6
7
8
8-17
10
11
12-14
15
16-17
18
18
19
19
21
22
Specification
5
8-9
20
DWFS146W
2-3
4

910
246/3487
10 Drain pipe connector
9 Inlet pipe connector
4
DWFS146W
Eco

50
5

6

7

1
2
2kg
500ml
2
8
Salt consumption
When you run the dishwasher, the water
softener will be full of water. Therefore,
adding softening salt should always be
done immediately before you start the
unit. Check the salt level to ensure it is
enough before starting one of the
complete washing programs and ensure
500ml of water has been added.

The unit is equipped with a function that you
can adjust the frequency to release the salt to
the water softener. This is further to the
selector on the salt container. The default
setting is H4.
IMPORTANT :
YOU SHOULD SET THIS VALUE
ACCORDING TO THE WATER HARDNESS
ST
OF YOUR AREA BEFORE THE 1 USE.
INCORRECT SETTING WILL AFFECT THE
RESULT OF THE WASHING. ONCE YOU
HAVE SET THE SETTING, THE UNIT WILL
REMEMBER THE LAST SETTING.
Adjustment for value
1. Find out the hardness value for your tap
water or your area.
2. Compare with the table below to find out the
required value for setting to this unit.
Table
Frequency to
release salt
Value for
selecting in
this unit
Never
Always
Seldom
Often
Often
Sometimes
Sometimes
Usually
3. Close the door
4. Press ON/OFF button to turn on the
machine
5. Press Delay button and Program button at
the same time and hold for 5 seconds. The
machine will sound once. It displays H4.You
can release both buttons.
6. Continue to press Delay button to select the
desire value, i.e. H5, H6 or H7 is for serious
water hardness area region like UK.
7. Once the desire value is selected, press
Program button to confirm. Then the setting
has been stored and it will get back to the
normal standby status.
Hint : For easy setting on this value, it is
suggested to select H7. Then you can control
the salt consumption by turning the selector
on the salt container.
9

10

30
11

appliance
12

appliance
WARNING!
Do not let any item
extend through bottom
!
Cutlery tray
13

appliance
14

Standard daily cycle
for normally soiled loads,
such as pots, plates, glasses.
15

NOTE: Delay function:
After selecting the wash cycle program, you can set the desired delay time by pressing the delay
button. The dishwasher will start operation after the
selected delay time is elapsed.
It can be set up to 24 hour delay time.
table
NOTE: Child safety lock function
To lock, press child lock button and 3 in 1 button at same time and hold for at least 3 seconds.
The child lock indicator will flash 6 times and then illuminate.
To unlock, press child lock button and 3 in 1 button at the same time and hold for at least 3
seconds. The unit will get back to normal standby status and the child lock indicator will switch off.
If you open the door when washing, the machine pauses and sounds warning alarm, it displays E1.
Under different status, the program indicator will light in different combination:
1.
2.
3.
4.
5. Continue to press "program" button to select the desired "wash cycle". (See the section entitled
“ Wash Cycle Table”). Press "start/pause" button to start the program.
Then turn it on by press "power" button again,
Press "start/pause" button to start the washing program.
NOTE : "3 in1" function
"3 in 1" is a special designed program to use the 3 in 1 dishwasher tablet. You can buy the tablet
in the high street. Add the tablet into the detergent box and do not need to fill the salt & rinse-aid.
Press once on the 3 in 1 button and the indicator will illuminate. Then select the washing program
as usual. To have the best result, it is strong suggested to add salt to the salt container for water
softener. (see waster softener section)
Close the door,press the power button.
16

Special attention :
If all the indicator lights start to glimmer, the machine should be out of order. Please turn off the
power and shut down the water supply. Then call the customer helpline.
Warning :
It is dangerous and not recommend to open the door during the washing operation. The hot water
may come out and scald you while the door is open during the operation.
Program End
1.When the washing program is finished, it will sound 6 times and displays ''--''.
2. Open the door and remove all the dishes.
3.Turn off the unit by pressing the Power switch. Then close the door.
4. Shut down the water supply after using.
17

18

Error
19