www.buyersproducts.com
Phone (440) 974-8888
Fax 800-841-8003
—continue
Bill of Materials
1/2-13 Screw
1/2" Lock Washer
1/2" Flat Washer
Bracket with
Cushion
see Fig. 2
Anchor
Standard Mount Cont.
Fig. 3
Fig. 4
Fig. 5
1/2-20
Lock Nut
1/2"
Flat Washer
1/2"
Flat Washer
1/2-20 x 2-1/2"
Screw
KabGard with Mount Kit
Custom anchor for
trucks with tighter
hole patterns
Fender washers for
trucks with larger
slots. Apply vinyl
tape on surface
touching aluminum
body
Standard
anchor
ITEM PART NO. QT Y. DESCRIPTION
130 23 311 1KabGard, Weldment, Ford Style
13024357 1KabGard, Weldment, GM Style
23026704 1 Bracket PS Side, Weld Assy
33026703 1 Bracket DS Side, Weld Assy
43024035 1 Anchor Assy, Offset Right
53024036 1 Anchor Assy, Offset Left
63002723 2Anchor Assy
73003250 2Cushion Self-Adhesive
8FCS050020350 2 Screw, Hex HD Cap 1/2-20 x 3.5 GR .5, ZN
9FCS050013150 2 Screw, Hex HD Cap 1/2-13 x 1.5 GR .5, ZN
10 0150700 2 Nut, Center Lock Jam 1/2-20 GR A, ZN
11 3026019 2 Screw, HHC 1/2-13 x 4.00 Full Thread GR 5, ZN
12 FWL50088013 4 Washer, Lock - 1/2 Split, ZN
13 FWF050138014 8 Washer, Flat, 1/2" USS, ZN
14 3024340 2 Washer, Custom, 1.998OD x 0.530ID x 0.131THI
4. If side rail covers are installed, remove protective caps from
the front stake pockets or cut openings in the rail covers to
expose the front stake pockets. If present, drill holes in bedliner
walls to open access to front stake pocket side holes. Many
models of bedliners have a small mark on a wall against front
stake pocket. Use it to drill necessary holes.
Insert anchors into stake pockets. Make sure that the anchors’
long sides are facing inside the bed. Align holes in anchors with
stake pocket openings and install hardware loosely from inside
of the bed. For aluminum body truck, apply vinyl tape to the
steel Washers and Anchors to protect from premature corro-
sion. Apply only to surfaces touching the aluminum. See Fig. 4.
5. Position the Window Protector on the front wall of the truck
box. Slide the sides of Window Protector in the “U” shaped
guides of the brackets. Align the brackets’ slots with holes in the
Window Protector and insert 1/2-20 x 2-1/2" screws. Install lock
nuts. See Fig. 5
Position the Window Protector symmetrically on the vehicle.
Tighten lock nuts evenly on both sides to 60-70 foot-pounds.
Tighten screws on brackets until the lock washers are flattened
plus 1 - 1-1/2 turns. Overtightening these screws can result in
damage to truck’s sheet met al.
1/2-13 x 1-1/2" Screw
1/2" Lock Washer
1/2" Flat Washer
2
2
3
7
8
4
5
9
12
10
11
6
14
13
1
