Buyers Products Company SaltDogg 3014199 User manual

1
TM
WHITE WIRE-
BATTERY POSITIVE
BLACK WIRE-
BATTERY NEGATIVE
1
2
3
4
5
6 78
SINGLE RED
(16 AWG) WIRE-
CONNECT TO
12 VOLTS
KEYED ACCESSORY
INPUT WIRES
RED WIRE (10AWG) - BATTERY “+”
BLACK WIRE (10AWG) - BATTERY “-”
RED WIRE (16 AWG) IGNITION “+”
OUTPUT TERMINALS/WIRES:
A - BROWN (20 AMP FUSE) - LIGHT
B - RED - AUGER POSITIVE
C - GREEN - AUGER NEGATIVE
D - BLACK - VIBRATOR NEGATIVE
E - GRAY (30 AMP FUSE) - VIBRATOR POSITIVE
F - YELLOW - SPINNER POSITIVE
G - BLUE - SPINNER NEGATIVE
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone [phone] • Fax [phone]
Toll-Free Fax [phone] • saltdogg.com
Installation Instructions
3014199 SHPE Spreader Controller
Buyers Products Company is assumes no responsibility for installations not made in accordance with these instructions.
NOTE: Always disconnect battery before attempting to install
electrical components on your vehicle.
1. Mount the controller in a convenient location in the truck
cab. It is not recommended to mount the controller directly in
front of heat vents. Allow ample air space around controller.
2. Route both wire harnesses into truck cab through firewall
(it maybe necessary to drill holes). Insulate hole to avoid
water leaks. Insure no wires are nicked or damaged during
installation.
IMPORTANT!
Before installation, check your truck's battery and alternator
using load tester. Do not proceed to installation if truck elec-
trical system does not function properly.
3. Connect the round connecter on the wire harness to the
control box.
4. Connect the 2-pin rectangular connector on the power
cable to the control box.
5. Connect ignition wire to 12 volts keyed accessory (12VDC
positive).
6. Lay out a path for the power cable to the battery, use
quick ties to secure power cable.
DO NOT CONNECT TO BATTERY AT THIS TIME!
7. Lay out path for wire harness to the rear of the vehicle.
Stay clear of the exhaust system. Excess heat can damage
the wire harnesses. Use quick ties to secure harness to
underbody.
8. Connect the wire harness to the motors and vibrator.
9. Connect white wire to battery positive terminal. Connect
black wire to battery negative terminal.
THIS IS A WIRE GROUND ELECTRICAL SYSTEM! NO
CONNECTIONS TO TRUCK’S FRAME OR BODY ALLOWED!
In trucks with dual battery systems always connect power
cable to primary battery (larger capacity/ truck starting
battery).
CAUTION!
Do not mount controller in the way of air bag deployment!
Parts List
1 3014199 1 CONTROLLER, SHPE, SALT DOGG
2 3006842 1 POWER CABLE, CONTROL BOX
3 3006724 1 WIRE HARNESS, MAIN
4 3006753 1 WIRE HARNESS, CHUTE
ITEM PART NO. QTY dEscRIPTION
5 3006833 1 GEAR MOTOR 12 VDC. SPINNER
6 3006844 1 WIRE HARNESS
7 3009995 1 GEAR MOTOR, AUGER SHPE
8 3007416 1 VIBRATOR 200 LBS 12 VDC
ITEM PART NO. QTY dEscRIPTION

2
TM
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone [phone] • Fax [phone]
Toll-Free Fax [phone] • saltdogg.com
3019470 Rev. A
WARRANTY
Buyers Products Co. warrants all truck/trailer hardware manufactured or distributed by it, to be free from defects in material and
workmanship for a period of one year from date of shipment. Parts must be properly installed and used under normal conditions.
Any product which has been altered, including modification, misuse, accident or lack of maintenance will not be considered under
warranty. Normal wear is excluded. The sole responsibility of Buyers Products Co. under this warranty is limited to repairing or replacing any part
or parts which are returned, prepaid, and are found to be defective by Buyers Products Co. Authorization from Buyers Products Co. must be obtained
before returning any part. No charges for transportation or labor performed on Buyers’ products will be allowed under this warranty.
Controller Operation
1. To start spreader, be sure that truck engine is running to prevent battery from discharging. Flip power switch to ON
position. Controller switches will illuminate. Auger and spinner motors will start with full speed for a short time (displays
will show 9) and then drop to the speed settings selected.
2. To adjust speed simply rotate speed knobs until desired speed number is achieved.
3. To activate vibrator flip the Vibrator switch to ON position. Vibrator switch will illuminate. To turn vibrator OFF flip switch
to OFF position.
4. To turn controller OFF, simply flip power switch to OFF position.
Controller Codes
SYSTEM STATUS SPEED
DISPLAY
SPINNER
DISPLAY SOLUTION
1POSITIVE WHITE WIRE DISCONNECTED FROM
BATTERY,IGNITION WIRE CONNECTED BLINKING BLINKING
CONNECT WHITE WIRE TO BATTERY
POSITIVE TERMINAL
2 AUGER MOTOR INTERNAL FUSE IS BLOWN F REPLACE FUSE, CHECK FOR SHORT
CIRCUIT IN HARNESS, MOTORS
3 SPINNER MOTOR INTERNAL FUSE IS BLOWN F REPLACE FUSE, CHECK FOR SHORT
CIRCUIT IN HARNESS, MOTORS
4 VIBRATOR INTERNAL FUSE BLOWN U F REPLACE FUSE, CHECK FOR SHORT
CIRCUIT IN HARNESS, VIBRATOR
5 SPINNER MOTOR DISCONNECTED P CONNECT MOTOR, CHECK WIRE
HARNESS, MOTOR CONNECTORS"
6 AUGER MOTOR DISCONNECTED A CONNECT MOTOR, CHECK WIRE
HARNESS, MOTOR CONNECTORS"
7 SPINNER MOTOR OVERLOADED "SPEED NUM-
BER" BLINKING CLEAR OVERLOAD SOURCE
8 AUGER MOTOR OVERLOADED
REVERSE
CYCLING, THEN
SHOW SPEED
NUMBER
BLINKING
CLEAR OVERLOAD SOURCE
9VIBRATOR DISCONNECTED, VIBRATOR EXTERNAL
FUSE BLOWN U CONNECT VIBRATOR, REPLACE FUSE
10 LOW VOLTAGE (LESS THEN 10 VOLTS FOR 10
SECONDS OR MORE) L TEST TRUCK ELECTRICAL SYSTEM WITH LOAD TESTER
11
TRUCK BATTERY VOLTAGE FLUCTUATION "L" BLINKING "O" BLINKING TEST TRUCK ELECTRICAL SYSTEM WITH
LOAD TESTER
12 INSIDE TEMPERATURE OVER 70C (158F) C RELOCATE CONTROLLER TO HAVE GOOD
AIR CIRCULATION
13
WIRE HARNESS SHORT, AUGER MOTOR SHORT,
SPINNER MOTOR SHORT H H REPLACE SHORTED COMPONENTS
14 WIRE HARNESS MOTOR END, OR MOTOR SHORT "SPEED"
BLINKING
INSPECT FOR JAMS. IF NO JAMS FOUND, CHECK
MOTOR HARNESS CONNECTORS FOR SHORT.