BVI Endo Optiks E2 User manual

Endo Optiks®
E2 Laser Endoscopy System
Quick Setup Guide
For Technical Assistance: 732-530-6762
endooptiks.com I bvimedical.com

E2 Setup Steps
1 2 3
Color Video Monitor:
Turn monitor ON
Back of E2 Unit:
Turn Power ON
Back of E2 Unit:
Laser key in the 1 position
Quick Setup Guide
2
1
Setup Endoscope Handling Troubleshooting
3
endooptiks.com

BVI, BVI Logo and all other trademarks are property of Beaver-Visitec International, Inc. (BVI) © 2018 BVI
Troubleshooting Endoscope Handling Setup
Quick Set-Up Guide
E2 Front Control Panel
1Illumination: PLUG IN
2
Video Connection: Press video coupler
lever, plug in endoscope and release
lever/clip for a rm connection
3Laser: SCREW in connector
4Increase Illumination (Yellow arrows)
5Focus image by turning knurled ring on
video coupler
6Laser STOP Button: Ensure emergency
stop is in the OFF / OUT position
7Laser Power: Set to 0.25 watts
8Laser Duration: Set to CON (Continuous)
9Enable: PRESS
10 Aiming Beam: Set to 10 to 20
1
3
4 6
7 8
9
10
2
5
For Technical Assistance: 732-530-6762

Setup Endoscope Handling Troubleshooting
BVI, BVI Logo and all other trademarks are property of Beaver-Visitec International, Inc. (BVI) © 2018 BVI
Endoscope Handling
Step-by-Step Guide
1
Unpack the Endoscope
• Remove endoscope from shipping container
Note how the endoscope is packaged and coiled loosely
2
Prepare for Sterilzation
• Place endoscope in sterilization tray
• Make sure black connector caps are in place
• Do not coil the endoscope any tighter than 6” in diameter
3
Sterilize
• Steam autoclave (Caps must be in place) at 250°F (121°C)
for 15 minutes or 273°F (134°C) for 4 minutes
• Ethylene Oxide (Caps must be in place)
• Steris® & Sterrad®(Caps must be in place)
Note: Detailed Instructions are enclosed with endoscope
4
Remove from Sterilization Tray
• Uncoil endoscope carefully
• After autoclaving, caps may stick to connector ends
IMPORTANT NOTE:
Microendoscopes are made of glass. Do not pull, stretch, squeeze or bend any part of the endoscope.

BVI, BVI Logo and all other trademarks are property of Beaver-Visitec International, Inc. (BVI) © 2018 BVI
Troubleshooting Endoscope Handling Setup
Endoscope Handling
Step-by-Step Guide
5
Remove Caps
• Always hold microendoscope at metal connector
and lift edge of cap to break seal
• Gently work cap back and forth while pulling
• Do not grasp or pull on white jacket
6
Handle After Use
• Immediately after surgery, place microendoscope in the sterilization tray
• Replace caps; if caps are collapsed, discard and replace
• Clean tip
7
Clean the Tip
• Hold microendoscope between thumb and forenger,
approx. 1/4” from tip (See diagram 3)
• Clean tip with a moist instrument wipe then place directly on an instrument wipe
• While holding cannula or distal end (not hand-piece), gently run tip
across an instrument wipe in a circular motion
Note: Detailed instructions are enclosed with microendoscope
Diagram 3
endooptiks.com For Technical Assistance: 732-530-6762

Troubleshooting
Setup Endoscope Handling Troubleshooting
Problem Solution
Cannot adjust laser
settings on front panel
or unable to activate or
enable laser
Emergency STOP button is depressed;
release by turning to right
Turn laser key in rear of the unit to “1” position
Connect microendoscope; laser connector of endoscope must engage
and “beep” indicating laser is enabled
Connect footswitch
Display shows
777, 888, or FFF
Check that unit is plugged directly into wall socket or is the only item connected on the
surge protector
Make sure footswitch is connected
Re-start unit
Cannot focus image
Make sure connection to video coupler is secure; microendoscope should have “O” ring in
place and release clip on video coupler should be secure; engage with endoscope
Change microendoscope
For Technical Assistance: 732-530-6762

BVI, BVI Logo and all other trademarks are property of Beaver-Visitec International, Inc. (BVI) © 2018 BVI
Troubleshooting Endoscope Handling Setup
Problem Solution
Aiming beam
off-center or unclear
Remove endoscope from eye and clean tip
Make sure beam is bright and clear before re-entering eye
Illumination is
dimming
Check to see if your footswitch has light paddle controls (left and right inside). If left side is
inadvertently pressed, it will dim illumination. The right paddle will increase the illumination.
Note: Paddles in footswitch will override front panel control
Change microendoscope
NOTE If you have tried these recommended solutions and the problem persists,
please contact BVI Customer Service at 1-866-906-8080
Troubleshooting
Beaver-Visitec International, Inc.
500 Totten Pond Road – 10 CityPoint, Waltham, MA 02451
Customer Service: 1.866.906.8080 Fax: [phone]
endooptiks.com | bvimedical.com
Beaver-Visitec International, Ltd
85b Park Drive, Milton Park,
Abingdon, Oxfordshire, OX14 4RY, UK
Tel: [phone] Fax: [phone].595.761
For Technical Assistance: 732-530-6762