BXB Electronics BXB-C901 User manual

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
1
B
BX XB B‐ ‐C C9 90 01 1 
C
Co on nf fe er re en nc ce e I Im ma ag ge e P Pr ro oc ce es ss so or r 
U
Us se er r M Ma an nu ua al l 
V
V
Ve
e
er
r
rs
s
si
i
io
o
on
n
n:
:
: 1
1
1.
.
.0
0
0
D
D
Da
a
at
t
te
e
e:
:
: M
M
Ma
a
ar
r
rc
c
ch
h
h 2
2
28
8
8,
,
, 2
2
20
0
01
1
11
1
1

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
2
Contents .............................................................................................................................................................. 2
Overview ............................................................................................................................................................ 3
System Features .................................................................................................................................................. 4
Safety Instructions .............................................................................................................................................. 5
Operation and Features ....................................................................................................................................... 6
Front Panel Description ...................................................................................................................................... 6
Rear Panel Description ....................................................................................................................................... 7
Turn On .............................................................................................................................................................. 8
LCD Instructions ................................................................................................................................................ 9
System Operations & Settings .......................................................................................................................... 10
Mic Positioning ................................................................................................................................................. 10
Set Preset .......................................................................................................................................................... 11
Go Preset .......................................................................................................................................................... 12
Protocol Setting ................................................................................................................................................ 13
Video Jump Mode ............................................................................................................................................ 14
Gain Setting ...................................................................................................................................................... 15
Reset Settings ................................................................................................................................................... 16
Data Transfer through USB Port ...................................................................................................................... 17
Connection ........................................................................................................................................................ 18
Contents

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
3
Thank you for purchasing BXB-C901 Conference Image Processor from BXB Electronics
Co.
BXB-C901 is the latest conference image processor with superb performance and elegant
design which can be used in various conference rooms.
The advanced built-in digital control module provides compatibility of cameras such as
BXB and SONY… 128 preset points X up to 4 cameras make your conference system even
more powerful.
BXB-C901 is equipped with simplified keyboard; enables to control camera directions: up,
down, left, right, zoom in& zoom out.
High reliability is our utmost purpose when developing EDC1000 conference system.
Each main control unit and its fittings have all gone through careful assembly and strict test in
our ISO 9001 approved factory. The excellent performance, high reliability and reasonable price
make it the indispensable conference system for you.
Overview

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
4
1. The apparatus is equipped with a graphic LCD screen and 8 control buttons: up, down, left, right,
enter, return, zoom in& zoom out. You can operate the system on it without connecting keyboard.
2. RS485 and RS232 input connectors: comply with BXB FCS series (RS232 or RS-485 video camera
signal output, and BXB EDC series (2400 baud rate).
3. RS485 and RS232output connectors: comply with BXB and SONY… multi-brand cameras.
4. USB connector data transfer and BXB graphical control software.
5. There are 4 in and 6 out ports for images, in which the two (main-out) can be set for overcome and
individual display; the rest four correspondingly shows input1-> output1.
6. Each video input provides 4 sets of brightness GAIN value individual adjustment.
7. One microphone and camera preset point contrastive table, BXB-C901 supports up to 1009
microphones and four cameras.
8. Built-in simplified keyboard to control camera directions.
9. Camera preset point storage: 128 points for each camera, 4 cameras at most.
10. A 4-bit DIP switch settings (Reserved).
System Features

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
5
SafetyInstructions
1. Please read and observe these instructions before installing and using the apparatus.
2. Use only accessories specified by the manufacturer. The manufacturer is not liable for damage
caused by the use of non-specified accessories.
3. Install the apparatus and its accessories carefully. Strike and fierce shaking may damage the
apparatus.
4. Make sure the power cord is fixed properly.
5. Do not overload wall outlets and extension cords as this can result in a risk of fire or short circuit.
6. To reduce the risk of damage from lightning strikes, it is important that all electric cables should
be bonded to the same grounding point.
7. Do not block any ventilation openings to prevent overheating and malfunction.
8. Do not expose the apparatus to rain or moisture.
Humidity may lead inside components to damage. Appropriate shelter is necessary when placing
it outside (Best working environment: Temperature 0°C ~ 40°C <32°F ~ 104°F>, humidity below
90%).
9. Please do not switch on and off the apparatus rapidly.
Rapid switch on and off the apparatus should be avoided all the time to prevent inside sensitive
electronic circuits from being damaged by surges.
10. Do not clean the apparatus and its accessories with chemical solvents. Use only a clean,
dry/dampish cloth.
11. Refer to maintenance technician when the apparatus has been damaged in any way, such as:
A• power-supply cord or plug is damaged
B• liquid has been spilled in
C• has been exposed to rain or moisture
D• has been dropped
E• objects have fallen into the apparatus
F• does not operate normally
12. Note: When the printed circuit board is going through electric static treatment, correct ESD
safety precaution and grounding should be assured.
13. Note: Before connecting the apparatus to main AC, please select the supply voltage in
accordance with the wall voltage in your country to prevent damage. Refer to Installation and
Setting (Page 8) for selecting.
14. Warning: Do not disassemble or remodel the product, as these actions may lead to electrical
shock or damage. The guarantee on the product will become null if the product is ever
disassembled.

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
6
Front Panel Description
○
1Power indicator
○
224×2 bits LCD screen; shows current settings configuration
○
3Camera zoom out and speed adjustment
○
4Left, for camera direction and menu selection
○
5Down, for camera direction and menu selection
○
6Right, for camera direction and menu selection
○
7Enter, to save settings
○
8Camera zoom in and speed adjustment
○
9Up, for camera direction and menu selection
○
10 Return, to cancel settings and go back to top menu
Operation and Features

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
7
Rear Panel Description
○
1Power switch
○
2DC power input: in+ out-, DC 15V~20V (MAX)
○
3USB 2.0: USB port for PC connection
○
4Video output 1, for input 1 image
○
5Video output 2, for input 2 image
○
6Video output 3, for input 3 image
○
7Video output 4, for input 4 image
○
8Output Main 2
Video matrix output 2, output selectable; in override mode, operating camera or adjusting GAIN
will automatically switch to the image.
○
9RS485 Receiver
For BXB FCS conference main controller speed dome camera control terminal
○
10 RS232 Receiver:
For BXB FCS/ EDC conference main controller RS232 control terminal (jumper is essential)
○
11 RS485Transmitter: for camera control
○
12 RS232Transmitter: for camera control, RS-422 switchable with interface converter
○
13 ID: reserved 4 PIN DIP switch
○
14 Video output 1
○
15 Video output 2
○
16 Video output 3
○
17 Video output 4
○
18 Output Main1：
Video matrix output 1, output selectable; in override mode, operating camera or adjusting GAIN
will automatically switch to the image.
↓

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
8
Turn On
After confirming all the wiring is done, switch on the main controller and the LCD will display following
information
BXB SDC System
Ver 1.x
Later, the system will start auto-scanning to see if it operate normally
Memory Check
.....OK
Or not
Memory Check
.....ERR
After scanning completes, LCD will display following information (default page)
1.Mic Positioning
2 . S e t P r e s e t

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
9
LCD Instructions
1 Mic Positioning
2 S e t P r e s e t
3 Go Preset
4 P r o t o c o l S e t t i n g
5 V i d e o J u m p M o d e
6 G a i n S e t t i n g
7 R e s e t S e t t i n g s
1. Set microphone position (for image auto-track).
2. Set high-speed dome camera preset points.
3. Check t preset points above.
4. Set conference main controller type (input) and camera brand (output).
5. Set main output.
6. Adjust Gain values on each input screen.
7. Restore factorysettings.
Note: All figures shown on this manual is only for examples. Each main control unit has
been through a series of QC test before leaving factory. Default values are not identical,
users can change settings simply followed by the instructions below.
○
1

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
10
System Operations & Settings
Mic Positioning
Set auto-track preset points, 128 preset points for each camera and up to 4 cameras the most.
Press ▲or ▼, switch ◘to Mic Positioning, and then press Enter.
After entering, switch the cursor below MIC, press◄or ►to choose items; press ▲or▼to change value.
MIC - Mic Selection
No. 001-999 (※)are delegate mic, *1 - *10are chairman mics.
※In EDC series (set on menu 4.Protocol Setting), delegate mics are 001-127.
※If BXB FCS RS485 is input, following information will be shown.
S e t u p M I C p o s i t i o n o n
F C S m i a n c o n t r o l l e r
DOME - Camera Selection
No. 01-04
ADR - Preset Point Address Selection
No. 001-128 following after OFF
After setting, press Enter to save
S a v e . . . . . . . . O K
1 ◘M i c P o s i t i o n i n g
2 Set Preset
MIC DOME ADR
0 0 1 01 001
Mic Selection Camera Selection Preset Point Address

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
11
Set Preset
Set preset points, each camera provides 128 points and BXB-C901 supplies up to 4 cameras.
Press ▲or ▼, switch ◘to Set Preset, and then press Enter.
1 Mic Positioning
2 ◘Set Preset
After entering, press ▲or ▼to choose number, and then press Enter.
P r e s s ▲ ▼ t o choose
Came r a No : 001
After connecting, press▲, ▼, ◄, ►,, and to set image direction and size.
If camera output is Pelco-D (set on menu 4.Protocol Setting), 〝Pelco-D〞will be shown.
P r e s s ▲▼◄ ► to operate
Pan : 0000 T: 0000 Z: 0000
When disconnection occurs, following information will be displayed. It will get back to normal in three
seconds.
Dome i s none ex i s t
or timeout!
In Pelco-D, 001 is for camera rotation speed; 0-20 sets can be adjusted.
P r e s s ▲▼◄ ► to operate
Move Speed : 001
Press Enter to save preset point position, and then press ▲or ▼to set address no.
P r e s s ▲ ▼ t o choose
C a m e r a P r e s e t N o : 0 0 1
Press Enter to save.
Set Preset 001 . . . .OK
C a m e r a P r e s e t N o : 0 0 1
Horizontal coordinate Vertical coordinate Image magnification

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
12
Go Preset
On menu 3.Go Preset, you can check preset point you set previously quickly.
Press ▲or ▼, switch ◘to Go Preset, and then press Enter.
3 ◘Go Preset
4 P r o t o c o l S e t t i n g
Press ▲or ▼to choose camera number, and press Enter.
P r e s s ▲ ▼ t o choose
Camera No:001
Press ▲or ▼to choose preset point number.
P r e s s ▲ ▼ t o choose
C a m e r a P r e s e t N o : 0 0 1
Press Enter to move to the point.
G o P r e s e t 0 0 1 . . . . . . O K
C a m e r a P r e s e t N o : 0 0 1

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
13
Protocol Setting
Set conference main controller type (input) and camera brand (output).
Press ▲or ▼, switch ◘to Protocol Setting, and press Enter.
3 Go Preset
4 ◘P r o t o c o l S e t t i n g
Press ▲or ▼, switch ◘to Input/ Output, and then press ►to choose main controller type (input) and
camera brand (output)
1 ◘I n p u t : B X B F C S R S 2 3 2
2 O u t p u t : B X B D 7 0 1 P R E S E T
Press Enter to save.
Save . . . . . . . .OK

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
14
Video Jump Mode
Set Output Main1& Main2 video matrix output
Press ▲or ▼, switch ◘to Video Jump Mode, and press Enter.
5 ◘V i d e o J u m p M o d e
6 G a i n S e t t i n g
Press ▲or ▼, switch ◘to Output Main 1/ Output Main 2, and then press ►to set camera output
screen. (※)
1 ◘O u t p u t M a i n 1 : O v e r r i d e
2 O u t p u t M a i n 2 : D o m e 0 1
Press Enter to save.
Save . . . . . . . .OK
※
When Output 1/Output 2 is in Override mode, output screen displays according to the arrangement
on 1.Mic Positioning (MIC xxx, DOME1- DOME4, ADR xxx). If DOME1- DOME4 are all set, it will be
displayed by order.
When Dome01- Dome04 is selected, Output 1/ Output 2 output screen will be displayed individually.

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
15
Gain Setting
Brightness of each camera can be set individually. There is 0, 1, 2, and 3; in total 4 sets of brightness
are adjustable.
Press ▲or ▼, switch ◘to Gain Setting, and press Enter.
5 V i d e o J u m p M o d e
6 ◘G a i n S e t t i n g
After entering, press ◄or ►to select camera, press ▲or ▼to adjust brightness (0-3).
VIDEO IN: 1 2 3 4
C H G a i n : 0 1 2 3
Press Enter to save.
Save . . . . . . . .OK

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
16
Reset Settings
Reset to factory setting.
Press ▲or ▼, switch ◘to Reset Settings, and press Enter.
7 ◘Reset Settings
Press ◄or ►to select items you want to reset.
Selectable items:
1. MIC position (1.Mic Positioning on menu)
2. Camera preset points (2.Set Preset on menu)
3. All the preset points
P r e s s ◄►to choose i tem
( M I C ) P R E S E T A L L
Press Enter to confirm reset item, or press Return to cancel.
P r e s s E N T E R t o E R A S E
o r P r e s s R E T U R N t o E X I T
Clear all preset points.
Erase Memory
...........OK

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
17
Data Transfer through USB Port
Connect graphical control software on PC through USB port, you can have the data you set up on
main controller/ software work synchronically.
Data transfer rate (from PC to the main controller)
I N S P E E D D O M E S E T U P
P C - > M A I N ( 1 0 0 % )
Data transfer rate (from the main controller to PC)
I N S P E E D D O M E S E T U P
M A I N - > P C ( 1 0 0 % )

BXB ELECTRONICS CO., LTD.
Copyright © 2011 BXB ELECTRONICS CO., LTD. All rights reserved.
18
Connection
CAUTION:
．TOP REV EN T ELECT RI C SHOCK
DONOT REMOVE COVER(OR BACK)
．NOUSERSERVICEABLEPARTS
TOQ UALIF I ED SERVICE PERSONNEL
RISKOF ELE CTRIC SHOCK
DONOT OPEN
CAUTION
!
MADE IN TAIWAN
http://www.bxb.com.tw
SpeedDome
IOIOI
ConferenceLink
L.Spearer
Aux Output Mic InputAux Input
~ AC FUSE 250V T8 A DCF USE
D-D+
110
↓
15~20V
INPUT
CAUTION:
．TOPREVENTELECTRICSHOCK
DON O T REMOVE COVER(OR BACK)
．NOUSERSERVICEABLEPARTS
TO QUAL IFIE D SERVICE PERSONNEL
RISKOF ELECTRIC SHOCK
DONOT OPEN
CAUTION
!
MADE IN T AIWAN
http://www.bxb.com.tw
SpeedDome
IOIOI
ConferenceLink
L.Spearer
Aux Output Mic InputAux Input
~AC F USE 250V T8A DCF USE
D-D+
110
↓
15~20V
INPUT
↓
15~20V
INPUT
CAUTION:
．TOPREVE N T ELECTRIC SHOCK
DONOTREMOVE COVER(OR BACK)
．NOUSE R SERVICEA BL E PARTS
TOQU AL IFIE D SERVICE PERSO NNEL
RISKOF ELECTRIC SHOCK
DONOT O PEN
CAUTION
!
MADEIN T AIWAN
http://www.bxb.com.tw
SpeedDome
IOIOI
Confere nce Link
L.Spearer
Aux Output
~AC FUSE 250V T8A DC FUSE
D-D+
110

BXB ELECTRONICS CO., LTD.
19
BXB Electronics Co., LTD. TAIWAN | Website: www.bxb.tw
PA System / Conference System / Language Laboratory System
TEL：[phone] FAX：[phone]