Byron Home EasyHE-203 User manual

Caution: always make sure the switch converter is
secure in the back box when programming.
Switch Converter
Up to Six remote control units can be paired with each converter switch or
module.To pair a converter switch, connect the converter unit as per the wiring
instructions. Using a small screw driver press "Learn" button.The LED will start
to flash; press the selected "ON" button on the remote control,the LED will stop
flashing.The units are now paired together, you can test this by pressing the
selected "On/Off" button.
Deleting Remote Control:
To delete a remote control that has been paired with a HomeEasy receiver
unit, press the "Learn".The LED will start to blink; press the "Off" button on the
remote control,the LED will blink twice to confirm that the remote control has
been removed from the receiver sockets memory.
Pairing/Deleting with Remote Control:
RE-INVENTING THE HOME
HOME
easy
HE-203 Remote Control
Switch Converter & Dimmer
V1.0 Installation:
The HomeEasy remote control Switch
Converter allows you to convert a
standard 1way light switch in to a
HomeEasy remote control unit.
For use with in series with incandescent
lighting only.
INSTALLATION WARNINGS:
BEFORE COMMENCING INSTALLATION
ISOLATE YOUR MAINS ELECTRIC SUPPLY
Read the instructions care fully before starting the installation process and keep
them for future reference. If you are in any doubt on the installation process,
consult a qualified electrician.
This product should be installed in accordance with the relevant sections of
the building
regulations code,and the current edition of the IEE Wiring Regulations
(BS 7671:Requirements for electrical installations) and appropriate statutory
regulations.
As of1 April 2004, new installations in the UK should be wired using the EU
harmonised colours for the supply conductors:
New colours:
 BROWN = Live  BLUE = Neutral Earth = Yellow/Green
Old colours:
 RED = Live BLACK = Neutral
The old colours will cease from April 2006.
Electrical installations in bathrooms, kitchens, gardens, floor and heating systems,
swimming
pools, saunas and extra-low voltage lighting are classed as special installations and
must
Do not install ceiling receivers on lighting circuits used to supply other
products such as extractor fans and shaver socket outlets.
Do not exceed the Maximum Power Rating of 210W,Incandescent lighting
only
Origional Switch
240V ~50Hz
Do not use the switch converter with low voltage lighting transformers,
fluorescent bulbs,and energy saving lighting or fans, incorrect installation may
damage the converter. In case of any doubt consult a qualified electrician.
1: Isolate the mains supply, then remove the existing switch and disconnect the
wiring from the switch terminals on the back of the light switch.
2: Ensure the wall box is free from plaster lumps, projecting screw heads or any
other material. The switch converter is designed to fit in a 25mm back box, if
required a deeper back box or a proprietary spacer can be used between the
switch and the wall.
3: Wire the mains cable to the converter switch as per the diagram below:
240V Input
L
4: Connect the two switching wires from the switch converter to the original
light switch, making sure 1 way operation is used.
5: Make sure all terminals and earth connections are correct and secure with
no bare wires showing.
You will now need to program the switch converter:-
L
Making sure the live cable is connected to " " terminal and,the switch live
wire to the " " terminal.
6: Gently replace the switch cover making sure no wires are caught between
the switch and the wall. Do not over tighten as this could crack or distort the
switch.
Reconnect the mains supply
Learn Button

C H Byron
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR
Contact Details:
433MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom. www.chbyron.com
A
B
DK
FIN
F
D
GR
LT
IRL
I
L
NL
P
E
S
UK
BG
CZ
EST
H
IS
LV
M
N
SK
SLO
CH
PL
RO
0560
Tel: [phone]
Fax: [phone]
Web: www.chbyron.com
E-mail:
[email protected]
Help: Occasionally interference from receiver sockets plugged into adjacent wall
sockets or when used with transformers (low voltage products) can affect the
operating range.
Try placing one of the receiver sockets in another wall socket. For low voltage
products place the transformer as far away form the receiver socket as possible.
Contact:   Helpline: 0845 2301 231
TIMBER CONCRETE
METAL GLASS
PLASTICS
RF Range: :The radio signals operating distance is reduced when the signal has
to pass through walls.The radio signals achieve a range of 30m inside a building;
this can be reduced depending on the type of material
10 - 15%
BRICK
10 - 40%
40- 80%
10 - 40%
90% 5 - 15%
Range
Reduction Guide:
Switching On/Off /Dimming:
Help Section :
Product Specification:
Switch Converter: HE-203
Power: 230V ~50Hz
Max Load 210W (Incandescent Lighting)
Internal Fuse:2A, 130 degrees Celsius
Range: 30 Metres (Open Distance)
Frequency: 433.92MHz
Indoor Use Only
Warning: Never Exceed the Product Specification
OFF
ON
Remote Control:
On: Press on button
OFF: Press Off button
(See pairing/deleting with remote control)
1
2
Remote Socket reset:
To delete all the remote control units from the memory of the receiver socket,
hold the "Learn" button for more than 6 seconds, the LED will start to blink
continuously. Press the learn button again, the LED will blink twice to confirm
the deletion of all remote controls form the receiver memory.
Dimming: Press "On" and then press "On" again,the converter unit will now
start to dim, press "On" to select the required level.To switch "Off",press off
as normal.
Standard Light Switch:
On/Off: Switch on and off as normal.
Dimming: Switch On, Off and On again.The converter will now start to dim, to
select the required level switch the light Off and On.