C.P. Electronics EBMPIR-MB-B User manual

PIR Sensor
Detects movement within the unit’s detection range,
allowing load control in response to changes in occupancy.
Front view
PIR lens
which covers...
PIR sensor
Overview
The EBMPIR-MB-B miniature PIR (passive infrared)
presence detector provides automatic control of lighting
loads. It is specifically designed for mounting onto a batten
style luminaire.
The detector will switch incandescent, fluorescent, compact
fluorescent and LED lighting.
The unit detects movement using a PIR sensor and turns
the load on. When an area is no longer occupied the load
will switch off after a 10 minute time out period.
Features
Product Guide
Cables to luminaire control gear
Batten mount PIR detector
EBMPIR-MB-B

2
Detection diagram
Range
Walk towardsWalk across
Height Range Diameter
7m 10m
2.8m 5m
Height Range Diameter
7m 16m
2.8m 9m
Note: illustration shows an average of the walk across and walk towards figures below.
 When power is applied to the unit, the load will turn on immediately.
 For the first 5 minutes of operation the time out period is 10 seconds to aid commissioning.
 Vacate the room or remain very still for more than 10 seconds and wait for the load to switch off.
 Check that the load switches on when movement is detected.
 When the 5 minutes have elapsed the time out will be 10 minutes.
Power-up test procedure
What if the load does not turn ON?
 Check that the live supply to the circuit is good.
 Check that the load is functioning by bypassing the sensor (e.g. link Land L/ Out).
What if the load does not turn OFF?
 Ensure that the area is left unoccupied for longer than the 10 minute time out period.
 Ensure that the sensor is not adjacent to circulating air, heaters or lamps.
Fault finding
Wiring diagram

3
Installation
Components
Standard luminaire fitting
IP luminaire fitting
Part Quantity
Supplied
IP Spacer with silicone coating 1
Silicone washer 1
5º washer 1
5º spacer 1
M20 nut 1
Mounting hole without key
Mounting hole with key
Note. Key to be at top of
sensor.
Note. Use the 5ºspacers
where the luminaire
housing has a draft angle.
Important
Ensure that the silicone washer and/or the IP spacer are used to maintain IP rating.
Do not grip unit at the lens end. Hold the square body near the threaded end when installing and tightening the
nut. Care must be taken to prevent damage to the lens and surrounding IP seal.

4
Due to our policy of continual product improvement CP Electronics reserves the right to alter the specification of this product without prior notice.
Dimensions See diagrams opposite.
Weight 0.10kg
Supply Voltage 230VAC +/- 10%
Frequency 50Hz
Maximum Switching Load 2 Amps fluorescent and incandescent
lighting.
2 Amps compact fluorescent lighting.
2 Amps low energy lighting.
2 Amps low voltage lighting (switch primary
of transformer).
Switch SON lighting loads via a contactor.
Power consumption On 799mW, Off 807mW
Cable specification 1m 1/1.13 solid core cable 105ºC
Temperature -10ºC to 50ºC
Humidity 5 to 95% non-condensing
Material Flame retardant ABS/PC
Type Class 2
IP rating IP65
Compliance EMC-2004/108/EC
LVD-2006/95/EC
Technical data
C.P. Electronics Ltd
Brent Crescent
London
NW10 7XR
United Kingdom
Tel: + 44 (0) 333 900 0671
Fax: + 44 (0) 333 900 0674
www.cpelectronics.co.uk
[email protected]
Ref: #WD601 Issue 3
FM 45789 EMS 534520
IMPORTANT NOTICE!
This device should be installed by a qualified electrician in
accordance with the latest edition of the IEE Wiring
Regulations and any applicable Building Regulations.