Cabletron Systems BRIM-A6 User manual

BRIM-A6
USER’S GUIDE
book Page 1 Thursday, April 18, 1996 2:18 PM

BRIM-A6 User’s Guide i
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information
contained in this document without prior notice. The reader should in all cases consult Cabletron
Systems to determine whether any such changes have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FORANY INCIDENTAL,
INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT
NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR
THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN
ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH
DAMAGES.
 Copyright 1996 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005
All Rights Reserved
Printed in the United States of America
Order Number: 9031311-01 January 1996
SPECTRUM , LANVIEW , MicroMMAC , and BRIM are registered trademarks and Element
Manager , EMM-E6 , EMME , EPIM , EPIM-A , EPIM-F1 , EPIM-F2 , EPIM-F3 , EPIM-T ,
EPIM-X , ESXMIM , FOT-F , FOT-F3 , HubSTACK , NBR-420/620 , SEH , SEHI , and TMS-3 are
trademarks of Cabletron Systems, Inc.
All other product names mentioned in this manual may be trademarks or registered trademarks of
their respective companies.
Printed on Recycled Paper
book Page i Thursday, April 18, 1996 2:18 PM

Notice
ii BRIM-A6 User’s Guide
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial environment.
This equipment uses, generates, and can radiate radio frequency energy and if not installed in
accordance with the operator’s manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause interference in which case the user
will be required to correct the interference at his own expense.
WARNING: Changes or modifications made to this device which are not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.
DOC NOTICE
This digital apparatus does not exceed the ClassA limits for radio noise emissions from digital
apparatus set out in the Radio Interference Regulations of the Canadian Department of
Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables
aux appareils numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique
édicté par le ministère des Communications du Canada.
VCCI NOTICE
This equipment is in the 1st Class Category (information equipment to be used in commercial and/or
industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference
by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial
and/or industrial areas.
Consequently, when used in a residential area or in an adjacent area thereto, radio interference may be
caused to radios and TV receivers, etc.
Read the instructions for correct handling.
book Page ii Thursday, April 18, 1996 2:18 PM

Notice
BRIM-A6 User’s Guide iii
CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT
IMPORTANT: Before utilizing this product, carefully read this License Agreement.
This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”)
that sets forth your rights and obligations with respect to the Cabletron software program (the
“Program”) contained in this package. The Program may be contained in firmware, chips or other
media. BY UTILIZING THE ENCLOSED PRODUCT,YOU ARE AGREEING TO BECOME
BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND
THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IFYOU DO NOT
AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED
PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.
CABLETRON SOFTWARE PROGRAM LICENSE
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this
package subject to the terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the
Copyright Act of the United States or as authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the
Program.
3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws
and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and
venue of the New Hampshire courts.
EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY
1. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in
writing, Cabletron makes no warranty, expressed or implied, concerning the Program (including
its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO
YOU BY CABLETRON IN WRITING, EITHER EXPRESSED OR IMPLIED, INCLUDING
BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO THE PROGRAM, THE
ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
2. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL
CABLETRON OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER
(INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS,
PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL,
INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)
ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT,
EVEN IF CABLETRON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR
ON THE DURATION OR LIMITATION OF IMPLIED WARRANTIES, IN SOME
INSTANCES THE ABOVE LIMITATIONS AND EXCLUSIONS MAY NOT APPLY TO
YOU.
book Page iii Thursday, April 18, 1996 2:18 PM

Notice
iv BRIM-A6 User’s Guide
UNITED STATES GOVERNMENT RESTRICTED RIGHTS
The enclosed product (a) was developed solely at private expense; (b) contains “restricted computer
software” submitted with restricted rights in accordance with Section 52227-19 (a) through (d) of the
Commercial Computer Software - Restricted Rights Clause and its successors, and (c) in all respects
is proprietary data belonging to Cabletron and/or its suppliers.
For Department of Defense units, the product is licensed with “Restricted Rights” as defined in the
DoD Supplement to the Federal Acquisition Regulations, Section 52.227-7013 (c) (1) (ii) and its
successors, and use, duplication, disclosure by the Government is subject to restrictions as set forth in
subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at
252.227-7013. Cabletron Systems, Inc., 35 Industrial Way, Rochester, New Hampshire 03867-0505.
book Page iv Thursday, April 18, 1996 2:18 PM

Notice
BRIM-A6 User’s Guide v
DECLARATION OF CONFORMITY
Application of Council Directive(s): 89/336/EEC
73/23/EEC
Manufacturer’s Name: Cabletron Systems, Inc.
Manufacturer’s Address: 35 Industrial Way
PO Box 5005
Rochester, NH 03867
European Representative Name: Mr. J. Solari
European Representative Address: Cabletron Systems Limited
Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG13 2PZ, England
Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC
EC Directive 73/23/EEC
EN55022
EN 50082-1
EN 60950
Equipment Type/Environment: Networking Equipment, for use in a Commercial or Light
Industrial Environment.
We the undersigned, hereby declare that the equipment packaged with this notice conforms to the
above directives.
Manufacturer Legal Representative in Europe
Mr. Richard Michaud Mr. J. Solari
___________________________________ ___________________________________
Full Name Full Name
Manager of Engineering Services Managing Director - E.M.E.A.
___________________________________ ___________________________________
Title Title
Rochester, NH, USA Newbury, Berkshire, England
___________________________________ ___________________________________
Location Location
book Page v Thursday, April 18, 1996 2:18 PM

BRIM-A6 User’s Guide vii
CONTENTS
CHAPTER 1 INTRODUCTION
1.1 Using This Manual.......................................................................1-1
1.2 Document Conventions...............................................................1-2
1.3 BRIM-A6 Overview......................................................................1-3
1.4 BRIM-A6 Features.......................................................................1-3
1.5 BRIM-A6 Specifications...............................................................1-4
1.6 Related Manuals..........................................................................1-4
1.7 Getting Help.................................................................................1-5
CHAPTER 2 INSTALLATION
2.1 Unpacking the BRIM....................................................................2-1
2.2 Installing APIMs...........................................................................2-2
2.3 Installing BRIMs...........................................................................2-3
2.3.1 Installing a BRIM in a MIM..............................................2-3
2.3.2 Installing a BRIM in a Hub ..............................................2-5
CHAPTER 3 LOCAL MANAGEMENT
3.1 Local Management Keyboard Conventions.................................3-2
3.2 Using LIM to create PVCs...........................................................3-3
3.2.1 ATM Connection Tables Screen Fields ..........................3-4
3.2.2 ATM Connection Tables Screen Commands .................3-5
3.2.3 Using ATM Connection Tables Screen Commands .......3-5
3.2.4 Adding PVCs to the Connection Tables Screen.............3-6
3.2.5 Deleting PVCs from the Connection Tables Screen.......3-6
3.3 Using LM to Create PVCs ...........................................................3-7
3.3.1 BRIM-A6 Setup Screen Fields........................................3-8
3.3.2 BRIM-A6 Setup Screen Commands...............................3-9
3.3.3 Using BRIM-A6 Setup Screen Commands...................3-10
3.3.4 Accessing the BRIM-A6 Add/Delete Entry Screen .......3-10
3.3.5 BRIM-A6 Add/Delete Entry Screen Fields....................3-11
3.3.6 BRIM-A6 Add/Delete Entry Screen Commands ...........3-12
3.3.7 Adding a PVC ...............................................................3-12
3.3.8 Modifying a PVC...........................................................3-13
3.3.9 Deleting a PVC .............................................................3-14
CHAPTER 4 LANVIEW LEDs
4.1 BRIM-A6 LEDs............................................................................4-1
4.2 APIM LEDs..................................................................................4-2
book Page vii Thursday, April 18, 1996 2:18 PM

Contents
viii BRIM-A6 User’s Guide
APPENDIX A APIM SPECIFICATIONS
A.1 APIM-11 Specifications...............................................................A-1
A.2 APIM-21 Specifications...............................................................A-1
A.3 APIM-22 Specifications...............................................................A-2
A.4 APIM-29 Specifications...............................................................A-2
A.5 APIM-67 Specifications...............................................................A-3
APPENDIX B ATM OVERVIEW
B.1 ATM Basics.................................................................................B-1
B.2 The ATM Cell.............................................................................. B-2
B.3 The ATM Network....................................................................... B-4
B.3.1 Virtual Channels and Virtual Paths................................. B-4
B.3.2 Permanent and Switched Virtual Channels....................B-5
B.4 ATM Protocol .............................................................................. B-5
book Page viii Thursday, April 18, 1996 2:18 PM

BRIM-A6 User’s Guide Page 1-1
CHAPTER 1
INTRODUCTION
Welcome to the Cabletron Systems BRIM-A6 User’s Guide . This
manual provides the following information:
• Describes BRIM-A6 features
• Explains how to install the BRIM-A6 in a Cabletron Systems Media
Interface Module (MIM) or standalone hub
• Outlines specifications for the Cabletron Systems Asynchronous
Transfer Mode (ATM) Bridge/Router Interface Module (BRIM)
The BRIM-A6 provides additional connectivity/functionality to various
Cabletron Systems MIMs and standalone hubs.You should have a general
working knowledge of ATM networks and the ATM User-Network
Interface Specification, as proposed in theATM Forum, prior to installing
the BRIM-A6. If you need a basic overview ofATM, refer toAppendix B,
ATM Overview .
1.1 USINGTHIS MANUAL
Read through this manual completely to familiarize yourself with its
content and to gain an understanding of the features and capabilities of
the BRIM-A6. The following list provides an overview of each section of
this manual:
Chapter 1,
Introduction , outlines the contents of this manual, describes
BRIM-A6 features and concludes with a list of related manuals.
Chapter 2, Installation , describes how to install ATM Port Interface
Modules (APIMs) into the BRIM-A6. This chapter also explains how to
install a BRIM-A6 into a MIM or a standalone hub.
Chapter 3,
Local Management , describes how to create Permanent
Virtual Connection using Cabletron Systems Local Interface Management
(LIM) or Cabletron Systems Local Management (LM).
Chapter 4,
LANVIEW LEDS , describes how to use the BRIM-A6 LEDs
to monitor BRIM performance and status.
book Page 1 Thursday, April 18, 1996 2:18 PM

Chapter 1: Introduction
Page 1-2 BRIM-A6 User’s Guide
Appendix A, APIM Specifications , describes specifications and features
for each of the APIMs available for the BRIM-A6.
Appendix B, ATM Overview , provides a basic overview of ATM
technology.
1.2 DOCUMENT CONVENTIONS
The following conventions are used throughout this document:
NOTE
Note symbol. Calls the reader’s attention to any item of
information that may be of special importance.
TIP
Tip symbol. Conveys helpful hints concerning procedures or
actions.
!
CAUTION
Caution symbol. Contains information essential to avoid
damage to the equipment.
Warning symbol.Warns against an action that could result in
equipment damage, personal injury or death.
book Page 2 Thursday, April 18, 1996 2:18 PM